Solutions to a combined problem of excessive hydrogen sulfide in biogas and struvite scaling.

The Woodman Point Wastewater Treatment Plant (WWTP) in Western Australia has experienced two separate problems causing avoidable maintenance costs: the build-up of massive struvite (MgNH4PO4. 6H2O) scaling downstream of the anaerobic digester and the formation of hydrogen sulfide (H2S) levels in the digester gas to levels that compromised gas engine operation and caused high operating costs on the gas scrubber. As both problems hang together with a chemical imbalance in the anaerobic digester, we decided to investigate whether both problems could be (feasibly and economically) addressed by a common solution (such as dosing of iron solutions to precipitate both sulfide and phosphate), or by using separate approaches. Laboratory results showed that, the hydrogen sulfide emission in digesters could be effectively and economically controlled by the addition of iron dosing. Slightly higher than the theoretical value of 1.5 mol of FeCl3 was required to precipitate 1 mol of dissolved sulfide inside the digester. Due to the high concentration of PO4(3-) in the digested sludge liquor, significantly higher iron is required for struvite precipitation. Iron dosing did not appear an economic solution for struvite control via iron phosphate formation. By taking advantage of the natural tendency of struvite formation in the digester liquid, it is possible to reduce the risk of struvite precipitation in and around the sludge-dewatering centrifuge by increasing the pH to precipitate struvite out before passing through the centrifuge. However, as the Mg2+/PO4(3-) molar ratio in digested sludge was low, by increasing the pH alone (using NaOH) the precipitation of PO4(3-) was limited by the amount of cations (Ca2+ and Mg2+) available in the sludge. Although this would reduce struvite precipitation in the centrifuge, it could not significantly reduce PO4(3-) recycling back to the plant. For long-term operation, maximum PO4(3-) reduction should be the ultimate aim to minimise PO4(3-) accumulation in the plant. Magnesium hydroxide liquid (MHL) was found to be the most cost-effective chemical to achieve this goal. It enhanced struvite precipitation from both, digested sludge and centrate to the point where more than 95% PO4(3-) reduction in the digested sludge was achieved.     

Piezoelectrically actuated four-bar mechanism with two flexible links for micromechanical flying insect thorax

In this paper, a piezoelectrically actuated four-bar mechanism with two flexible links is proposed to be used in a micromechanical flying insect robot wing thorax for stroke amplification. PZT-5H- and PZN-PT-based unimorph actuators are utilized at the input link of the four-bar for a compact and lightweight thorax transmission mechanism. The kinematics and dynamics of the proposed wing structure with two parallel four-bar mechanisms are analyzed, optimal four-bar link size selection method is introduced, and quasistatic forces generated at the wing are computed for evaluating the feasibility of the design. Using laser micromachining and folding techniques, prototype four-bar structures are constructed. In the experiments, for a 10/spl times/1/spl times/0.12 mm/sup 3/ PZT-5H actuator-based four-bar mechanism, the stroke amplification of around 20 - 25 is held, and an attached polyester wing is resonated at 29 Hz with around 90/spl deg/ flapping motion. These results match closely with the predicted theoretical values.     

Multilayer power printed structures suitable for controlling EMI noises generated in power converters

Electromagnetic interference (EMI) noises generated in power converters are diffused on the surface of conductors. This means influences occur from radiated EMI noises emitted from power transmission lines as well as conducted EMI noises transmitted from them. EMI noises diffusing on the surface of conductors are generally difficult to control using conventional concentrated constant theory. Thus, a new approach based on distributed constant circuit theory is needed in order to control EMI noises. A power converter structure to control EMI noises using multilayer power printed circuit technology is studied in this paper. A structure which can control EMI noises should simultaneously satisfy two conditions, i.e., one to shut down and one to attenuate EMI noises. The structure satisfying these conditions is studied through simulations using the Transmission-Line Modeling Method. The simulations show that the diffusion of EMI noises is controlled by dividing the flow of currents produced by EMI noises into the horizontal and perpendicular directions. That is, the horizontal current flow is controlled inside using the differences in the resistance produced from differences between inner and outer diameter of power transmission lines and the perpendicular current flow can be controlled by properly designing the thickness of the dielectric layer sandwiched between P-and N-power transmission lines with the symmetrical structure. Moreover, it is confirmed by simulations and experiments that the attenuation of EMI noises is affected by the width of the power transmission lines. It is expected that the results obtained in this paper can provide important rules when designing power converters with EMI noise control functions which use the multilayer power printed circuit technology.     

An investigation of sugar extraction methods and the use of microwave power for date syrup processing: efficiency and color related considerations.

This study investigates the effect of extraction methods on the color of date syrup and the potential use of microwave power for syrup processing. Sugar solutions were extracted from dates by boiling, soaking and blending. Color and sugar content of the extracted solutions were measured, and the percentage of sugar extracted form the total fruit sugar determined. Boiling was found to be the most efficient method of extraction whereby 74% of total samples sugar was extracted. In contrast, only 54.2% of fruit sugar was extracted by blending and 42% by soaking. In addition, solutions extracted by soaking and blending had a foaming problem in the subsequent concentration process. The extraction method had no effect on the product final color. The extracted solution was concentrated using two heating methods: conventional and microwave heating at a 600 W capacity and a frequency of 2450 MHz applied at three power levels: 10, 7, and 6. In the heating process, 180 minutes were needed to achieve a 77% degrees Brix using convective heating, while it took 81, 138, and 166 minutes of microwave heating at power level 10, 7, and 6, respectively to achieve the same concentration. Water activity of the syrup was measured within a sugar content range of 50 to 80% degrees Brix and the sugar concentration at which the product is shelf stable was determined at 76%.     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Problems of Wastewater Treatment and Methods of Solving Them

The studies show that in the combined use of biological and chemisorption stages of treatment, a deeper degree of removal of industrial pollutants from wastewaters is attained. The chemisorption stage allows stabilizing the treatment process in different concentration-temperature drops and increasing the degree of removal of synthetic surfactants (SSF), petroleum products, and nitrogen compounds. The possibility of regulating the selectivity of the treatment process by varying the composition of the chemisorption material is demonstrated.     

Reactions Between Ingredients in Binary Silicate Glasses

It is demonstrated that the density of binary glasses upon variation of the molar content of the modifier in their compositions obeys a parabolic dependence, whose parameters can be used to estimate the extent and type of reactions between the components. The reaction parameters in glasses that are prone to liquation are lower by an order of magnitude and have the negative sign.     

X-Ray Study of the Effect of Heat on the Structural Parameters of Armos Fibres

In studying a series of fibre samples spun in steady-state conditions, the following was found: as a function of the conditions of processing Armos fibre, two structural modifications of the polymer can form; intensive crystallization of the modification corresponding to the 28.7° reflection begins in heat treatment above 220°C; above 320°C, intensive crystallization of the modification corresponding to the 14.25° reflection is observed; at 360°C, symbatic enhancement of the intensities of both reflections with a weak change in the other structural parameters of the fibre is observed.     

Development of a Continuous Segmented Flow Tubular Reactor and the “Scale‐out” Concept – In Search of Perfect Powders

The synthesis of powders with controlled shape and narrow particle size distributions is still a major challenge for many industries. A continuous Segmented Flow Tubular Reactor (SFTR) has been developed to overcome homogeneity and scale‐up problems encountered when using batch reactors. Supersaturation is created by mixing the co‐reactants in a micromixer inducing precipitation; the suspension is then segmented into identical micro‐volumes by a non‐miscible fluid and sent through a tube. These micro‐volumes are more homogeneous when compared to large batch reactors leading to narrower size distributions, better particle morphology, polymorph selectivity and stoichiometry. All these features have been demonstrated on single tube SFTR for different chemical systems. To increase productivity for commercial application the SFTR is being “scaled‐out” by multiplying the number of tubes running in parallel instead of scaling‐up by increasing their size. The versatility of the multi‐tube unit will allow changes in type of precipitate with a minimum of new investment as new chemistry can be researched, developed and optimised in a single tube SFTR and then transferred to the multi‐tube unit for powder production.     

Reliability investigation of 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel

The authors have investigated the reliability performance of G-band (183 GHz) monolithic microwave integrated circuit (MMIC) amplifiers fabricated using 0.07-/spl mu/m T-gate InGaAs-InAlAs-InP HEMTs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel on 3-in wafers. Life test was performed at two temperatures (T/sub 1/ = 200 /spl deg/C and T/sub 2/ = 215 /spl deg/C), and the amplifiers were stressed at V/sub ds/ of 1 V and I/sub ds/ of 250 mA/mm in a N/sub 2/ ambient. The activation energy is as high as 1.7 eV, achieving a projected median-time-to-failure (MTTF) /spl ap/ 2 /spl times/ 10/sup 6/ h at a junction temperature of 125 /spl deg/C. MTTF was determined by 2-temperature constant current stress using /spl Delta/G/sub mp/ = -20% as the failure criteria. The difference of reliability performance between 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel and 0.1-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with In/sub 0.6/Ga/sub 0.4/As channel is also discussed. The achieved high-reliability result demonstrates a robust 0.07-/spl mu/m pseudomorphic InGaAs-InAlAs-InP HEMT MMICs production technology for G-band applications.