Radiation-induced polymerization of ethylene in pilot plant. III. Heavy-phase recycling process

Radiation-induced polymerization of ethylene using aqueous tert-butyl alcohol as medium was carried out in a large-scale pilot plant with a 50-liter central source-type reactor at a pressure of 105 to 395 kg/cm², temperature of 30° to 80°C, mean dose rate of 4.5 × 10⁴ to 1.9 × 10⁵ rads/hr, ethylene feed rate of 5.5 to 23.5 kg/hr, and medium feed rate of 21 to 102 l./hr. The space–time yield and molecular weight of the polymer were in the range of 4.7 to 16.8 g/l.-hr and 1.3 × 10⁴ to 8.9 × 10⁴, respectively. The space–time yield and molecular weight increased with mean residence time at 30°C, whereas at 80°C they became almost independent of the time. The space–time yield increased with pressure and dose rate, slightly decreased with temperature, and was maximum at ethylene molar fraction of 0.5. The polymer molecular weight increased with pressure and ethylene molar fraction, and decreased with dose rate and temperature. The total amount of deposited polymer on the reactor wall, source case wall, and scraping blades was usually less than 1 kg, which was negligibly small for the analysis of polymerization. Continuous discharge of the polymer slurry and production of fine-powder polyethylene were successfully carried out. In the central source-type reactor, a dose rate of 1.9 × 10⁵ rads/hr was obtained with a ⁶⁰Co source of ca. 12 kCi.     

Development of flexible displays using back‐channel‐etched In–Sn–Zn–O thin‐film transistors and air‐stable inverted organic light‐emitting diodes

We developed flexible displays using back‐channel‐etched In–Sn–Zn–O (ITZO) thin‐film transistors (TFTs) and air‐stable inverted organic light‐emitting diodes (iOLEDs). The TFTs fabricated on a polyimide film exhibited high mobility (32.9 cm²/Vs) and stability by utilization of a solution‐processed organic passivation layer. ITZO was also used as an electron injection layer (EIL) in the iOLEDs instead of conventional air‐sensitive materials. The iOLED with ITZO as an EIL exhibited higher efficiency and a lower driving voltage than that of conventional iOLEDs. Our approach of the simultaneous formation of ITZO film as both of a channel layer in TFTs and of an EIL in iOLEDs offers simple fabrication process.     

Playful training with augmented reality games: case studies towards reality-oriented system design

In this paper, we propose a reality-oriented augmentation approach to support training activities. The approach aims at adding new value and playful features to traditional training environments with keeping their original look-and-feel. For example, a game monitoring service enables to automatically record game events so that players can review a gaming process and strategy for soul-searching, or replay most impressive scenes to share the experience with others after the game finishes. Even several services are running on background, digital devices and services are seamlessly integrated to the game environment in unobtrusive way so that players can concentrate on training as usual. The concept can be applied to both traditional games (e.g., poker and the game of Go) and non-gaming activities (e.g., calligraphy and drumming). We developed four case studies on the concept: Augmented Reality Go, EmoPoker, Augmented Calligraphy and AR Drum Kit. We discuss design issues in the reality-oriented augmentation process based on user study results.     

High-aspect-ratio through-hole array microfabricated in a PMMA plate for monodisperse emulsion production

Microchannel (MC) emulsification is a promising technique for producing monodisperse emulsions consisting of highly uniform droplets. The authors developed a high-aspect-ratio microstructure (HARMST) made of poly(methyl methacrylate) (PMMA) as a new MC emulsification device. A PMMA straight-through MC array plate consisting of 31,250 through-holes with a 7.3 × 22.9-μm oblong section and a 200-μm depth was fabricated by a process of synchrotron radiation (SR) lithography and etching. Oblong MCs fabricated in a PMMA straight-through MC array were highly uniform with a coefficient of variation of less than 2%. The fabricated PMMA straight-through MC array plate was used to produce water-in-oil (W/O) emulsions. Monodisperse W/O emulsions with average droplet diameters of approximately 25 μm and a minimum coefficient of variation of 3.2% were produced via a hydrophobic PMMA straight-through MC array. The PMMA straight-through MC array plate also produced monodisperse W/O emulsions at droplet production rates of up to 1.7 × 10⁴/s. The PMMA straight-through MC array plates developed in this work are expected to expand the application field of emulsification using straight-through MC array plates, which have previously been made of single-crystal silicon.     

Fabrication of 5.8‐in. OTFT‐driven flexible color AMOLED display using dual protection scheme for organic semiconductor patterning

Abstract— A 5.8‐in. wide‐QQVGA flexible color active‐matrix organic light‐emitting‐diode (AMOLED) display consisting of organic thin‐film transistors (OTFTs) and phosphorescent OLEDs was fabricated on a plastic film. To reduce the operating voltage of the OTFTs, Ta₂O₅ with a high dielectric constant was employed as a gate insulator. Pentacene was used for the semiconductor layer of the OTFTs. This layer was patterned by photolithography and dry‐etched using a dual protection layer of poly p‐xylylene and SiO₂ film. Uniform transistor performance was achieved in the OTFT backplane with QQVGA pixels. The RGB emission layers of the pixels were formed by vacuum deposition of phosphorescent small molecules. The resulting display could clearly show color moving images even when it was bent and operated at a low driving voltage (below 15 V).     

Production of monodisperse water-in-oil emulsions consisting of highly uniform droplets using asymmetric straight-through microchannel arrays

This paper reports the production of monodisperse water-in-oil (W/O) emulsions using new microchannel emulsification (MCE) devices, asymmetric straight-through MC arrays that were hydrophobically modified. The silicon asymmetric straight-through MC arrays consisted of numerous pairs of microslots and circular microholes whose cross-sectional sizes were 10 μm. This paper primarily focused on investigating the effect of the osmotic pressure of a dispersed phase (Π_d) on MCE. This paper also investigated the effects of the type of continuous-phase oils and the dispersed-phase flux (J _d) on MCE. The dispersed phases were Milli-Q water and Milli-Q water solutions containing sodium chloride. The continuous phases were decane (as control), hexane, medium chain triacylglyceride (MCT), and refined soybean oil (RSO) solutions containing tetraglycerin monolaurate condensed ricinoleic acid ester (TGCR) as a surfactant. At Π_d of exceeding threshold, highly uniform aqueous droplets with coefficients of variation of less than 3% were stably generated via hydrophobic asymmetric straight-through MCs. Monodisperse W/O emulsions with average droplet diameters between 32 and 45 μm were produced using the alkane–oil and triglyceride–oil solutions as the continuous phase. This work also demonstrated that the hydrophobic asymmetric straight-through MC array had remarkable ability to produce highly uniform aqueous droplets at very high J _d of up to 1,200 L m⁻² h⁻¹.     

Usefulness of newly developed 99mTc-labeled STA-R12 for tumor imaging

We synthesized four new tumor imaging agents, 99mTc-labeled metalloporphyrins (99mTc-STA-R12, -STA-R21, -STA-RN101 and -ATN-12) for the tumor imaging. We compared the differences of tumor imaging potency among these agents in CDF1 mice implanted with colon 26 tumor. Tumor images with these agents were obtained by using digital gamma-camera (RC135-E, Hitachi, Tokyo) and the biodistributions were analyzed by computerized medical radionuclide imageanalyser (RP-200, Hitachi, Tokyo). The highest tumor organ ratio and the excellent tumor image were obtained by 99mTc-STA-R12 (13,17-Bispropanyl aspartic acid-3-ethenyl-8-[N,N',N",N"-tetrakis (carboxylmethyl-2,7,12,18-tetramethyl-porphyrinato]-manga nes e(III). The maximum concentration of 99mTc-STA-R12 in tumor tissue was observed at around 120 minutes after i.v. injection. On the contrary, the uptake rates of other organs and tissues such as liver, brain, muscle, lung, bone and blood continuously decreased. The rapid accumulation of STA-R12 in cancer tissue and the clearance from other tissue suggested a potential usefulness of this compound for tumor imaging agent.     

Evidence for a Jahn-Teller distortion of Cs2NaHoCl6 at 150 mK observed by X-ray diffractometry

By means of SR X-ray diffractometry, cooperative Jahn-Teller distortion as a structural phase transformation of the first kind is directly confirmed by a splitting of Laue spots. It is understood that the degenerate ground state of a nonmagnetic doublet (₃) of Ho³⁺ in a cubic Ho-elpasolite, Fm3m(O _h ⁵ ), at least above 600 mK, is lifted up by a distortion below 150 mK, which was predicted by a splitting of the NQR spectrum and anomalies in the specific heat and magnetic susceptibility. This structural transformation shows not only the lowest transition temperature up to now, but also the greatest hysteresis specified by a Schottky-type excitation. The magnitude of the relative distortion (1/1) has been roughly estimated to be on the 2.0 · 10^–3 order of magnitude, which is much larger than the predicted value obtained from a point charge approximation. The pecularities of this transition are discussed from the viewpoint that the general theory of a structural transformation, established convincingly at high temperatures could not be easily applied.     

Successful fabrication of bicrystal Si substrates for YBa2Cu3O7 − y Josephson junctions

Bicrystal Si(BiSi) substrates for grain boundary (GB) Josephson junctions (GBJJs) have been fabricated by a direct bonding technique using a hot press method. The fracture strength and structure of the bonding interfaces were investigated to obtain substrates suitable for the junctions. It was found that an increase in the pressure of the hot press improves the reproducibility of the GBJJs. YBa₂Cu₃O_{7 − y} GBJJs were successfully fabricated on Bi-Si substrates with a misorientation angle of 15 ° bonded under a pressure of 90 kgf cm⁻² at 1200 °C in a vacuum of ≈10⁻³ Pa. These junctions showed typical I-V curves described by the RSJ model. The Shapiro steps induced by millimetre wave irradiation of 101 GHz were clearly observed in the I-V curves up to 3 mV, corresponding to at least 1.5 THz (, where e is the unit charge, V the voltage and h Planck's constant).