Effect of type of processing on the microstructural features and mechanical properties of Al-Cu/SiC metal matrix composites

In this study, an aluminum based metallic matrix (Al-2wt.% Cu) was reinforced with SiC particulates using a conventional casting technique and a new disintegrated melt deposition technique. Microstructural characterization studies conducted on the samples taken from disintegrated melt deposition technique revealed a more uniform distribution of SiC particulates and good interfacial integrity between SiC particulates and metallic matrix when compared to the conventionally cast composite samples. Results of ambient temperature mechanical tests demonstrate an increase in 0.2% YS and ultimate tensile strength of samples taken from disintegrated melt deposition technique when compared with the unreinforced and conventionally cast composite samples. The results of microstructural characterization and mechanical testing were finally rationalized in terms of the nature of processing technique employed to reinforce Al-2wt.% Cu metallic matrix with SiC particulates.     

Linear crosstalk in 4×4 semiconductor optical amplifier gateswitch matrix

We report a comprehensive crosstalk investigation of a packaged InGaAsP/InP 4×4 semiconductor optical amplifier gate switch matrix, experimentally as well as theoretically. For a fully loaded switch with the same wavelength on all four inputs, all possible switching combinations are analyzed, thus yielding realistic crosstalk figures. Coherent and incoherent crosstalk phenomena are identified, and a switch crosstalk less than -40 dB has been measured     

Ultralow-voltage boron-doped diamond field emitter vacuum diode

A boron-doped diamond field emitter diode with ultralow turn-on voltage and high emission current is reported. The diamond field emitter diode structure with a built-in cap was fabricated using molds and electrostatic bonding techniques. The emission current versus anode voltage of the capped diamond emitter diode with boron doping, sp² content, and vacuum thermal electric (VTE) treatment shows a very low turn-on voltage of 2 V. A high emission current of 1 μA at an anode voltage of less than 10 V can be obtained from a single diamond tip. The turn-on voltage is significantly lower than comparable silicon field emitters     

Simplified 0.35-μm flash EEPROM process using high-temperatureoxide (HTO) deposited by LPCVD as interpoly dielectrics and peripheraltransistors gate oxide

A simplified flash EEPROM process was developed using high-temperature LPCVD oxide both as flash cells interpoly dielectrics and as peripheral transistors gate oxide (decoding logic). An O₂ anneal at 850°C lowers charge trapping and interface trap density induced by Fowler-Nordheim injection. However, electron trapping remains slightly higher than with dry thermal oxide. Similar memory charge loss and write-erase endurance are obtained as for ONO-insulated cells. HTO thus proves to have the required quality and reliability to be used in flash EEPROMs     

Parallel, self-organizing, hierarchical neural networks. II

For pt.I see IEEE Trans. Neural Networks, vol.1, p.167-78 (1990). Parallel, self-organizing, hierarchical neural networks (PSHNNs) involve a number of stages with error detection at the end of each stage, i.e., rejection of error-causing vectors, which are then fed into the next stage after a nonlinear transformation. The stages operate in parallel during testing. Statistical properties and the mechanisms of vector rejection of the PSHNN are discussed in comparison to the maximum likelihood method and the backpropagation network. The PSHNN is highly fault tolerant and robust against errors in the weight values due to the adjustment of the error detection bounds to compensate errors in the weight values. These properties are exploited to develop architectures for programmable implementations in which the programmable parts are reduced to on-off or bipolar switching operations for bulk computations and attenuators for pointwise operations     

On obtaining shape from color shading

Color and Grassmann-Cayley Coordinates of Shape are considered in this article. The image irradiance equation for colored surfaces and the Grassman manifold λ of orbits Q = {B · h + c; detB ≠ 0} Where c is a vector sweeping the color space H, B is a 3 × 3 matrix, and h(x, y) is the color image of a Lambertian surface assumed to be a linear vector-function of the normal vectors. Different orbits Q(n) correspond to different shapes but they are invariant under color and illuminant transformation. Coordinates of an orbit Q in λ can be computed as 3 × 3 (2 × 2, sometimes) determining the elements of which are values of some linear functionals (receptive fields) of h(x, y). Based on the approach, a shape-from-shading algorithm was developed and successfully tested on the threeband color images of various real objects (an egg, cylinders and cones made of paper, etc.). © 1993 John Wiley & Sons, Inc.     

Optimum design for buckling of plain and stiffened composite axisymmetric shell panels/shells

The buckling of plain and discretely stiffened composite axisymmetric shell panels/shells made of repeated sublaminate construction is studied using the finite element method. In repeated sublaminate construction, a full laminate is obtained by repeating a basic sublaminate, which has a smaller number of plies. The optimum design for buckling is obtained by determining the layup sequence of the plies in the sublaminate by ranking, so as to achieve maximum buckling load for a specified thickness. For this purpose, a four-noded 48-dof quadrilateral composite thin shell element, together with fully compatible two-noded 16-dof composite meridional and parallel circle stiffener elements are used.