The Effect of Deformation Heating on Restoration and Constitutive Equation of a Wrought Equi-Atomic NiTi Alloy

In this study, a set of constitutive equation corrected for deformation heating is proposed for a near equi-atomic NiTi shape memory alloy using isothermal hot compression tests in temperature range of 700 to 1000 °C and strain rate of 0.001 to 1 s⁻¹. In order to determine the temperature rise due to deformation heating, Abaqus simulation was employed and varied thermal properties were considered in the simulation. The results of hot compression tests showed that at low pre-set temperatures and high strain rates the flow curves exhibit a softening, while after correction of deformation heating the softening is vanished. Using the corrected flow curves, the power-law constitutive equation of the alloy was established and the variation of constitutive constants with strain was determined. Moreover, it was found that deformation heating introduces an average relative error of about 9.5% at temperature of 800 °C and strain rate of 0.1 s⁻¹. The very good agreement between the fitted flow stress (by constitutive equation) and the measured ones indicates the accuracy of the constitutive equation in analyzing the hot deformation behavior of equi-atomic NiTi alloy.     

Experimental and theoretical study of density jumps on smooth and rough beds

Hydraulic jumps in density currents are technically referred to density jumps. These jumps significantly influence the dynamic and quality characteristics of the gravity currents. The density jump is studied theoretically and experimentally in this study by considering the bed roughness. Experiments were performed in a rectangular laboratory flume (0.4 m width; 0.9 m depth; 8.3 m length). Four rough beds comprised of closely packed gravel particles glued onto the horizontal part of the bed were examined. For both smooth and rough beds, a simple relationship was obtained for estimating the conjugate depth ratio as a function of the relative roughness and the upstream densimetric Froude number. The conjugate depth ratio was found to decrease with increasing relative roughness. The results also indicated that, if the entrainment ratio is specified, the minimum value of the upstream densimetric Froude number increases with increasing relative bed roughness. An equation for calculating the maximum possible value of the relative roughness was also determined. The spatial development of the density current for smooth beds was analysed in both super‐critical and sub‐critical flow regimes. Good similarity collapses of velocity and concentration profiles were obtained for the super‐critical section just upstream of the jump. The concentration distributions located just downstream of the jump, however, exhibited a large scattering of measured data, especially near the bed. It was found that this scattering decreases with the distance from the end of the jump. The results of the experimental runs also indicated that, at a distance about nine times the post‐jump current thickness from the end of the jump, the non‐dimensional vertical profile of mean velocity has a shape similar to that at the pre‐jump section. A new reliable relationship was also proposed for calculating the local velocity inside both the wall and jet regions.     

Parametric estimation of change-points for actual event data in recurrent events models

Time to event data have long been important in many applied fields. Many models and analysis methods have been developed for this type of data in which each sample unit experiences at most a single end-of-life event.In contrast, many applications involve repeated events, where a subject or sampling unit experiences more than one event. There is growing interest in the analysis of recurrent events data, also called repeated events and recurrence data. This type of data arises in many fields. For example, the repair history of manufactured items can be modeled as recurrent events. In medical studies, the times of recurrent disease episodes in patients can also be modeled as recurrent events. In this paper we focus on medical applications (e.g. seizures, heart attacks, cancerous tumors, etc.). However, our proposed methodologies can be applied to other areas as well.For analyzing recurrence data, the first and perhaps most important step is to model the expected number of events, and sometimes this can be facilitated by modeling the cumulative intensity function or its derivative, the intensity rate function. One particular recurrent events scenario involves patients experiencing events according to a common intensity rate, and then a treatment may be applied. Assuming the treatment to be effective, the patients would be expected to follow a different intensity rate after receiving the treatment. Further, the treatment might be effective for a limited amount of time, so that a third rate would govern arrivals of the recurrent events after the effects of the treatment wore out. In this paper we model the intensity rate for such scenarios. In particular we allow models for the intensity rate, post-treatment, to be piecewise constant. Two estimators of the location of this change are proposed. Properties of the estimators are discussed. An example is studied for illustrative purposes.     

A new blend of polymeric encapsulation of azithromycin by spray-drying with a pH responsive in drug release

The microencapsulation of macrolides with polymers has been reported to retard the release of the drug in oral cavity. However, these methods are unable to control drug release in gastrointestinal tract. The aim of the present study was to investigate the effect of formulation of a new polymeric encapsulation of azithromycin which is suitable for both masking and sustained release usage. Eudragit E100 and polyethylene glycol (PEG) 4000 were chosen as the barrier coatings. The spray drying technique was used to obtain the microcapsules containing azithromycin. To obtain the initial results, the effects of several parameters were evaluated. A 3:2:1 ratio of E100:PEG 4000:azithromycin at pH 6 gave the best coating condition. Thermogravimetric analysis and IR analysis data confirmed the encapsulation of azithromycin inside polymers. The encapsulated drug was released in different rates from the particles by changing the pH (1.7 and 7.4). An analysis of the kinetic release properties indicates that the release of the drug is a combination of swelling and diffusion mechanism. The synergistic cooperation between polymers and drug due to the existence of several hydrogen bonding is supposed to influence the pH-responsive property of the encapsulated drug. Moreover, the use of mixtures of E100 and PEG 4000 appears to offer a good balance between cost and efficiency.     

Gas-phase transport and entropy generation during transient combustion of single biomass particle in varying oxygen and nitrogen atmospheres

Transient combustion of a single biomass particle in preheated oxygen and nitrogen atmospheres with varying concentration of oxygen is investigated numerically. The simulations are rigorously validated against the existing experimental data. The unsteady temperature and species concentration fields are calculated in the course of transient burning process and the subsequent diffusion of the combustion products into the surrounding gases. These numerical results are further post processed to reveal the temporal rates of unsteady entropy generation by chemical and transport mechanisms in the gaseous phase of the reactive system. The spatio-temporal evolutions of the temperature, major chemical species including CO, CO₂, O₂, H₂ and H₂O, and also the local entropy generations are presented. It is shown that the homogenous combustion of the products of devolatilisation process dominates the temperature and chemical species fields at low concentrations of oxygen. Yet, by oxygen enriching of the atmosphere the post-ignition heterogeneous reactions become increasingly more influential. Analysis of the total entropy generation shows that the chemical entropy is the most significant source of irreversibility and is generated chiefly by the ignition of volatiles. However, thermal entropy continues to be produced well after termination of the particle life time through diffusion of the hot gases. It also indicates that increasing the molar concentration of oxygen above 21% results in considerable increase in the chemical and thermal entropy generation. Nonetheless, further oxygen enrichment has only modest effects upon the thermodynamic irreversibilities of the system.     

Comparison of the Activation Energies of the Formation of Chromium Carbide Coating on Carburized and Uncarburized AISI 1020 Steel

Chromium carbide coatings deposited by the salt bath method have a lot of technologically interesting characteristics. This method produces hard, wear–resistant, oxidation and corrosion–resistant coating layers on steel substrates. In the present study, the kinetics of chromium carbide formation on carburized and uncarburized AISI 1020 steel substrates has been compared. The presence of the Cr₇C₃ phase on the surface of steel substrates was confirmed by X‐ray diffraction. Cross–sectional observation of optical and SEM images showed that chromium carbide layers formed on the steel substrates were rather compact and smooth. The kinetics of chromium carbide coating by salt bath immersion indicated a parabolic relationship between carbide layer thickness and treatment time. The activation energy of the formation of carbide on the surface of carburized and uncarburized steel was calculated to be 87.9 and 225.6 kJ/mol, respectively. Moreover, an attempt was made to present contour diagrams for predicting the thickness of the chromium carbide layer. In addition, the possibility of establishing and using some mathematical relationships between process parameters and chromium carbide layer thickness was investigated.     

Numerical and experimental investigation of vortex breaker effectiveness on the improvement in launch vehicle ballistic parameters

The focus of the present study is to investigate the effectiveness of installing vortex breakers at the outlet of launch vehicle tanks on postponing vortex formation and decreasing the critical height of propellants while discharging. Analytical results in the absence of a vortex breaker show that the effects of the Weber and Reynolds numbers in the flow field can be ignored for values greater than 720 and 1.1 × 10⁵, respectively; and critical height can be considered as a function of Froude number under aforementioned conditions. The analytical criteria are verified by two-dimensional, axis symmetrical, transient and two-phase numerical model. Eventually, some experiments are conducted to examine the effectiveness of the applied vortex breakers in reduction of the critical height of propellant. Experimental results show that a 30% decrease can be achieved in critical height by using a particular type of vortex breaker. Additionally, the carried out simulations for an existing two-stage launch vehicle indicate a 13% increase in orbital altitude, which in turn proves the considerable improvement in launch vehicle mass/energetic capabilities.     

Evaluation of Lepidium sativum seed and guar gum to improve dough rheology and quality parameters in composite rice–wheat bread

The effects of hydrocolloids in rice–wheat flour were studied. Hydrocolloids at 0%, 0.3%, 0.6% and 1% w/w (flour basis) and guar (G), Lepidium sativum seed (L) and guar-L. sativum seed (GL) gum were tested as additives to the rice/flour in various combinations. The quality parameters for the experiment were assessed with farinography, extensography, amylography and texture profile analysis. The evaluation of dough rheology showed that water absorption, dough development time, dough stability and viscosity all increased with the addition of hydrocolloids alone or in a combination. It was demonstrated that G₁L₁ promoted the highest effect. The mixing tolerance index and gelatinization temperature decreased with an increased hydrocolloid concentration. Extensibility value for the dough that incorporated guar and L. sativum seed gum increased with increasing hydrocolloid concentration from 0.3% to 0.6% and then decreased at 1%. The water activity of all bread didn't have significant differences with increasing hydrocolloids concentration but this parameter 24 decreased during storage. Firmness decreased with increasing hydrocolloid concentration and increased with increasing storage time. The sensory evaluation by a consumer panel gave the higher score for overall acceptability to G_0.3L_0.3 and G_0.3L_0.6 samples. The results also showed that G₁L₁, G₁L_0.6 and G_0.6L₁ samples had high specific volume and porosity.     

Thermal cracking and combustion kinetics of asphaltenes derived from Fosterton oil

Thermal behavior of crude oil (Fosterton) asphaltenes mixed with reservoir sand was investigated using thermogravimetric analysis (TGA), in nitrogen and air atmospheres for different heating rates up to 800 °C. In this study, four sets of TGA runs were performed to examine the thermal behavior of Fosterton asphaltenes and the coke derived from the asphaltenes. The parameters studied were heating rate (10, 15 and 20 °C min^− 1) and the type of purge gas (N₂ and air) employed for the process of thermal degradation of asphaltenes. Distributed activation energy model (DAEM) has been applied to study the asphaltene pyrolysis kinetics. It was observed that the activation energy was distributed from 46.16 to 72.17 kJ/mol, for the conversion range of 0.1 to 0.4. The general model for nth order reaction was used to obtain the kinetic parameters of coke oxidation reaction from the TGA data. From the model, the calculated activation energy, E, was 93.46 kJ/mol and the pre-exponential factor was 9.59 × 10⁵ min^− 1 for the coke combustion. The apparent order of combustion reaction gradually increased from 0.7 to 0.8 for different temperatures.