Preparation and properties of silicone‐containing poly(methyl methacrylate) gels

Poly(methyl methacrylate) (PMMA) gels with varying amounts of silicone and solvent and constant amounts of crosslinker were prepared by solution free radical crosslinking copolymerization of methyl methacrylate (MMA), ethylene glycol dimethacrylate (EGDM), tetraethoxysilane (TEOS) and vinyltriethoxysilane (VTES) comonomer systems. They were then studied in benzene at a total monomer concentration of 3.5 mol L^?1 and 70 °C. The conversion of monomer, volume swelling ratio, weight fraction and gel point were measured as a function of the reaction time, silicone concentration and benzene content up to the onset of macrogelation. Structural characteristics of the gels were examined by using equilibrium swelling in benzene, gel fraction and Fourier‐transform infrared (FTIR) analysis. The morphology of the copolymers was also investigated by SEM. Based on the obtained results, it was concluded that the FTIR data did not have the capacity to show the presence of the VTES or TEOS moiety in these kinds of copolymers. On the other hand, the variation of weight fraction of gel, W_g, and its equilibrium volume swelling ratio in benzene, q_v, exhibited the same behaviour as that of MMA/EGDM copolymers. Also, the dilution of the monomer mixture resulted in an increase in the gel point and swelling degree and a decrease in the percent of conversion and gel fraction. Finally, TEOS is not an ideal silicone compound for reaction in the MMA/EGDM copolymerization system, whereas VTES is a suitable silicone comonomer for this system and it has been proved useful. Copyright © 2005 Society of Chemical Industry     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

Liposomal hamycin in the control of experimental aspergillosis in mice: effect of phosphatidic acid with and without cholesterol

Hamycin incorporated into liposomes containing phosphatidylcholine (SPC) and phosphatidic acid (PA) had reduced toxicity and an enhanced antifungal activity in experimental aspergillosis in balb/c mice. Incorporation of cholesterol into liposomes led to a dose dependent decrease in the toxicity of hamycin. The LD50 (mg/kg) of hamycin contained in SPC/cholesterol/PA (molar ratio 4:5:1) liposomes was 2.8 whereas that in SPC/PA liposomes (molar ratio 9:1) was 0.35. Although the free drug had little or no protective effect on the animals, those administered liposomal hamycin at an equivalent dose (0.1 mg/kg) in the absence of cholesterol (SPC/PA; molar ratio 9:1) showed 90% survival after seven days of therapy. On the other hand the presence of cholesterol in the carrier phosphatidic acid liposomes (SPC/cholesterol/PA; molar ratio 4:5:1) at a similar dose (0.1 mg/kg) led to a 60% survival over the same time period. Hamycin incorporation in phosphatidic acid liposomes both in the presence or absence of cholesterol was found to be effective in reducing the fungal load in lung, liver, spleen and kidney. Studies with distribution of hamycin in various tissues by HPLC showed a significant reduction in the concentration of the liposomal drug in circulation as compared to those seem after administration of free drug.     

Influence of the silicon surface treatment by plasma etching and scratching on the nucleation of diamond grown in HFCVD - a comparative study

A comparative study for the nucleation of diamond was carried out using surface treatment like (i) surface scratching with 1 μm diamond paste and (ii) surface etching using chlorine plasma at different RF powers (50, 100 and 150 W). Atomic force microscopic study shows variation in roughness from 31 nm to 110 nm. Scratching results in random scratches, whereas plasma etches a surface uniformly. Scanning electron microscopic observations show well faceted crystallites with a predominance of angular shaped grains corresponding to 〈100〉 and 〈110〉 crystallite surfaces for the scratched as well as plasma etched substrate. Surface etching at 150 W plasma power results in a better growth in comparison with 50 and 100 W plasma powers. Chlorine-radical is found responsible for the changes in the growth morphology. Raman spectroscopy shows a sharp peak at 1,332 cm⁻¹ and a peak at ∼1,580 cm⁻¹ for both samples.     

Signature analysis and defect detection in layered manufacturing of ceramic sensors and actuators

This paper presents the concept of a process signature for the use of online signature analysis and defect detection in the layered manufacturing (LM) of ceramic sensors and actuators. To achieve the high quality of parts built by the fused deposition of ceramics (FDC), an online process-monitoring system is implemented to detect the processing defects. Using a process signature extracted from the image of a layer captured by the monitoring system, an ideal image is created that is then compared to the original image to detect and identify the defects. Some results of signature analysis and defect detection for single-material and multi-material parts are also presented.Received: 22 July 1999, Accepted: 21 October 2001, Published online: 29 October 2003 Correspondence to: Mohsen A. JafariThis work was supported by the Office of Naval Research under grant # N-0014-96-1-1175. Ref. US Patent # S-5738817, April 14, 1998.     

Effect of carbon surface oxidation on platinum supported carbon particles on the performance of gas diffusion electrodes for the oxygen reduction reaction

The effect of carbon surface oxidation on platinum supported carbon particles (Pt/C) with nitric acid was investigated by cyclic voltammetry, electrochemical impedance spectroscopy, polarization experiments and chronoamperometry. Cyclic voltammograms, polarization curves and electrochemical impedance spectra showed that the treated catalyst had much larger active surface area and higher ionic conductivity than the untreated catalyst, and provided enhanced performance for oxygen reduction. The formation of acidic groups was examined by IR spectra. The Pt/C surface oxidation had a large effect on the performance of a gas diffusion electrode for oxygen reduction reaction.     

Synthesis and thermomechanical characterization of polyurethane elastomers extended with α,ω‐alkane diols

A series of polyurethane (PU) elastomers was prepared by the reaction of poly(?‐caprolactone) and 4,4′‐diphenylmethane diisocyanate, which was extended with a series of chain extenders (CEs) having 2–10 methylene units in their structure. The completion of the reaction was confirmed by Fourier transform infrared spectroscopy. The chemical structures of the synthesized PU samples were characterized with Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR spectroscopy, and the thermal properties were determined by thermogravimetric analysis, DSC, and dynamic mechanical thermal analysis techniques. The mechanical properties were also studied and are discussed. The thermogravimetric analysis and DSC analysis showed that CE length had a considerable effect on the thermal properties of the prepared samples. The dynamic mechanical thermal analysis and damping peaks were also affected by the number of methylene units in the CE length. The elastomer extended with 1,2‐ethane diol exhibited optimum thermal properties, whereas the elastomer based on 1,10‐decane diol displayed the worst thermal properties. Tensile strength and elongation at break decreased with increasing CE length, whereas hardness showed the opposite trend. The glass‐transition temperature moved toward lower temperatures with increasing CE length. The decrease in the glass‐transition temperature and tensile properties were interpreted in terms of decreasing hard segments and increasing chain flexibility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Rheumatic heart disease in India

A cross-sectional study was carried out in rural areas of Jawan Block, District Aligarh, Uttar Pradesh, India, covering a total population of 3760 drawn from 11 villages. The total number of confirmed cases of rheumatic heart disease was 24 with a prevalence rate of 6.4 per 1000 of the general rural population. The prevalence of rheumatic heart disease increased with age until the age of 25 years. Females were more prone to rheumatic heart disease compared to males. Socio-economic class had a direct impact on the occurrence of rheumatic heart disease.