Eco‐friendly durable press finishing of cellulose‐containing fabrics

To impart easy‐care properties to cellulose‐containing fabrics along with avoiding any harmful effects of formaldehyde on both the health and the environment, attempts have been made to use citric acid (CA) as an ester crosslinking agent along with different catalytic systems in the absence and presence of certain additives. Further, fixation conditions, type of crosslinking agent, as well as type of substrate have been studied. Results revealed that the enhancement in carboxyl content, performance properties, and the decrease in tear strength (TS) as well as in whiteness indices (WI) of the finished fabric samples were increased by increasing CA concentration up to 80 g/L and by raising thermofixation temperature from 140 up to 180°C for 90 s. Inclusion of triethanolamine hydrochloride (TEA. HCl), decreased the carboxyl content, TS, color strength K/S, as well as oily stain release rating (SRR) of the finished fabric samples along with an increase in bound nitrogen (%N), wrinkle recovery angle WRA, and an improvement in WI without affecting the durable press rating (DP). Within the range examined (0–30 g/L), increasing PEG‐600 concentration improved the wet resiliency, TS, as well as WI properties of the finished samples. Increasing DMDHEU ratio in the CA/DMDHEU crosslinking system gave rise to an increase in %N, WRA (dry and wet), DP, as well as in free CH₂O of finished fabrics, along with a slight improvement in WI values. On the other hand, the TS, carboxyl content, K/S, SRR values of the finished fabric samples were lower at a higher DMDHEU ratio. Increase in carboxyl content, %N, WRA (dry and wet), DP and SRR, as well as extent of post dyeing (K/S) of the treated fabric samples upon using different ester crosslinking agents followed the descending order: citric acid > pyromellitic dianhydride. The opposite holds true for the TS, and WI values. Among the esterifying catalysts used, and for a given set of finishing conditions, NaH₂PO₂ · H₂O proved to be the most effective one, and the following order of effectiveness may be drawn: NaH₂PO₂ · H₂O > K₂HPO₄ > Na₃–citrate > Na₂–tartrate. Inclusion of silicone softener in the finishing formulation brought about an improvement in softeness degree, WRA, %N, DP, TS as well as K/S values along with a decrease in carboxyl content, SRR, and WI values of the treated fabric samples, regardless of the used silicone softener.The performance properties of the finished fabric samples were determined by the type and nature of the substrate. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2243–2253, 2002     

Synthesis,characterization, and thermal properties of phosphorus‐containing,wholly aromatic thermotropic copolyesters

A series of phosphorus‐containing, wholly aromatic thermotropic copolyesters from acetylated 2‐(6‐oxide‐6H‐dibenz〈c,e〉〈1,2〉oxa phosphorin‐6‐yl)‐1,4‐dihydroxy phenylene, p‐acetoxybenzoic acid, terephthalic acid, and isophthalic acid were prepared by melting polycondensation. The structure and basic properties of the polymers, such as the glass‐transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity, were investigated with Fourier transform infrared, elemental analysis, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray diffraction, and hot‐stage polarizing optical microscopy. The copolyesters had relatively high T_g values ranging from 183 to 192°C. The T_m values obtained from DSC curves for samples P‐20 and P‐25 were 290 and 287°C, respectively (where the number in the sample name indicates the molar fraction of the phosphorus‐containing monomer in the reactants). The initial flow temperatures of other samples observed with hot‐stage polarizing microscopy were 271–290°C. The 5% degradation temperatures in nitrogen ranged from 431 to 462°C, and the char yields at 640°C were 41–52%. All the copolyesters, except P‐40, were thermotropic and nematic. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1278–1284, 2002     

Poly(etherimide)/montmorillonite nanocomposites prepared by melt intercalation

A novel aromatic amine organo‐modifier synthesized in our previous work was used to treat montmorillonite (MMT) and the organo‐modified MMT was used to prepare poly(etherimide) (PEI)/MMT nanocomposites by a melt intercalation method. MMT treated by this amine exhibited large layer‐to‐layer spacing and a high ion‐exchange ratio (>95%). The nanocomposites were characterized with X‐ray diffraction (XRD), transmission electron microscopy (TEM), dynamic mechanical analysis, a universal tester, thermogravimetric analysis, and by differential scanning calorimetry. The results of XRD and TEM showed that the nanocomposites formed exfoliated structures even when the MMT content was 10 wt %. When the MMT content was below 3 wt %, the PEI/MMT nanocomposites were strengthened and toughened at the same time. The nanocomposites also showed marked decreases in coefficient of thermal expansion and solvent uptake. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1857–1863, 2003     

Fabrication of Porous SiC Ceramics with Special Morphologies by Sacrificing Template Method

Sacrificial template technique is widely used in producing porous materials with controlled morphologies and tailored properties. In this paper, unique templates such as filters, carbon nanotube, carbon fiber and silica were used to make porous SiC ceramic with special morphologies. Template derived porous ceramic plates, SiC nano-net, fiber-inverse and bead-inverse porous SiC ceramic were successfully prepared from the preceramic precursor, polymethylsilane (PMS). The synthesis procedures were involved with the infiltration of the templates with appropriate concentration of the preceramic polymer, their curing, pyrolysis and subsequent template removal. The synthesized porous SiC was characterized by SEM, TEM, XRD and BET methods.     

Antimicrobial protection of cotton and cotton/polyester fabrics by radiation and thermal treatments. I. Effect of ZnO formulation on the mechanical and dyeing properties

Cotton and cotton/polyester fabrics were treated against microbial attack by applying a formulation based essentially on ZnO under high‐energy radiation and thermal curing. To achieve the homogeneity and the reactivity of the treating formulation, a binder (Impron MTP) and a dispersing agent (Setamol WS) were used with ZnO. The antimicrobial property of the fabrics was evaluated, in terms of mechanical properties, by a soil burial test. Moreover, the effect of antimicrobial finishing on the dyeing properties in terms of color strength was investigated. It was found that the best composition that affords the best antimicrobial protection to cotton fabrics contains 2% ZnO, 2% binder, and 1% dispersing agents. For the cotton/polyester blend, the best results were achieved at the same conditions except the ZnO was 1%. It was found that the treatment under the effect of electron‐beam irradiation is better than that of gamma irradiation and thermal curing. The results showed that when the finishing process was carried out before dyeing with a reactive dye, it affects the color strength rather than performing the finishing after the dyeing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1129–1137, 2003     

Preparation of ketoprofen‐loaded high‐molecular‐weight poly(vinyl alcohol) gels

High‐molecular‐weight atactic poly(vinyl alcohol) (a‐PVA) gels loaded with (R,S)‐2‐(3‐benzoylphenyl)propionic acid (ketoprofen) were prepared from 5, 6, 7, and 8 g/dL solutions of a‐PVA with a number‐average degree of polymerization of 4000 in an ethylene glycol/water mixture with an aging method to identify the effect of the initial polymer concentration on the swelling behavior, morphology, and thermal properties of a‐PVA gels. Then, the release behavior of ketoprofen from a‐PVA gels was investigated. As the polymer concentration decreased, the ability for network formation decreased, and the degree of swelling of the a‐PVA gels increased. In addition, the enthalpy increased with an increase in the a‐PVA concentration, but the melting temperatures of the gels prepared at different initial polymer concentrations were the same; this indicated that tighter gel networks would be formed by a higher polymer chain density. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

A study on crystallization kinetics of pentaerythritol in a batch cooling crystallizer

The crystallization kinetics of pentaerythritol (PeE) in aqueous solution in the presence of impurity or not in a batch cooling crystallizer was explored. Also, the solubility and the nucleation and crystal growth kinetics of PeE in aqueous solution were investigated. A second-order dependence of PeE growth rate on supersaturation is observed in pure PeE-water system. The crystal growth rate of PeE-water system in the presence of impurity is proportional to the supersaturation to the 3.5 power. The nucleation and crystal growth behaviors for PeE-water system in a batch cooling crystallizer were grasped according to Mersmann's criteria. The nucleation in this crystallizer was found to act with heterogeneous nucleation. In this system, it suggests that the crystal growth is controlled by a complex mechanism behavior of surface integrated and diffusion limited. Simplified relation was derived for calculation of mean crystal size of product crystals from the batch cooling crystallizer. The obtained relation was verified by a set of experiments.     

Selective Oxidation of Methanol to Formaldehyde Using Modified Iron-Molybdate Catalysts

Methanol selective oxidation to formaldehyde over a modified Fe-Mo catalyst with two different stoichiometric (Mo/Fe atomic ratio = 1.5 and 3.0) was studied experimentally in a fixed bed reactor over a wide range of reaction conditions. The physicochemical characterization of the prepared catalysts provides evidence that Fe₂(MoO₄)₃ is in fact the active phase of the catalyst. The experimental results of conversion of methanol and selectivity towards formaldehyde for various residence times were studied. The results showed that as the residence time increases the yield of formaldehyde decreases. Selectivity of formaldehyde decreases with increase in residence time. This result is attributable to subsequent oxidation of formaldehyde to carbon monoxide due to longer residence time.     

Rheological properties of ethylcellulose latex

Because of their large specific surface area, aqueous‐based pseudolatex systems of ethylcellulose can absorb large amounts of drugs. In addition, the stability of polymeric particles in biological fluids delays the release of the drug as in controlled drug delivery systems. The aim of the present study was to characterize the rheological properties of latex particles as a measure of their colloidal stability. Here, we report the effect of three variables: pH, electrolyte concentration, and temperature. The rheograms clearly show that the polymer suspensions displayed Bingham plastic behavior. Internal structuring of the latex was greatest at acid and natural pH values, particularly at the highest ionic strength. In acid solutions, only temperature appeared to play a fundamental role; both the shear stress corresponding to the onset of nonlinear viscoelasticity and the elastic modulus at all frequencies were higher at 37°C than those at room temperature. This is assumed to be a consequence of deformation of the polymer particles upon heating. The effect of ionic strength was noticeable only at the natural pH (pH ? 6.5). At high concentrations of sodium chloride, the particles aggregated because of the decrease in double layer repulsion, and as a result, the latex became structured and its elastic modulus subsequently increased. Interestingly, when the temperature was increased further, this structure presumably broke, down, at least partially, and the storage modulus was reduced. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 847–851, 2006     

Shear creep resistance of styrene–isoprene–styrene (SIS)‐based hot‐melt pressure‐sensitive adhesives

The effects of the properties of substrates and tackifier on the shear creep of SIS‐based HMPSAs were investigated. The holding power (t_b) and shear adhesion failure temperature (SAFT) were measured. The relationship between the complex viscosity and the holding power was examined. The holding power and SAFT values of the triblock SIS blends were higher than those of the diblock‐containing SIS blends, perhaps because blends using triblock SIS have higher crossover temperature and complex viscosity than those using diblock‐containing SIS. Higher levels of aromatic resin‐modified aliphatic tackifier and rosin ester were found to decrease the holding power of the HMPSAs. This maybe due to the fact that rosin ester and aromatic‐modified aliphatic resin are compatible with both the ends and midblocks of SIS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 825–831, 2006