Flexural strength evaluations and fractography analyses of slip cast mesoporous submicron alumina

Mesoporous submicron α?Al₂O₃ green compacts were fabricated using slip casting of ultrafine alumina powders. The pre-sintered samples were sintered in air atmosphere at 1300 °C, 1350 °C, 1400 °C, and 1500 °C to obtain a variety of grain morphologies namely submicron equiaxed and micro rod structures. The resulting grain diameters lie between ～ 270 nm and ～ 1590 nm and total porosity fraction between 0.05% and 13%. The room temperature flexural strength (σ) evaluations and fractography analyses of sintered alumina samples were performed. It was observed that the total porosity fraction dictates the flexural strength as compared to grain diameter. Further, it was found that the flexural strength exhibited a decreasing trend for an increase in the total porosity fraction, and proved to be a better effective parameter than open porosity fraction. The fractography analyses suggest that samples sintered at 1300 °C and 1350 °C predominantly underwent intergranular fracture, while those sintered at 1400 °C and 1500 °C underwent a mixture of intergranular and transgranular fracture.     

Mechanical properties of illite-based ceramics with controlled porosity studied by modern in situ techniques

Deformation tests combined with modern in situ acoustic emission (AE) and digital image correlation (DIC) techniques were applied to monitor low strain rate compressive behavior of illite-based ceramics with controlled porosity (P). A strong effect of porosity on the mechanical performance was observed: Young's modulus decreased linearly from 29.4 ± 1.1 GPa (P = 14 vol%) to 3.0 ± 0.5 GPa (P = 55 vol%) and compressive strength decreased from 307 ± 13.6 MPa (P = 14 vol%) to 27.7 ± 1.0 MPa (P = 55 vol%). The AE and DIC techniques revealed a transition from brittle fracture to gradual localized crushing with increasing porosity. The AE signals possessed high-energy burst-like characteristics typical of brittle fracture and (micro)cracking. The AE data showed continuous activity from the beginning of loading, suggesting that true elasticity does not occur in this material. The combination of mechanical tests with in situ techniques, therefore, proved to be particularly effective in providing additional information on the deformation dynamics in ceramics.     

Data-driven deep density estimation

Neural Computing and Applications - Density estimation plays a crucial role in many data analysis tasks, as it infers a continuous probability density function (PDF) from discrete samples. Thus, it...     

On the Controlled Loading of Single Platinum Atoms as a Co-Catalyst on TiO2 Anatase for Optimized Photocatalytic H2 Generation

Single-atom (SA) catalysis is a novel frontline in the catalysis field due to the often drastically enhanced specific activity and selectivity of many catalytic reactions. Here, an atomic-scale defect engineering approach to form and control traps for platinum SA sites as co-catalyst for photocatalytic H₂ generation is described. Thin sputtered TiO₂ layers are used as a model photocatalyst, and compared to the more frequently used (001) anatase sheets. To form stable SA platinum, the TiO₂ layers are reduced in Ar/H₂ under different conditions (leading to different but defined Ti³⁺-O_v surface defects), followed by immersion in a dilute hexachloroplatinic acid solution. HAADF-STEM results show that only on the thin-film substrate can the density of SA sites be successfully controlled by the degree of reduction by annealing. An optimized SA-Pt decoration can enhance the normalized photocatalytic activity of a TiO₂ sputtered sample by 150 times in comparison to a conventional platinum-nanoparticle-decorated TiO₂ surface. HAADF-STEM, XPS, and EPR investigation jointly confirm the atomic nature of the decorated Pt on TiO₂. Importantly, the density of the relevant surface exposed defect centers—thus the density of Pt-SA sites, which play the key role in photocatalytic activity—can be precisely optimized.     

Highly Customizable Bone Fracture Fixation through the Marriage of Composites and Screws

Open reduction internal fixation (ORIF) metal plates provide exceptional support for unstable bone fractures; however, they often result in debilitating soft-tissue adhesions and their rigid shape cannot be easily customized by surgeons. In this work, a surgically feasible ORIF methodology, called AdhFix, is developed by combining screws with polymer/hydroxyapatite composites, which are applied and shaped in situ before being rapidly cured on demand via high-energy visible-light-induced thiol–ene coupling chemistry. The method is developed on porcine metacarpals with transverse and multifragmented fractures, resulting in strong and stable fixations with a bending rigidity of 0.28 (0.03) N m² and a maximum load before break of 220 (15) N. Evaluations on human cadaver hands with proximal phalanx fractures show that AdhFix withstands the forces from finger flexing exercises, while short- and long-term in vivo rat femur fracture models show that AdhFix successfully supports bone healing without degradation, adverse effects, or soft-tissue adhesions. This procedure represents a radical new approach to fracture fixation, which grants surgeons unparalleled customizability and does not result in soft-tissue adhesions.     

Confined adamantane molecules assembled to one dimension in carbon nanotubes

We have encapsulated adamantane (C₁₀H₁₆) in single- and multi-walled carbon nanotubes. Adamantane is a high symmetry cage like molecule with point group symmetry T_d and can be considered as a hydrogen-terminated diamond fragment. We confirmed and identified the successful filling by high resolution transmission electron microscopy, ¹³C nuclear magnetic resonance, infrared and Raman spectroscopy. ¹³C nuclear magnetic resonance of the adamantane filled nanotubes reveals that the adamantane molecules stop rotating after encapsulation. A blue-shift of the Raman active radial breathing modes of the carbon nanotubes supports this and suggests a significant interaction between encapsulated adamantane molecules and the single wall nanotubes. The encapsulated adamantane molecules exhibit red shifted infrared C–H vibration modes which we assign to a slight elongation of the C–H bonds. We observe both a nanotube diameter dependence of the adamantane filling ratio and a release rate of adamantane from the CNTs that depends on the CNT diameters.     

Population changes in a biofilm reactor for phosphorus removal as evidenced by the use of FISH

Induction of denitrification was investigated for a lab-scale phosphate removing biofilm reactor where oxygen was replaced with nitrate as the electron acceptor. Acetate was used as the carbon source. The original biofilm (acclimatised with oxygen) was taken from a well-established large-scale reactor. During the first run, a decrease in the denitrifying bio-P activity was observed after 1 month following a change in the anaerobic phase length. This was initially interpreted as a shift in the microbial population caused by the changed operation. In the second run, biomass samples were regularly collected and analysed by fluorescent in situ hybridisation (FISH) and confocal laser scanning microscopy (CLSM). Concurrently, samples were taken from the original reactor with oxygen as electron acceptor in order to investigate natural microbial fluctuations. A similar decrease in the activity as in the first run was seen after one month, although the phase lengths had not been varied. Hence, the decrease after 1 month in the first and second run should be seen as a start-up phenomenon. FISH could detect a noticeable shift in the microbial population mainly within the first 2 weeks of operation. Almost all bacteria belonging to the alpha subclass disappeared and characteristic clusters of the beta and gamma subclasses were lost. Small clusters of gram-positive bacteria with a high DNA G + C content (GPBHGC) were gradually replaced by filamentous GPBHGC. Most of the bacteria in the denitrifying, phosphate removing biofilm belonged to the beta subclass of Proteobacteria. The applied set of gene probes had been selected based on existing literature on biological phosphate removing organisms and included a recently published probe for a Rhodocyclus-like clone. However, none of the specific probes hybridised to the dominant bacterial groups in the reactors investigated. No noticeable changes were detected in the aerobic bench-scale reactor during this period, indicating that the observed changes in the lab-scale reactor were caused by the changed environment.     

Screening of human antibiotic substances and determination of weekly mass flows in five sewage treatment plants in Sweden

Twelve antibiotic substances for human use, including trimethoprim and representatives of the fluoroquinolone (FQ), sulfonamide (SA), penicillin (PE), cephalosporin (CE), nitroimidazole (NI), tetracycline (TC), and macrolide (MA) groups, were subjected to a screening study at five Swedish sewage treatment plants (STPs) during one week in 2002 and one week in 2003. The analytes were extracted from raw sewage water, final effluent, and sludge by solid-phase extraction (SPE) or liquid-solid extraction (as appropriate) and then identified and quantified by liquid chromatography/tandem mass spectrometry. The mostfrequently detected antibiotics in the matrices considered in this study were norfloxacin, ofloxacin, ciprofloxacin, trimethoprim, sulfamethoxazole, and doxycycline. The other analytes were only detected in a few samples. Analysis of the weekly mass flows through each STP showed that FQs were partly eliminated from the water during sewage water treatment and the highest amounts of these substances were found in sludge. Sulfamethoxazole and trimethoprim were mainly found in raw sewage water and final effluent, but these substances had balancing mass flows, indicating that they too can withstand sewage water treatment. The mass flow patterns for doxycycline were more complex, with high amounts occurring in sludge in some cases, suggesting thatthe behavior of this analyte may be more strongly influenced by the treatment process and other variables at individual STPs. The environmental load (the sum of the amounts in the final effluent and sludge) normalized to the number of inhabitants in the catchment area of each investigated STP compared with theoretical predictions based on consumption data (in parentheses) showed good correlations: norfloxacin, 0.8 (0.9); ofloxacin, 0.3 (0.2); ciprofloxacin, 1.3 (3.5); sulfamethoxazole, 0.2 (0.4); trimethoprim, 1.1 (1.0); and doxycycline, 0.7 (0.4) mg per person per week. The results show that reasonably accurate predictions of environmental load of these antibiotics can be time-effectively derived from consumption data without additional measurements.     

Synthesis,Molecular Docking and Biological Characterization of Pyrazine Linked 2-Aminobenzamides as New Class I Selective Histone Deacetylase (HDAC) Inhibitors with Anti-Leukemic Activity

Class I histone deacetylases (HDACs) are key regulators of cell proliferation and they are frequently dysregulated in cancer cells. We report here the synthesis of a novel series of class-I selective HDAC inhibitors (HDACi) containing a 2-aminobenzamide moiety as a zinc-binding group connected with a central (piperazin-1-yl)pyrazine or (piperazin-1-yl)pyrimidine moiety. Some of the compounds were additionally substituted with an aromatic capping group. Compounds were tested in vitro against human HDAC1, 2, 3, and 8 enzymes and compared to reference class I HDACi (Entinostat (MS-275), Mocetinostat, CI994 and RGFP-966). The most promising compounds were found to be highly selective against HDAC1, 2 and 3 over the remaining HDAC subtypes from other classes. Molecular docking studies and MD simulations were performed to rationalize the in vitro data and to deduce a complete structure activity relationship (SAR) analysis of this novel series of class-I HDACi. The most potent compounds, including 19f, which blocks HDAC1, HDAC2, and HDAC3, as well as the selective HDAC1/HDAC2 inhibitors 21a and 29b, were selected for further cellular testing against human acute myeloid leukemia (AML) and erythroleukemic cancer (HEL) cells, taking into consideration their low toxicity against human embryonic HEK293 cells. We found that 19f is superior to the clinically tested class-I HDACi Entinostat (MS-275). Thus, 19f is a new and specific HDACi with the potential to eliminate blood cancer cells of various origins.