Ionic liquid mediated nano-composite polymer gel electrolyte for rechargeable battery application

ABSTRACT

Nano-composite polymer gel electrolytes (NPGEs) based on polymer poly(vinylidene fluoride-co-hexafluoropropylene) PVdF-HFP, ionic liquid, 1-butyl-3- methylimidazolium bis(trifluoromethanesulfonyl)imide BMIMTFSI, Li-salt along with the addition of SiO₂ nanoparticles have been synthesized and characterized by various techniques. Prepared NPGEs show high room temperature ionic conductivity (~10^?3 S/cm) and have a wide electrochemical window (ECW) (~3.3–3.5 V). The galvanostatic charge/discharge profile was studied by sandwiching best performing NPGEs between a LiFePO₄ cathode and lithium metal anode. The specific discharge capacity of the cell (Li/NPGE/LiFePO₄) room temperature at 0.1C rate is found to be 138 mAh/g.     

Bulk free radical polymerizations of methyl methacrylateunder non-isothermal conditions and with intermediate additionof initiator: Experiments and modeling

Experimental data on the monomer conversion, x_m, and the weight average molecular weight, M_w, have been generated under several isothermal and non-isothermal conditions for the polymerization of methyl methacrylate in a rheometer-reactor assembly. The non-isothermal results, in particular, can be used to provide more stringent tests of kinetic models than isothermal data alone. A simple empirical model has been used to describe this system that accounts for the gel (Trommsdorff) and glass effects. The model involves only x_m and the temperature, and is quite general. The model parameters are tuned using only three sets of isothermal data. Good agreement is found between the experimental results and model predictions for a whole variety of experimental conditions, including non-isothermal operation and with intermediate addition of initiator. Because of its generality, this model is quite suitable for use for on-line optimizing control as well as for describing industrial reactors.     

Simulation of an industrial nylon 6 tubular reactor

A commonly used energy-efficient nylon 6 reactor is simulated under steady-state conditions. The effects of various operating conditions and parameters, e.g., feed composition, temperature and flow rate, heat transfer coefficients, and reactor dimensions, on the temperature and molecular weight profiles are studied. A temperature maximum is observed in the reactor under usual conditions of operation. The maximum value of the temperature is sensitive to the feed conditions, and one has to ensure that degradation reactions speeded up at high temperatures do not affect product characteristics. The model and the numerical technique used are fairly simple and account for most of the important features of industrial reactors. Hence, these can be used in the development of digital-control algorithms in the future.     

Multivehicle coverage control for a nonstationary spatiotemporal field

This paper presents a multivehicle sampling algorithm to generate trajectories for nonuniform coverage of a nonstationary spatiotemporal field characterized by spatial and temporal decorrelation scales that vary in space and time, respectively. The sampling algorithm described in this paper uses a nonlinear coordinate transformation that renders the field locally stationary so that existing multivehicle control algorithms can be used to provide uniform coverage. When transformed back to the original coordinates, the sampling trajectories are concentrated in regions of short spatial and temporal decorrelation scales. For fields with coupled spatial statistics, i.e., the spatial decorrelation scales are functions of both spatial dimensions, the coordinate transformation is implemented numerically, whereas for decoupled spatial statistics, the transformation is expressed analytically. We show that the analytical transformation results in vehicle motion that preserves the vehicle sampling speed (which is a measure of vehicle speed scaled by the ratio of the spatial and temporal decorrelation scales), in the original domain; the sampling speed determines the minimum number of vehicles needed to cover a spatiotemporal domain. Theoretical results are illustrated by numerical simulations.     

In Situ Processing of Silicon Carbide Layer Structures

A novel route to low-cost processing of silicon carbide (SiC) layer structures is desribed. The processing involves pressureless liquid-phase cosintering of compacted power layers of SiC, containing alumina (Al₂O₃) and yttria (Y₂O₃ sintering additives to yield and yttrium aluminum garnet (YAG) second phase. By adjusting the β:α SiC phase ratios in the individual starting powders, alternate layers with distinctively different microstructures are produced: (i) "homogeneous" microstructures, with fine equiaxed SiC grains, designed for high strength; and (ii) "heterogeneous: microstructures with coarse and elongate SiC grains, designed for high toughness. By virtue of the common SiC and YAG phases, the interlayer interfaces are chemically compatible and strongly bonded. Exploratory Hertzian indetation tests across a bilayer interface confirm the capacity of the tough heterogeneous layer to inhibit potentially dangerous cracks propagating through the homogeneous layer. The potential for application of this novel processing approach to other layer architectures and other ceramic systems is considered.     

Chlorosis in sugarcane: Associated soil properties,leaf mineral composition,and crop response to iron and manganese

Attempts were made to find out the nature and cause of a widespread sugarcane chlorosis in a cane growing area. Soils from chlorotic and nonchlorotic fields did not differ markedly in pH, CaCO₃, electrical conductivity, organic C, and soil test P, Zn, Cu, and Mn levels, but the chlorotic field soils had relatively more NH₄OAc-extractable K and less clay and DTPA-extractable Fe. Chlorotic and green leaf blades contained about the same concentration of P, S, Mg, Fe, Zn, Cu, and Mo, but the former leaf blades had more K and less Ca and HCl soluble Fe than the green ones. Green leaves of plants that seemed to have naturally recovered in chlorotic fields were higher in Mn. A foliage spray with 2.5% FeSO₄.7H₂O solution resulted in greening of leaves and a field experiment showed marked crop response to Fe and some response to Mn. The results thus suggest that the chlorosis is due to a lime-induced Fe-deficiency with the possibility of some role of Mn in Fe nutrition in calcareous soil conditions.Deceased 22 September 1988     

Low frequency ac conduction and dielectric relaxation behavior of solution grown and uniaxially stretched poly(vinylidene fluoride) films

The measurements of ac conductivity [σ_m(ω)], dielectric constant [?′(ω)] and loss [?″(ω)] have been performed on solution grown (thickness ∼85 μm) and uniaxially stretched (thickness ∼25, 45 and 80 μm) films of poly(vinylidene fluoride) (PVDF) in the frequency range 0.1 kHz-10 MHz and in the temperature range 77-400 K. The σ_m(ω) can be described by the relation σ(ω) = Aω^s, where s is close to unity and decreases with increase in temperature. Three relaxations, observed in the present investigation, have been designated as the α_c-, the α_a- and the β-relaxations appearing from high temperature side to the low temperature side. The α_c-relaxation could not be observed in the case of uniaxially stretched poly(vinylidene fluoride) films. The α_c- and α_a-relaxations are associated with the molecular motions in the crystalline regions and micro-Brownian motion in the amorphous regions of the main polymer chain, respectively, whereas the β-relaxation is attributed to the rotation of side group dipoles or to the local oscillations of the frozen main polymer chain.     

Infrared study of salt free and salt treated cellulose pyrolysis under nitrogen atmosphere

The pyrolysis under nitrogen of salt free and salt treated cellulose was studied by infrared spectroscopy. The results confirm the unzipping mechanism suggested by DTA and TGA studies, and show this mechanism to apply to the untreated and salt treated samples. The results also show the unzipping to stop at the stage of char formation. The onset of this stage was found to occur after the volatilization of only 45–50% of the initial sample of the borax treated cellulose, compared with 65–70% of the KCl treated cellulose and 80–85% of the untreated cellulose.     

Target following with motion prediction for unmanned surface vehicle operating in cluttered environments

The capability of following a moving target in an environment with obstacles is required as a basic and necessary function for realizing an autonomous unmanned surface vehicle (USV). Many target following scenarios involve a follower and target vehicles that may have different maneuvering capabilities. Moreover, the follower vehicle may not have prior information about the intended motion of the target boat. This paper presents a trajectory planning and tracking approach for following a differentially constrained target vehicle operating in an obstacle field. The developed approach includes a novel algorithm for computing a desired pose and surge speed in the vicinity of the target boat, jointly defined as a motion goal, and tightly integrates it with trajectory planning and tracking components of the entire system. The trajectory planner generates a dynamically feasible, collision-free trajectory to allow the USV to safely reach the computed motion goal. Trajectory planning needs to be sufficiently fast and yet produce dynamically feasible and short trajectories due to the moving target. This required speeding up the planning by searching for trajectories through a hybrid, pose-position state space using a multi-resolution control action set. The search in the velocity space is decoupled from the search for a trajectory in the pose space. Therefore, the underlying trajectory tracking controller computes desired surge speed for each segment of the trajectory and ensures that the USV maintains it. We have carried out simulation as well as experimental studies to demonstrate the effectiveness of the developed approach.