Inter-comparative study of quantitative methods of industrial clinker

Impurities from the raw materials, the grinding and the homogenization of the raw materials, the kiln instability and the complexity of the cooling step, all these factors make it difficult to obtain a perfect evaluation of the mineralogical composition of Portland clinker. We studied the limitations of the most commonly used quantitative methods and recommend some procedures to obtain reliable and reproducible results of quantitative analyses. Different clinker samples (provided by the Bizerte Cement Company (Tunisia)) were subjected to an elemental analysis by X-ray fluorescence and the mineralogical composition was determined by the Bogue calculation and by X-ray powder diffraction combined with the Rietveld method (Different softwares were used: XPert High Score Plus version 2.0 and TOPAS version 4.2). We then compared the results obtained by the Rietveld method and the Bogue calculation to the specific peak areas of each phase. The content of each phase, determined by the Rietveld method, varied proportionally to the change in peak area; a significant difference in these results was found by using the elementary Bogue calculation.     

Temperature and processing effects on lithium ion conductivity of solution-deposited lithium zirconium phosphate (LiZr2P3O12) thin films

Lithium zirconium phosphate (LiZr₂P₃O₁₂) thin films have been prepared on platinized silicon substrates via a chemical solution deposition approach with processing temperatures between 700°C and 775°C. Films that were subject to a single high-temperature anneal were found to crystallize at temperatures above 725°C. Crystallization was observed in films annealed after each deposited layer at 700°C and above. In both cases, grain size was found to increase with annealing temperature. Ion conductivity was found to increase with annealing temperature in singly annealed films. In per-layer annealed films ion conductivity was found to initially increase then decrease with increasing annealing temperature. A maximum ion conductivity of 1.6 × 10⁻⁶ S/cm was observed for the singly annealed 775°C condition, while a maximum ion conductivity of 5.8 × 10⁻⁷ S/cm was observed for the 725°C per-layer annealed condition. These results are consistent with an increasing influence of cross-plane, internal interface resistance and vapor phase carrier loss in the per-layer annealed samples. This work demonstrates that post-deposition processing methods can strongly affect the ion conducting properties of LiZr₂P₃O₁₂ thin films.     

Great enhancement of mechanical features in PLA based composites containing aligned few layer graphene (FLG), the effect of FLG loading,size, and dispersion on mechanical and thermal properties

Four series of polylactide (PLA) based composite films containing horizontally aligned few layer graphene (FLG) flakes of high aspect ratio and adsorbed albumin are prepared. The mechanical and thermal properties varies with percentage, dispersion degree and size of FLG flakes. Great improvement up to 290% and 360% of tensile modulus and strength respectively were obtained for the composite containing high lateral size of FLG at 0.17% wt, and up to 60% and 80% for the composite with very well dispersed 0.02% wt FLG. The composites of PLA and PEG-PLLA containing very well dispersed FLG flakes at 0.07% wt are ductile showing enhancement of elongation at break up to respectively 80% and 88%. Relatively high electrical conductivity, 5 × 10⁻³ S/cm, is measured for PLA film charged with 3% of FLG.     

Crack growth angle prediction of an internal crack under mixed mode load for unfilled elastomer using the strain energy density factor

This article investigates the prediction of the crack growth angle of an existing internal crack under mixed mode loading at the crack tip for an unfilled ethylene propylene diene terpolymer rubber (EPDM). For the realization of mixed mode loading, the cracks of the uniaxial loaded specimens were oriented with different angles to the loading direction. The energy density factor was used as a potential criterion for determining the crack growth angle. The determination of the strain energy density factor was carried out simulatively in Abaqus. The second-order Ogden model was used to describe the rubber-like material behavior. The relative local minimum of the strain energy density factor provides the possible growth angle. The experimental investigations show that the initial cracks grow orthogonally to the loading direction for the different crack orientation angles. For the crack orientation angle parallel to the load direction, the crack growth was observed because the strong stretching of the specimen caused strong necking in the crack region. The crack growth for the remaining crack orientation angles were induced due to shear loading at the crack tip. The predictive angle of different crack orientation angles shows very good accordance to the measured crack growth angles.     

Equation of state and the dynamic compression of cerium in the range of the γ-α phase transition

A thermodynamically complete equation of two-phase (γ, α) state of cerium was derived in terms of a pseudobinary solid-solution model developed by Aptekar’ and Ponyatovskii. According to the model, unalloyed cerium is considered to be a substitutional solid solution whose components are represented by atoms with different electron configurations. The free energy of the individual phases (solid-solution components) is represented as a sum of three terms that describe the atomic interaction at T = 0 K, quasi-harmonic lattice vibrations, and the combined contribution of the anharmonicity and thermally excited electrons. The equation of state is shown to adequately describe the unusual behavior of cerium under the effect of static actions. In this work, calculations of the dynamic compression of cerium are performed. The calculations indicate that, up to the completion of the γ-α transition, the formation of the shockwave front in cerium is impossible and compression of cerium occurs in an isentropic wave of simple compression. As the pressure increases, a multiwave configuration with the participation of isentropic and shock waves is realized in cerium. The initial state in which the shock wave is propagated changes depending on the wave intensity; i.e., the initial state “slides” along the leading isentropic wave. The shock adiabat was shown to not pass through the very complex range of metastable existence of α-, α′-, and α″ phases. This provides prerequisites for experimental finding the α-ε transformation which can occur in the shock wave and is not masked with the preceding α-α′ and α′-α″ transformations. When assuming the absence of the α-ε transformation, the calculated coordinates of the point corresponding to the start of melting in the shock wave are p _melt = 11.3 GPa and T _melt = 1130 K.     

Breakdown of passive film on nickel in borate solutions containing halide anions

The effect of Cl⁻, Br⁻ and I⁻ anions as aggressive agents on the anodic behaviour of nickel electrode in deaerated Na₂B₄O₇ solutions have been investigated by galvanostatic polarization technique. Lower concentrations of the halide anions have no effect on the mechanism of nickel passivation. An increase in the halide anions concentration causes oscillation of the potential in the oxygen evolution region. This could be attributed to the destruction of the passivity by halide anions and repassivation of the film by anodic current and/or OH⁻ anions. Higher aggressive anion concentrations cause breakdown of the passive film and initiated pitting corrosion. As the temperature increases, the breakdown potential is shifted towards the more negative direction. On the other hand, as the pH of the solution increases, the breakdown potential is shifted toward more positive direction, indicating increased protection of the passive film. The activation energy, , of the oxide film formation in the presence of Cl⁻ anions was calculated and was found to be 21 kJ/mol.     

Investigations on composition and morphology of electrochemical conversion layer/titanium dioxide deposit on stainless steel

In this study, the formation and characterization of conversion coatings modified by a sol-gel TiO₂ deposit were investigated as a way to develop a new photocatalyst for water and air depollution. The conversion coating, characterised by strong interfacial adhesion, high roughness and high surface area facilitates the sol-gel deposition of titania and enhances its adhesion to the substrate. The conversion treatment is carried out in an acid solution. Observation by Scanning Electron Microscopy (SEM) reveals a rough surface with pores and cavities. According to SIMS measurements, the thickness of the initial conversion layer is evaluated at about 1.5 μm. On this pre-functionalised support, the titanium dioxide was deposited by the sol-gel method. The roughness measurements coupled with SIMS analysis allowed a precise evaluation of the surface state of the final layers. The coating consists of two layers: a TiO₂ outer layer and an inner layer containing iron chromium oxides. Characterization by X-ray diffraction (XRD) showed the existence of the TiO₂ anatase structure as the main compound.     

A robust estimation approach for uncertain systems with perturbed measurements

This paper deals with state estimation problem for uncertain continuous‐time systems. A numerical treatment is proposed for designing interval observers that ensures guaranteed upper and lower bounds on the estimated states. In order to take into account possible perturbations on the system and its outputs, a new type of interval observers is introduced. Such interval observers consist of two coupled general Luenberger‐type observers that involve dilatation functions. In addition, we provide an optimality criterion in order to find optimal interval observers that lead to tight interval error estimation. The proposed existence and optimality conditions are expressed in terms of linear programming. Also, some illustrative examples are given. Copyright © 2015 John Wiley & Sons, Ltd.     

Effects of frequency dimming electronic ballast on a high‐pressure mercury thallium iodide discharge

This study focuses on the behavior of a cylindrical metal halide discharge lamp powered by frequency‐controlled electronic ballast. Half‐bridge electronic ballast was designed and achieved.