Characteristics of membrane humidifiers for polymer electrolyte membrane fuel cells

Water management plays an important role in obtaining high performance from a polymer electrolyte membrane fuel cell (PEMFC). To reduce the volume and energy consumption of widely-used bubble humidifiers, membrane humidifiers were fabricated by using an ultrafiltration (UF) membrane and Nafion membranes. The performance of the membrane humidifiers was examined as a function of gas flow rate and operating temperature. A single cell was operated using the UF membrane humidifiers exhibiting almost the same performance with that employing bubble humidifiers.     

Rotational diffusion coefficient of rod-like polymer with a slight flexibility in semidilute and concentrated solutions

Summary A confined stiff chain model is suggested for the prediction of the rotational diffusion coefficient of a rigid rodlike polymer with a slight flexibility above the region of dilute solution (c1/L³). It shows a fairly good agreement with the experimental data of various polymers. Among them, PBLG and PBT with more rigidity are more consistent with the model when the log-jamming effect is considered. The predicted rotational diffusivity shows approximately the inverse seventh-power of length, which is less than 9 of Doi-Edwards tube model, but larger than the experimental value 5.7 of M-virus, while it shows the inverse power of concentration is a little larger than the value 2 of tube model except for the rodlike virus M-13.     

Numerical and experimental study on the biofiltration of toluene vapor

We have solved both steady state and transient problems on the biofiltration of toluene vapor. The effect of inlet toluene concentration and inlet gas-flow rate on the removal rate of toluene and the elimination capacity of a lab-scale biofilter has been investigated. In this study, the effectiveness factor was a function of pollutant concentration. The dynamic solutions show good agreement with experimental results. At an inlet toluene concentration of 100 ppm, the diffusion of toluene into biofilm was obviously a rate determining step. Above 200 ppm, however, biofilm already showed full activity. The steady-state simulation confirmed that the change of elimination capacity obtained by increasing only inlet toluene concentration was the same as that obtained by increasing only flow rate of contaminated air. The maximum possible performance is about 20 g/m³h with no addition of nutrients.     

Preparation and characterization of polypropylene/layered silicate nanocomposites using an antioxidant

Polypropylene (PP)/layered silicate nanocomposites were prepared via simple melt mixing of three components, PP, layered silicates modified with octadecylamine (C18-MMT) and antioxidant, to investigate the role of antioxidant. TEM and X-ray scattering results confirmed the intercalated state of silicates in PP/layered silicate nanocomposites with antioxidant. In rheological and mechanical study, the nanocomposites with antioxidant showed higher properties than those of the unfilled PP. The nanocomposite with 5 wt% C18-MMT and 0.5 phr antioxidant exhibited about 1.4 times higher tensile modulus and 1.3 times higher storage modulus than the unfilled PP. However, PP/C18-MMT without antioxidant showed lower rheological values owing to the thermal decomposition of PP and the poor compatibility between PP and C18-MMT. It could be concluded that antioxidants played an important role in enhancing the compatibility between PP and C18-MMT. According to the real time X-ray diffraction, the nanocomposite showed the weak ordering of PP crystals than the unfilled PP in the load-extension plateau region of elongation.     

Effects of Acetic Acid on the Crystallization Temperature of Sol–Gel-Derived MgO Nano-Powders and Thin Films

The influences of acetic acid addition to Mg-methoxide on the stability of the precursor and the crystallization behavior of sol–gel-derived MgO nano-powders and thin films were investigated using X-ray powder diffraction, transmission electron microscopy, Fourier-transformed infrared spectroscopy, and thermogravimetry. The addition of acetic acid enhanced the stability of the alkoxide against precipitation. Moreover, during postheat treatment of the gel powders treated with acetic acid, a significantly lowered crystallization temperature (250°C) was observed as compared to the untreated counterpart (350°C). The low-temperature crystallization of MgO, induced by the modification of Mg-methoxide with acetic acid, was related to the decomposition of organics at a lower temperature. These results could be explained in terms of the decrease of the O–R bond strength depending on the increase in the alkyl group size. MgO thin films having a high degree of crystallinity were successfully obtained from the Mg-methoxide treated with acetic acid at 300°C. The low-temperature crystallization of sol–gel-derived MgO thin films showed the feasibility for their application as a protective layer in alternative current plasma display panel cells.     

Preparation and electrical properties of metal sulfides–amidoximated PAN composite film

To improve the electrical conductivity of polyacrylonitrile (PAN) film, metallic sulfides and PAN composite film were prepared by the chelating method. Dense PAN film and porous PAN film were prepared by dry process and wet process, respectively. These PAN films were treated to NH₂OH solution to introduce the amidoxime group coordinated with metallic ion. Cu⁺² and Cd⁺² ions were adsorbed to amidoximated PAN films, the sulfur ion was treated with metal-adsorbed PAN films, and thus CuS—and CdS–PAN composite films were prepared. The adsorptive capacity of amidoximated PAN film for the Cu⁺² ion was independent of the morphology of the PAN film, but the adsorptive capacity of the Cd⁺² ion on amidoximated PAN film was dependent on porosity of the polymer. Adsorptive capacity of amidoximated porous PAN film for Cd⁺² was improved about four times than that of amidoximated dense PAN film. The electrical conductivities of CuS–dense and porous PAN composite film were both 10^?1 S/cm in optimum condition, but because of the difference in adsorptive capacity, the electrical conductivities of CdS–dense and CdS–porous PAN composite films were 10^?9 S/cm and 10^?4 S/cm, respectively. Additionally, because CdS was known as a photoconductive material, the photoconductive properties of CdS–porous PAN composite film were investigated.     

Effect of reactive diluents on properties of unsaturated polyester/montmorillonite nanocomposites

Unsaturated polyester (UP)/montmorillonite (MMT) nanocomposite was prepared by using hydroxypropylacrylate (HPA) as a reactive diluent instead of conventional styrene monomer and the effect of polarity of reactive diluent on properties of nanocomposite was investigated. X‐ray and mechanical test data indicated that mixing for an extended period of time is essential to enhance the physical properties of nanocomposites in the UP/Cloisite 6A system. This was attributed to the high polarity of HPA that may disturb the preintercalation of UP resin into the galleries of MMT. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 238–242, 2004     

Electrical properties of (Bi3.5La0.5)Ti3O12 thin-films prepared by liquid source misted chemical deposition

The ((Bi_3.5La_0.5)Ti₃O₁₂(BLT) thin-films used in this study were fabricated on a Pt(111)/SiO₂/Si(100) substrate by a Liquid Source Misted Chemical Deposition (LSMCD) technique. X-ray diffraction patterns showed that the BLT films were crystallized and no other phases were observed when annealed above 650 ‡C. Grain size and remnant polarizations increased with increase in the annealing temperature, while leakage current densities decreased. The remnant polarizations (Pr) increased from 2.0 to 4.8 and 19.0 μC/cm2 with increase in the annealing temperature from 650 to 700 and 750 ‡C, respectively. The BLT films annealed at 700 ‡C in O₂ showed a good fatigue resistance of reduced polarization by 10% after 10⁹ switching cycles when 9 V of bipolar voltage was applied at a frequency of 40 kHz.     

Fabrication of SiO2-ZrO2 composite fiber mats via electrospinning

(1 − x)SiO₂-(x)ZrO₂ (x = 0.1, 0.2) composite fiber mats were prepared by electrospinning their sol-gel precursors of zirconium acetate and tetraethyl orthosilicate (TEOS) without using a polymer binder. The electrospun composite fibers were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FT-IR) and mercury porosimetry. The composite fibers having a tetragonal crystalline ZrO₂ were obtained by calcining the electrospun composite fibers at high temperatures. The results show that the structure and crystallization of ZrO₂ in the composite fibers can be controlled by sintering temperature, while the porosity and morphology of the fiber mats did not depend on the sintering temperature.     

Defect detection using feature point matching for non-repetitive patterned images

Defect detection is an important technology for the quality control in the production process of wafer, TFT-LCD and PCB. Inspection is performed using the finished product’s image. The images are classified into two different groups—images with a repetitive pattern on a regular cycle and images without a repetitive pattern. A standard object for comparison is required, because manual defect detection is not possible for areas without repetitive patterns. In such areas, defect detection occurs through contrasting a reference pattern to the pattern being inspected. Methods of inspection using reference image have been researched but have limitations due to their requirement of precise alignment of the images. This paper proposes a method of defect detection to overcome such limitation using feature point matching. Feature points are extracted using a corner detector and detects defect by finding a correspondence between two feature point sets. Performance of the proposed method is evaluated by using Wafer SEM images and compared with conventional methods. Experiment results demonstrate the proposed method achieves higher detection accuracy than conventional methods and is less sensitive to alignment error and noise.