Printing cotton fabrics with reactive dyes of high reactivity from an acidic printing paste

The behaviour of reactive dyes of high reactivity during the printing process of 100% cotton fabrics from an alkaline and acidic printing paste was studied in detail. The printing pastes were stored for different periods of time and then the fabrics were printed. The samples were subjected to two methods of fixation, the first by steaming and the second by thermofixation. The effects of different factors such as alkali and acid concentration, storage time of the printing pastes and method of fixation on the K/S values of the prints were investigated. The fastness properties of the printed areas were also measured to determine the improvement obtained by acidic printing with high-reactivity reactive dyes on cotton fabrics.     

Dense Al2O3/ZrO2 Particulate Composites by Free Sintering of Coated Powders

Composite powders, prepared by coating coarse ZrO₂ particles with fine Al₂O₃ powder using a chemical precipitation technique, were compacted and sintered freely at a constant heating rate of 4°C/min to ∼1600°C. Composites containing up to ∼30 vol% inclusions were sintered to nearly full density under the same conditions used for the unreinforced matrix. Furthermore, the sintering kinetics were not influenced significantly by the inclusion volume fraction. The sinterability of the composites formed from the coated powders was significantly better than that for similar composites formed from mechanically mixed powders. The present data provide a further demonstration that the use of coated powders may have widespread applicability for the fabrication, by free sintering, of dense ceramic particulate composites.     

HColonies: a new hybrid metaheuristic for medical data classification

Medical data feature a number of characteristics that make their classification a complex task. Yet, the societal significance of the subject and the computational challenge it presents has caused the classification of medical datasets to be a popular research area. A new hybrid metaheuristic is presented for the classification task of medical datasets. The hybrid ant–bee colonies (HColonies) consists of two phases: an ant colony optimization (ACO) phase and an artificial bee colony (ABC) phase. The food sources of ABC are initialized into decision lists, constructed during the ACO phase using different subsets of the training data. The task of the ABC is to optimize the obtained decision lists. New variants of the ABC operators are proposed to suit the classification task. Results on a number of benchmark, real-world medical datasets show the usefulness of the proposed approach. Classification models obtained feature good predictive accuracy and relatively small model size.     

Thermal decomposition behavior of γ‐irradiated poly(vinyl acetate)/poly(methyl methacrylate) miscible blends

Miscible polymer blends based on various ratios of poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA) were prepared in film form by the solution casting technique using benzene as a common solvent. The thermal decomposition behavior of these blends and their individual homopolymers before and after γ‐irradiation at various doses (50–250 kGy) was investigated. The thermogravimetric analysis technique was utilized to determine the temperatures at which the maximum value of the rate of reaction (T_max) occurs and the kinetic parameters of the thermal decomposition. The rate of reaction curves of the individual homopolymers or their blends before or after γ‐ irradiation displayed similar trends in which the T_max corresponding to all polymers was found to exist in the same position but with different values. These findings and the visual observations of the blend solutions and the transparency of the films gave support to the complete miscibility of these blends. Three transitions were observed along the reaction rate versus temperature curves; the first was around 100–200°C with no defined T_max, which may arise from the evaporation of the solvent. The second T_max was in the 340–380°C range, which depended on the polymer blend and the γ‐irradiation condition. A third transition was seen in the rate of reaction curves only for pure PVAc and its blends with PMMA with ratios up to 50%, regardless of γ‐ irradiation. We concluded that γ‐irradiation improved the thermal stability of PVAc/PMMA blends, even though the PMMA polymer was degradable by γ irradiation. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1773–1780, 2006     

Electrosynthèse des ions peroxodiphosphate sous potentiel constant ou pulsé

Electrosynthesis of peroxodiphosphate ions (P2O84–) was performed in 2m K3PO4, 1m K2HPO4 medium, using a platinum anode. The results showed that under conditions of potentiostatic polarization at constant potential, the reaction rate reaches a maximum value of 125mAcm–2 and a faradaic yield of 30%. From about 1.9V, the reaction kinetics are increasingly inhibited as the potential shifts positively. Rapid scanning potential voltammetry was used to characterize the oxidation state of the electrode surface. This method shows that the growth of (PtO) and (PtO2 or PtO3) oxides depend on the applied potential. It also establishes a correlation between the inhibition of P2O84– ion electrosynthesis and the oxide coating surface. When 2×10–3m KSCN is added to the solution, some oxygen evolution sites are selectively blocked and oxide occurs at more positive potential values. Consequently, the rate of peroxodiphosphate ion formation and the faradaic efficiency are increased to 380mAcm–2 and 75%, respectively. Under pulsed potential conditions it was possible to reach 1200mAcm–2 for P2O84– ion electrosynthesis with a faradaic yield of 82%.     

Rheological behaviour of polysaccharide aqueous solutions

Several data relative to the viscosity of water-soluble polysaccharide solutions were collected from the literature and processed by different rheological models. Some relationships between the viscosity of these polymer solutions, their molecular weight and their solution concentrations, were established and their validity checked. Thus, an accurate equation correlating the viscosity and both the shear rate and the solution concentration of different water soluble polysaccharides (xanthan, hyaluronan, carboxymethylcellulose) was deduced on the basis of Cross' model which suggests two domains in which the viscosity is constant, i.e. very low and very high shear rate ranges. Then, an expression relating the zero-shear viscosity (A) and the concentration of their solutions was proposed. Finally, an alternative equation to that of Mark–Houwink correlating the molecular weight and the intrinsic viscosity of the water-soluble polysaccharides studied in this paper was found.     

Study of Hydrodynamics,Mixing and Gas‐Liquid Mass Transfer in a Split‐Rectangular Airlift Reactor

Global hydrodynamic characteristics, liquid mixing and gas‐liquid mass transfer for a 63 L split‐rectangular airlift reactor were studied. Correlations for gas holdup and overall liquid circulation velocity were derived for the air‐water system as a function of the specific power input; these were compared to data and correlations for reactor volumes between 4.7 L and 4600 L. A partial recirculation of small bubbles in the riser was observed when U_gr > 0.03 m/s, which was attributed to the use of a single‐orifice nozzle as the gas phase distributor. The dimensionless mixing time and the overall axial dispersion coefficient were nearly constant for the range of gas flow rates studied. However, values of K_L/d_B were greater than those reported in previous studies and this is caused by the partial recirculation of the gas phase in the riser. While scale effects remain slight, the use of a gas distributor favouring this partial recirculation seems adequate for mass transfer in split‐rectangular airlift reactors.     

Modification of leather properties by grafting. I. Effect of monomer chain on the physico‐mechanical properties of grafted leather

Although leather has a number of desirable properties such as thermal stability and fire retardancey, in addition to high toughness, it has a few drawbacks such as weight, high water absorption, poor soil and rot resistance, and nonuniformity. If these defects are overcome, leather's usefulness would be further enhanced and its competitive position with respect to synthetics would increase. This study reports the physical and mechanical properties of buffalo leather after chemical graft copolymerization with ethyl acrylate, butyl acrylate, and 2‐ethyl hexyl acrylate using benzoyl peroxide as an initiator. The optimum conditions for grafting (e.g., monomer and initiator concentrations, temperature and time of grafting, and solvent leather ratio) were extensively investigated. The study achieved outstanding properties for buffalo leather in reduction of water uptake after grafting, especially on using 2‐ethyl hexyl acrylate and butyl acrylate monomers. FT‐IR and solid ¹³C‐NMR for leather before and after grafting confirmed the grafting process.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1478–1483, 2003     

Functional properties of a protein product from Caryodendron orinocense (Barinas nut)

The functional properties of Caryodendron orinocense protein product were investigated and compared with those of soybean (Glycina maxima). The product protein content was 24.47 g/100 g (Nx6.25). Solubility increased at both sides of the isoelectric point (pH 4.0) and with increased NaCl concentration up to 0.5M. Compared with soybean flour (50% protein), the protein product exhibited higher water and oil absorption, but lower emulsifying activity, emulsion stability, foaming capacity, and foam stability, the last one increase at higher pH. Emulsifying activity, foaming capacity, and foam stability were ionic strength dependent. C. orinocense protein product increased its emulsifying activity steadily from 0.05M to 0.75M NaCl, while it remained almost constant for soybean flour. Foaming capacity increased drastically at pH 10. The minimum time and concentration to form a gel was 20% in 4 min and 10% in 8 min for the Caryodendron protein product and soybean flour, respectively. The bulk density was 0.5056+/-0.0041 g/mL.     

Grafting poly(t‐butyl acrylate) to poly(allylamine) by inverse microemulsion radical polymerization: From comb‐polymer to amphiphilic shell crosslinked polymer nanocapsule

An interfacial grafting radical polymerization method for amphiphilic comb copolymer and shell crosslinked polymer nanocapsules was reported. Macropolyradicals on a water soluble long chain polyamine were generated with hydrogen peroxide in the water phase and subsequent grafting radical polymerization of a vinylic monomer at the water/oil interface proceeded at 65°C. In the presence of a crosslinker, the resulting graft copolymer formed a defined core‐shell structure with hydrophilic aqueous core functionalized by the polyamine and a hydrophobic crosslinked polymer shell. The structure of the core‐shell material was characterized by NMR, FTIR, DSC, TGA, SEM, TEM, and the mechanism of the graft polymerization is proposed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1905–1911, 2007