Evaluation of the effects of acetyl tributyl citrate as bio‐based plasticizer on the physical,thermal, and dynamical mechanical properties of poly(vinyl chloride)/polymethyl methacrylate blends

This article details our work in studying the plasticization of Poly(vinyl chloride) (PVC)/Polymethyl methacrylate (PMMA) blends with bio‐based acetyl tributyl citrate (ATBC) in place of conventional plasticizers such as di(2‐ethylhexyl) phthalate. PMMA was blended with PVC in various ratios from 0 to 100 wt% by melt compounding with or without the plasticizer ATBC. Both the glass transition temperatures of the blends (differential scanning calorimetry) and Tα (dynamic mechanical thermal analysis) are consistent with a miscibility of the components, and Fourier transforms infrared spectroscopy studies show that there are specific interactions in the PVC/PMMA blends favoring the miscibility. The thermal degradation of the blends was studied by thermogravimetric analysis that shows the thermal degradation of rigid and plasticized PVC/PMMA is a process composed of two‐steps and that PMMA exercises a stabilizing effect on the thermal degradation of PVC during the first step by decreasing the rate of dehydrochlorination. J. VINYL ADDIT. TECHNOL., 25:E73–E82, 2019. © 2018 Society of Plastics Engineers     

Wear and Tribological Performance of Different Ceramic Tools in Dry High Speed Machining of Ni-Co-Cr Precipitation Hardenable Aerospace Superalloy

Tool wear is an important machinability criterion. To reduce total machining costs, this study demonstrates the wear and tribological performance of four ceramic tools in dry high-speed turning of Ni-Co-Cr precipitation hardenable superalloy (Inconel 100). Wear of the tool materials and the structural and phase transformations at the tool–chip interface were investigated. Results obtained reveal that SiAlON ceramic outperformed other ceramic tool materials at different cutting speeds due to the formation of a large amount of mullite tribofilms on the tool face, which serve as a thermal barrier layer. Alumina ceramic with the addition of ZrO₂ can be recommended for machining Inconel 100 at speeds above 150 m/min due to its ability to form thermal barrier ZrO₂ tribofilms, which decrease the coefficient of friction at the tool–chip interface. Mixed alumina and an alumina matrix reinforced with SiC_w were found to be unsuitable for machining age-hardened Inconel 100 superalloy.     

Reflection and refraction of incident p-, T-, and SV-waves at interface between magnetized two solid-liquid media with heat sources and initial stress with and without thermal relaxation times

We investigate the problem of reflection and refraction of thermoelastic waves at a magnetized solid-liquid interface in presence of initial stress. In the context of Green-Lindsay and coupled thermoelastic theories of thermoelasticity, the problem has been solved and the effect of magnetic field, external heat sources, and initial stress on p-, T-, and SV-waves propagation have been discussed. The boundary conditions at the interface for displacement continuity, vanishing the tangential displacement, continuity of normal force, tangential force, and continuity of temperature are applied. The amplitudes ratios for the incident p-, T-, and SV-waves have been obtained. The effect of the initial stress, heat sources, and magnetic field on the reflection and transmitted coefficients for the incident waves have been discussed.     

Structural,magnetic, and optical properties of nano-sized Ni0.85Se

Nanocrystalline Ni_0.85Se was synthesized by a hydrothermal method. X-ray diffraction analysis by Rietveld method indicated that Ni_0.85Se has a NiAs-type hexagonal structure. Narrow crystallite size distribution with an average area-weighted size of 〈ɛ_F〉 = 8.5 nm is obtained by Warren-Averbach method. Structural analysis revealed deformed Se atoms octahedron with the shortest distance between Se atoms in adjacent planes 〈Se–Se〉_adj smaller than between nearest neighbors in layer plane 〈Se–Se〉_nea, and a rather short interatomic distance between the transition metal atoms 〈Ni–Ni〉. The optical property of Ni_0.85Se was studied by UV-spectroscopy. Magnetic measurement shows a ferromagnetic phase transition for Ni_0.85Se below 14 K.     

Optical and mechanical characterization of transparent α-alumina fabricated by spark plasma sintering

The aim of this work was the analysis of the experimental results of a transparent alumina (BMA15) ceramic which was fabricated by Spark Plasma Sintering (SPS) from nanopowder (BMA15, Baikowski Chimie, France), at different temperatures (1200°C, 1250°C, 1300°C). With the application of a maximum uniaxial pressure of 73 MPa during all the fabrication-cycle (more than 3 hours). We sought an optimal sintering temperature combining better optical and mechanical properties of our pellets. The sintered alumina (BMA15) has a crystalline and dense microstructure. The samples sintered at 1200°C exhibit the best optical properties, in particular: good real inline transmission (RIT) and an optical gap greater than those of the samples sintered at 1250°C and 1300°C. Due to their low density, the Young modulus of alumina sintered at 1200 °C, deduced by ultrasound, has a low value which is about 385 GPa. Similarly, its small grain size gives it a better Vickers hardness ~ 21 GPa. Therefore, the value of the coefficient of friction μ stabilizes around the mean value of 0.21.     

Electrical and Dielectric Characterizations of Cu2ZnSnSe4/n-Si Heterojunction

Silicon - Cu2ZnSnSe4 (CZTSe) thin film has been synthesized onto silicon substrates by liquid phase epitaxial growth for the first time in which Au/CZTSe/n-Si/Al heterojunction was successfully...     

Influences of Mn doping on the microstructural,semiconducting, and optoelectronic properties of HgO nanostructure films

Mn-doped HgO nanostructured thin films (Hg_1-xMn_xO) have been prepared using electron beam evaporation technique on Corning glass (1022) substrate at room temperature with different concentrations x = 0, 0.015, 0.05, 0.1, 0.15, and 0.2. The microstructural, morphological, semiconducting, and optoelectronic properties of the films have been investigated. The X-ray diffraction spectra suggest a hexagonal wurtzite type structure with lattice parameters decreased with increasing Mn content. It was found that the average particle size of the films decreases with increasing Mn doping which is confirmed by FE-SEM and AFM micrographs. The optical band gap of the investigated Mn-doped HgO nanocrystalline films is determined from the absorption coefficient and found to increase with the increase of Mn concentration which is attributed to the sp-d exchange interaction and/or the quantum confinement effect. The refractive index and extinction coefficient of the Mn-doped HgO films are also reported. The refractive index dispersion n(λ) is analyzed by single-effective-oscillator dispersion model proposed by the Wemple–DiDomenico (WDD). The oscillator parameters were estimated. The obtained dispersion values are suitable for the design of optoelectronic devices.     

Dielectric and mechanical optimization properties of porous poly(ethylene‐co‐vinyl acetate) copolymer films for pseudo‐piezoelectric effect

In this article, the authors present a porous copolymer film with pseudo‐piezoelectric effects as a new candidate material for sensing applications. Porous films of poly(ethylene‐co‐vinyl acetate) (EVA) with a thicknesses ranging from 160 to 310 μm are fabricated by a coextrusion chemical foaming process and charged using a high‐voltage contact charging process. Output performances (piezoelectric constant and relative permittivity) with related thermal/mechanical stability are specifically studied as a function of the film porosity and of the electrical charging process. The piezoelectric constant d₃₃ increases with the cell porosity and an interesting piezoelectric constant close to 5.1 pC/N is achieved with a porous EVA film containing 65% of porosity. Actual results are then discussed using a theoretical solid–gas multilayer model to describe and predict the pseudo‐piezoelectric effect of porous polymer materials. The originality of this work lies in the fact that all the steps leading to optimize pseudo piezoelectric films are included, and also in the use of EVA which is not a standard piezoelectric material. Therefore, this work is a contribution in the development of low‐cost piezoelectric materials with potential applications as sensor in different fields such as medical, security, environment, sport, and transport. POLYM. ENG. SCI., 59:1455–1461 2019. © 2019 Society of Plastics Engineers     

Diglycidyl ether of bisphenol A/chitosan‐graft‐polyaniline composites with electromagnetic interference shielding properties: Synthesis,characterization, and curing kinetics

Conducting filler based on chitosan and grafted polyaniline (Ch‐g‐PANI) was prepared with different grafting ratios and used as fillers for polyester powder coating system. Differential scanning calorimetry is applied to study the effect of Ch‐g‐PANI on the curing of the polyester powder coating. The activation energy calculated by isoconversional Kissinger method was increased by either increasing the Ch‐g‐PANI content or the content of polyaniline in the filler, suggesting the contribution of the filler in the curing reactions. The cured samples were characterized using FTIR and TG analyses. Thermogravimetric analysis showed that the total thermal stability was enhanced upon the filler addition as detected from the values of integral procedural decomposition temperature. Furthermore, a dielectric study showed that the dielectric constant and loss were increased upon increasing of the filler. Vogel–Fulcher–Tammann equation was well‐fitted when used to examine the dependence of α‐relaxation on the temperature and the dielectrically calculated T_g values were comparable to that measured by DSC. The shielding effectiveness toward microwaves was enhanced by increasing the filler content. POLYM. ENG. SCI., 59:372–381, 2019. © 2018 Society of Plastics Engineers