Deposition of boron doped DLC films on TiNb and characterization of their mechanical properties and blood compatibility

Abstract

Diamond-like carbon (DLC) material is used in blood contacting devices as the surface coating material because of the antithrombogenicity behavior which helps to inhibit platelet adhesion and activation. In this study, DLC films were doped with boron during pulsed plasma chemical vapor deposition (CVD) to improve the blood compatibility. The ratio of boron to carbon (B/C) was varied from 0 to 0.4 in the film by adjusting the flow rate of trimethylboron and acetylene. Tribological tests indicated that boron doping with a low B/C ratio of 0.03 is beneficial for reducing friction (μ = 0.1), lowering hardness and slightly increasing wear rate compared to undoped DLC films. The B/C ratio in the film of 0.03 and 0.4 exhibited highly hydrophilic surface owing to their high wettability and high surface energy. An in vitro platelet adhesion experiment was conducted to compare the blood compatibility of TiNb substrates before and after coating with undoped and boron doped DLC. Films with highly hydrophilic surface enhanced the blood compatibility of TiNb, and the best results were obtained for DLC with the B/C ratio of 0.03. Boron doped DLC films are promising surface coatings for blood contacting devices.     

Fabrication of silicon nitride nanoceramics—Powder preparation and sintering: A review

Fine-grained silicon nitride ceramics were investigated mainly for their high-strain-rate plasticity. The preparation and densification of fine silicon nitride powder were reviewed. Commercial sub-micrometer powder was used as raw powder in the “as-received” state and then used after being ground and undergoing classification operation. Chemical vapor deposition and plasma processes were used for fabricating nanopowder because a further reduction in grain size caused by grinding had limitations. More recently, nanopowder has also been obtained by high-energy milling. This process in principle is the same as conventional planetary milling. For densification, primarily hot pressing was performed, although a similar process known as spark plasma sintering (SPS) has also recently been used. One of the advantages of SPS is its high heating rate. The high heating rate is advantageous because it reduces sintering time, achieving densification without grain growth. We prepared silicon nitride nanopowder by high-energy milling and then obtained nanoceramics by densifying the nanopowder by SPS.     

Collapse of partially corroded or worn pipe under external pressure

This paper is concerned with the effect of internal corrosion or erosion defects on the collapse of pipelines under external pressure. Experiments are conducted on SS-304 tubes with D/t's of 21.0 and 18.7 with axially uniform grooves of several thicknesses and angular spans of 6–60°. All specimens exhibited the classical ovalization mode of collapse with the grooved side being more deformed. For groove angles between 6° and 20° the collapse pressure decreases as the angle increases but remains essentially constant for angles between 20° and 60°. The collapse pressure was found to decrease with groove depth, reducing by nearly 50% when the groove depth reached 50% of the pipe wall thickness. The experiments were simulated numerically using both the custom computer code BEPTICO as well as an axially uniform finite element model. The predictions were found to follow closely the trends of the experimental results. The three dimensionality of grooves was examined using appropriate finite element models. It was found that grooves shorter than about 8D constitute local imperfections and accurate prediction of their effect on collapse pressure requires fully 3-D modeling. By contrast, grooves 10D long or longer behave essentially as “long” grooves and can be analyzed using 2-D models.     

Preparation and properties of biodegradable network poly(ester-carbonate) elastomers

Biodegradable elastomeric network poly(ester-carbonate)s were prepared from multifunctional aliphatic carboxylic acids such as tricarballylic acid (Y_t) or trimesic acid (Y) and polycarbonate diols (PCD) with molecular weights of 1000 and 2000 g/mol. Prepolymers prepared by a melt polycondensation were cast from dimethylformamide solution and postpolymerized at 270 °C for 40-80 min to form a network. The resultant films were transparent, flexible and insoluble in organic solvents. WAXS exhibited the crystalline peaks due to polycarbonate segments for the network films from PCD₂₀₀₀, while those from PCD₁₀₀₀ were amorphous. The tensile properties were determined for these network films at the temperatures 22, 30, 40 and 50 °C. These films showed elastomeric properties at all temperatures measured. The elongation at break was much higher for the films from PCD₂₀₀₀ (208-434%) than those from PCD₁₀₀₀ (40-120%), and decreased with increasing temperatures. The weight losses of the network films degraded in the buffer solution of Rhizopus delemar lipase at 37 °C increased with time, suggesting that these network films are biodegradable. The degradation rate of the network films from Y_t is faster than that from Y. The GPC curves showed that the lipase hydrolyzed both the ester linkages between Y or Y_t and PCD as well as polycarbonate moiety in the network polymer.     

Nitrogen chemistry in coal pyrolysis: Catalytic roles of metal cations in secondary reactions of volatile nitrogen and char nitrogen

The present review focuses on elucidating the chemistry of nitrogen release during coal pyrolysis, in particular, on making clear catalytic roles of inherent Ca and Fe ions in not only the partitioning of volatile-N to tar-N, HCN, NH₃ and N₂ but also the conversion of char-N to N₂.     

Effect of Lipase Activity and Specificity on the DAG Content of Olive Oil from the Shodoshima-Produced Olive Fruits

Olive oils have a higher relative diacylglycerol (DAG) content than other plant oils. The lipase in olive fruits is involved in DAG production and is directly related to the acidity of the olive oil. However, the lipase activity and positional selectivity have not been clarified. To investigate the properties of olive fruit lipase, olive fruits of the Mission variety harvested during mid-December of 2005 on Shodoshima Island (Japan) were stored at 20, 30 or 40 °C for 4 weeks. Changes in the acidity and acylglycerol content of the oils extracted from the stored fruits were analyzed. The acidity and DAG content of the olive oils increased due to triacylglycerol (TAG) hydrolysis during storage. sn-1,2-DAGs preferentially increased during the early stages of storage, indicating that the olive fruit lipase is enantioselective for the sn-3 position, while non-enzymatic isomerization of sn-1,2-DAGs was observed throughout the entire duration of storage. Kinetic analysis revealed that the enantioselectivity of olive fruit lipase for the sn-3 position was approximately four times greater than for the sn-1 position. The lipase was gradually inactivated at temperatures of 30 °C or higher, and the ratios of the rate constant for inactivation to TAG hydrolysis at the sn-3 position was 0.2, 13, and 23 at 20, 30, and 40 °C, respectively.     

Temperature measurements of turbid aqueous solutions using near-infrared spectroscopy

We report a method that uses near-infrared spectroscopy and multivariate analysis to measure the temperature of turbid aqueous solutions. The measurement principle is based on the fact that the peak wavelength of the water absorption band, with its center near 1440 nm, shifts with changes in temperature. This principle was used to measure the temperatures of 1 mm thick samples of aqueous solutions containing Intralipid (2%), which are often used as optical phantoms for biological tissues due to similar scattering characteristics. Temperatures of pure water and aqueous solutions containing glucose (100 mg/ml and 200 mg/ml) were also measured for comparison. For the turbid Intralipid solutions, the absorbance spectrum varied irregularly with time due to the change in scattering characteristics. However, by making use of the difference between the absorbance at 1412 nm and the temperature-independent absorbance at 1440 nm, we obtained SEPs (standard error of prediction) of 0.3 degrees C and 0.2 degrees C by univariate linear regression and partial least squares regression, respectively. These accuracies were almost the same as those for the transparent samples (pure water and glucose solution).     

Fabrication of laser induced periodic surface structure for geometrical engineering

The paper presents the highly ordered geometrical structures of laser induced periodic surface structure (LIPSS) in azobenzene urethane polymer (DR19 polymer) from 4-(N,N-dihydroxyethylamino)-4′-nitroazobenzene (Disperse red 19) with tolylene-2,4-diisocyanate (TDI). One or two regulated striped LIPSS was formed in confined spaces between surface relief gratings (SRG) induced by the s-polarized interfered beams. The pitch of LIPSS was one-half or one-third of SRG pitch. Standing wave with some selected mode between SRG in the surface waveguide is responsible for the formation of the regulated striped LIPSS. The crossed illumination of the interfered beams showed the waffle-like structure for s-polarization beam and the egg crate-like (ECL) structure for p-polarized beam. Photoinduced microscopic molecular ordering was also investigated. The linear polarized beam gave the large optical anisotropy in the polymer and the circularly polarized beam produced the chiral structure. The circular dichroism spectra showed the sharp peak due to the circular Bragg reflection from which the chiral pitch was evaluated.     

Heat and moisture balance simulation of a building with vapor-open envelope system for subtropical regions

Global warming and the resource depletion induced discussions on sustainable developments within the construction sector. Also the rapid urbanization in subtropical regions is becoming one of the most important global issues. Appropriate measures must be taken in such developments to avoid further damage to the environment. In this study, the heat and moisture balance simulation of building with a sustainable building envelope system for subtropical climate was proposed. In the moisture balance simulation the moisture buffering by the interior materials was taken into account. The prediction of moisture buffer value (MBV) of the interior finishing materials was attempted and validated by measurements. Subsequently, the whole building calculation was carried out and the contribution of the moisture buffering to the indoor comfort and energy consumption was investigated. The MBVs of the mineral-based materials were predicted with high accuracy. However, that of wood-based composite was much higher than the experimental value. In order to create a more accurate model, nonlinear moisture conductance should be accounted when modeling wood-based materials. The heating and cooling demand of a test house was 9.4 kWh/m² and 14.5 kWh/m², respectively. It was concluded that the utilization of the building envelope system has a high potential to provide sustainable houses in subtropical regions. In order to enhance both energy efficiency and indoor comfort of buildings in subtropical regions, there still is a strong need to develop a holistic method to find the optimum building design considering not only moisture buffering but also all the relevant factors. The presented model will be validated by in-situ measurements in the near future.     

A comparative study of ethanol production by Issatchenkia orientalis strains under stress conditions

The ability of 13 strains of multi-stress-tolerant Issatchenkia orientalis yeast to produce ethanol was examined under different stress conditions, including conditions of elevated H₂SO₄ and Na₂SO₄ concentrations and increased heat. The MF-121 strain produced a significant amount of ethanol after the incubation in acidic media containing high concentrations of salt, e.g., 50 g/l Na₂SO₄ at pH 2.0, or at high temperatures, e.g., 43°C, when compared with other strains.