Screening of lactic acid bacteria for fermentation of minced wastes of Argentinean hake (Merluccius hubbsi)

Sixteen strains of lactic acid bacteria were evaluated for their capacity of acidification of Merluccius hubbsi fish wastes obtained from a processing factory. Only three lactobacilli (Lactobacillus buchneri B-1837, Lactobacillus arizonensis B-14768 and Lactobacillus plantarum B-4496) were able to reduce the pH value to 4.0 or below when using glucose or sucrose as carbon source. Either with only 25 g l^?1 of glucose or sucrose, L. arizonensis B-14768 reduced the pH to 3.8 ± 0.2 within 24 h of fermentation. The acid tolerance test (pH 3.0 at 37 °C) for the strains presented D_pH3-values of 192, 383 and 767 min for L. buchneri, L. plantarum and L. arizonensis, respectively. However, at a lower pH value (pH 2.0) only L. arizonensis was significantly recovered after 45 min of exposure (D_pH2 68 min). Considering together the acidification capacity, the tolerance to other stresses (heat and bile salts) and the lower optimum temperature for the process, L. arizonensis is described as a suitable strain for M. hubbsi silage; constituting a promissory alternative for fish fermentation at location with temperate or cold climes.     

The effect of different porous media on moisture loss and oil absorption profiles during frying using glass micromodels

Microstructure plays a key role in oil absorption during frying. The aim of this work was to improve our understanding of the relationship between microstructure and oil absorption, through the use of glass micromodels to obtain evidence of transport phenomena in three porous networks. Micromodels were saturated with water and partially immersed in oil at 190°C. Moisture and oil profiles were imaged to get water and oil saturation maps. Image and fractal analyses were performed to describe the morphology of the evaporation and oil fronts. Results showed that higher porosity facilitated the moisture removal and promoted greater oil absorption during cooling. The fractal dimension showed that microstructures with a relatively high number of fine capillaries were less stable and propitiated fingering during the advance of the evaporation front. In all matrices, the disruption of the surface oil film due to air penetration was a critical factor to stop oil imbibition. © 2015 American Institute of Chemical Engineers AIChE J, 62: 629–638, 2016     

Organochlorine Formation in Tertiary Amine Catalyzed Pulp Bleaching

An oxygen delignified eucalyptus kraft pulp was bleached by applying a catalytic amount of a tertiary amine, 1,4-diazabicyclo[2,2,2]octane, and hypochlorous acid at varying pH, temperature, and time. The bleaching filtrate was analyzed for chloroform and AOX and the pulp for residual lignin, hexenuronic acid, and OX. In comparison with chlorine dioxide bleaching, the novel catalytic bleaching (pH < 6) generated only traces of chloroform and low contents of AOX and OX. Separate catalytic oxidations of authentic hexenuronic acid showed that it was a major precursor of chloroform. The results demonstrate a practical way to reduce organochlorine formation in pulp bleaching and provide new understanding on the reaction pathways that yield chloroform.     

Composites made from a soybean oil biopolyurethane and cellulose nanocrystals

Cellulose nanocrystals (CNC) obtained by acidic hydrolysis from microcrystalline cellulose were dispersed in a biopolyurethane matrix to prepare composite films. The polyurethane was prepared from a hydroxylated soybean oil (SO‐OH) and a polymeric diphenyldiisocyanate (pMDI), using a organotin compound as the catalyst. The composite films contained different concentrations of nanocelullose, without any macroscopic aggregates in all cases. Thermal, tensile and dynamic mechanical properties of the films were determined for all the samples. In particular, it was observed that the glass transition temperature of the nanocomposites slightly increased with the concentration of the cellulose nanocrystals. The nanocomposite with 1 wt% of nanocellulose showed the highest tensile strength of the series. POLYM. ENG. SCI., 58:125–132, 2018. © 2017 Society of Plastics Engineers     

Optimization of properties in a rubber compound containing a ternary polymer blend using response surface methodology

In order to find the best combination of three synthetic rubbers, that is, styrene‐butadiene rubber (SBR) grade 1712, SBR grade 1721 and high‐1,4‐cis polybutadiene, that produce a compound with specific end‐use properties, a statistical experimental design is proposed in this work. The design consists of ten mixtures containing specific amounts of total styrene and BR content. A number of properties are tested in each mixture, selecting those related to requirements for the tread of a high performance tire: glass transition temperature (T_g), the ratio between the viscous modulus and the elastic modulus (tanδ@60 °C), Mooney viscosity, and the tensile properties. The values obtained for each property are fit to statistically significant models, obtaining the respective response surfaces. These are next used to define a desirable formulation with the optimal ratio of each rubber, and finally the optimized formulation is validated by comparing the experimental and predicted values for each modeled property. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46548.     

Removal of sulfamethoxazole from waters and wastewaters by conductive‐diamond electrochemical oxidation

BACKGROUND: Sulfamethoxazole (SMX, used as a model bacteriostatic antibiotic) is persistent to conventional biological treatments of wastewaters. In this work, conductive‐diamond electrochemical oxidation (CDEO) was found to be an effective technology for its removal from the effluents of conventional wastewater treatment plants. RESULTS: The use of CDEO has been evaluated for the removal of the antibiotic SMX from water and wastewaters. The results show that CDEO can reduce the concentration of this organic pollutant to values below 0.1 µg dm^?3. The variation of the SMX concentration during electrolysis shows a complex shape with a plateau zone that increases in size with the initial concentration of SMX. This complex trend is not observed in the changes of TOC, which seems to indicate that the CDEO of SMX solutions does not lead directly to the generation of carbon dioxide as a final product. A tentative reaction pathway has been proposed based on a thorough analysis of the reaction mixture, in which the main intermediate products were identified. The use of liquid chromatography time‐of‐flight mass spectrometry (LC‐TOFMS) allowed the identification of nine organic intermediates (with M_w 98, 108, 172, 173, 197, 203, 227, 269 and 287) during the electrolysis and the concentration of these compounds depends on the initial SMX concentration and on the current density applied. CONCLUSIONS: CDEO is able to reduce the concentration of the organic pollutant below 0.1 mg dm^?3. SMX removal is faster than that of TOC. This fact indicates the formation of reaction intermediates. Analytical techniques show that nine reaction intermediates are generated in the system, and that their concentration depends on the initial SMX concentration and on the current density used. Copyright © 2012 Society of Chemical Industry