Fabrication of fluorine-terminated diamond-like carbon thin film using a hyperthermal atomic fluorine beam

Surface modification of diamond-like carbon (DLC) film was performed using a hyperthermal atomic fluorine beam on the purpose of production of hydrophobic surface by maintaining the high hardness of DLC film. By the irradiation of atomic fluorine beam of a 1.0 × 10²⁰ atoms/cm², the contact angle of a water drop against the DLC surface increased from 73° to 111°. The formation of CF₃, CF₂ and CF bonding on the modified DLC surface was confirmed from the measurements of X-ray photoelectron spectra and near-edge X-ray absorption fine structure spectra. Irradiation of hyperthermal atomic fluorine beam was concluded to produce insulator fluorine-terminated DLC film, which has high F content on the surface, by the taking of the use of neutral atomic beam as a fluorine source.     

Silicon quantum dot superlattice solar cell structure including silicon nanocrystals in a photogeneration layer

The solar cell structure of n-type poly-silicon/5-nm-diameter silicon nanocrystals embedded in an amorphous silicon oxycarbide matrix (30 layers)/p-type hydrogenated amorphous silicon/Al electrode was fabricated on a quartz substrate. An open-circuit voltage and a fill factor of 518 mV and 0.51 in the solar cell were obtained, respectively. The absorption edge of the solar cell was 1.49 eV, which corresponds to the optical bandgap of the silicon nanocrystal materials, suggesting that it is possible to fabricate the solar cells with silicon nanocrystal materials, whose bandgaps are wider than that of crystalline silicon.

PACS

85.35.Be; 84.60.Jt; 78.67.Bf     

Investigation of hydrogen plasma treatment for reducing defects in silicon quantum dot superlattice structure with amorphous silicon carbide matrix

We investigate the effects of hydrogen plasma treatment (HPT) on the properties of silicon quantum dot superlattice films. Hydrogen introduced in the films efficiently passivates silicon and carbon dangling bonds at a treatment temperature of approximately 400°C. The total dangling bond density decreases from 1.1 × 10¹⁹ cm^-3 to 3.7 × 10¹⁷ cm^-3, which is comparable to the defect density of typical hydrogenated amorphous silicon carbide films. A damaged layer is found to form on the surface by HPT; this layer can be easily removed by reactive ion etching.     

Preparation of pectin‐inorganic composite material as accumulative material of metal ions

Pectin is one of the biopolymers in the cell walls of all plant tissues, but the pectin‐containing materials have been discarded as industrial waste in food‐processing factories. We prepared a water‐insoluble pectin‐inorganic composite material by mixing pectin and a silane coupling reagent, bis(3‐trimethoxysilylpropyl)amine. The mechanical strength of the pectin‐inorganic composite material was higher than that of the pectin material without the addition of an inorganic component. In addition, the thermal stability of the composite material increased with the addition of the inorganic component. Furthermore, when the pectin‐inorganic composite materials were incubated in an aqueous solution of Cu(II), Zn(II), or In(III), these composite materials effectively accumulated not only the heavy metal ions, but also rare‐earth metal ions. Additionally, based on the infrared (IR) measurements, the metal ion accumulative mechanism into the composite material is described. As a result, the IR spectra suggested an electrostatic interaction between the metal ion and carboxy group in the pectin. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42056.     

Anhydrous proton conductor consisting of pectin–inorganic composite material

An organic–inorganic proton conductive composite material consisting of a biopolymer was prepared by mixing the pectin, tetraethyl titanate, and imidazole. Although the pectin material without the composite dissolved in water, the pectin–inorganic composite material did not show water solubility. In addition, in the composite material, the pectin and imidazole formed an acid–base structure by an electrostatic interaction, and as a result, these composite materials showed a thermal stability at intermediate temperatures (100–200°C). Furthermore, these composite materials indicated the proton conductivity of 5.6 × 10^?4 S cm^?1 at 180°C under anhydrous conditions. The activation energy of the proton conduction under anhydrous conditions was 0.32–0.22 eV and these values were one order of magnitude higher than that of the typical humidified perfluorinated membrane, such as Nafion^®. The organic–inorganic composite material consisting of a biocomponent may have the potential to be utilized as a novel proton conductor under anhydrous conditions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42433.     

Direct ethoxylation of fatty methyl ester over Al-Mg composite oxide catalyst

For the purpose of estimating the reaction mechanism of the direct ethoxylation of a fatty ester in the presence of an Al-Mg composite oxide catalyst, a labeled fatty methyl ester C₁₁H₂₃CO¹⁸OCH₃ containing ¹⁸O isotope was synthesized and directly ethoxylated. The product was evaluated by gas chromatography-mass spectrometry (GC-MS). The GC-MS spectra showed that the ¹⁸O isotope label was present only in the methoxy group at the molecular end of the ethoxylated fatty methyl ester. This supports the reaction mechanism of coordination anionic polymerization where the bond between the acyl and methoxy groups of the fatty methyl ester molecule was broken, caused by the bifunctional effect of the acid-base active sites; an intermediate chemisorption species was formed; and then ethylene oxide was addition-polymerized sequentially, in parallel.     

Low-temperature selective reduction of NO with propene over alkaline-exchanged mordenites

Partially protonated alkaline mordenites showed higher activity per acid amount below 573 K than acidic zeolites for the selective reduction of NO with C₃H₆ in the presence of O₂, which can be related to a high concentration of NO₃ ^- species in the zeolite channels. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effect of cell structure on oil absorption of highly oil absorptive polyurethane foam for on-site use

This article reports the effect of cell structure on oil absorption of highly oil-absorptive polyurethane foam (ON-PUR), which is suitable for on-site foaming. We have developed ON-PUR as an oil absorbing polyurethane foam using a very reactive recipe. ON-PUR was synthesized by mixing polyol, water, additives, and polymeric diphenylmethane diisocyanate (P-MDI) using a high-pressure foaming machine. Density, airflow, oil absorption of this foam, and cell structure by microscopy were measured. From these results, it was found that the airflow of this foam increased by crushing, and the oil absorption of this foam increased sharply in a narrow airflow range (from 0.1 to 0.8 scfm). This increase is estimated to be due to the decrease of closed cell structures by crushing treatment. Furthermore, we constituted on-site foaming system in bench scale, which was expected to be applicable to on-site preparation of ON-PUR. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 179–186, 1997     

The formation of graphene–titania hybrid films and their resistance change under ultraviolet irradiation

We report the fabrication of hybrid films of graphene and monolayer titania using a simple electrostatic self-assembly method. Ultraviolet (UV) responses of the hybrid films based on the graphene–titania structure were investigated. We observed that the resistance of the graphene–titania hybrid increased exponentially with UV irradiation time and decreased exponentially when UV was turned off. Time constants of the order of hundreds of seconds were identified and found to be sensitive to the gas environment of graphene. The UV response as well as the time constant is tunable by varying the number of titania layers. Our results confirmed that UV irradiation played a significant role in the resistance modulation of graphene as well as graphene–titania hybrid films.     

Improvement on sulfate resistance of blended cement with high alumina slag

This paper is focused on the effect of limestone and calcium sulfate content on sulfate resistance of ground granulated blast furnace slag (GGBS) blended cement. Sulfate resistance was evaluated using ASTM C 1012, and a variety of mechanisms of the sulfate resistance of GGBS blended cement were revealed by the analyses of hydration products and sulfate ion ingress. Although GGBS suppresses sulfate ion ingress, it is probable that alumina in GGBS tends to form ettringite with externally supplied sulfate ions. Addition of limestone and increase in calcium sulfate content allow both monocarboaluminate and ettringite to form prior to immersion in sulfate solution. These hydration products remain in the hardened cement matrix and act to suppress further formation of ettringite with external sulfate ions during immersion in sulfate solution. GGBS blended cement with a suitable amount of limestone powder and a controlled content of calcium sulfate exhibits markedly long term sulfate resistance.