双层有机电致发光器件有机层厚度优化的数值研究

在陷阱电荷限制电流传导理论的基础上,提出了双层有机电致发光器件的数值模型,研究了结构为"阳极/空穴输运层(HTL)/发光层(EML)/阴极"的器件中电流密度和量子效率随有机层的特征陷阱能量、陷阱密度和载流子迁移率的依赖关系. 研究发现,对于给定的HTL和EML的特征陷阱能量、陷阱密度和载流子迁移率,存在一个最优的HTL和EML之间的厚度比率,在此最优厚度比下,器件的电流密度和量子效率达到最大.通过有机层厚度的优化,器件的电流密度和量子效率可提高多达两个数量级.另外,还研究了最优厚度比随有机层特征陷阱能量、总陷阱密度和载流子迁移率之间的定量关系.     

Improving narrow bandgap a-SiGe:H alloys grown by hot-wire chemical vapor deposition

We have improved the electronic properties of narrow-bandgap (Tauc gap below 1.5 eV) amorphous-silicon germanium alloys (a-SiGe:H) grown by hot-wire chemical vapor deposition (HWCVD) by lowering the substrate temperature and deposition rate. Prior to this work, we were unable to grow a-SiGe:H alloys with bandgaps below 1.5 eV that had photo-to-dark conductivity ratios comparable with our plasma-enhanced CVD (PECVD) grown materials [B.P. Nelson et al., Mater. Res. Soc. Symp. 507 (1998) 447]. Decreasing the filament diameter from our standard configuration of 0.5 mm to 0.38 or 0.25 mm provides first big improvements in the photoresponse of these alloys. Lowering the substrate temperature from our previous optimal temperatures (T_sub starting at 435 °C) to at 250 °C provides additional photo-to-dark conductivity ratio increasing by two orders of magnitude for growth conditions containing 20–30% GeH₄ in the gas phase (relative to the total GeH₄+SiH₄ flow).     

用CMOS工艺实现非接触IC卡天线的集成化设计

论述了用CMOS工艺实现非接触式IC卡天线的集成化需要考虑的各个方面,建立了集成天线的模型,给出了合理的设计方案,并通过实验验证了模型和设计方案.实验结果表明,采用片上天线完全可以提供非接触式IC卡工作所需要的能量.在频率为2 2 .5 MHz、感应强度为6×10 - 4 T的磁场中,面积为2 m m×2 mm的集成天线可以为10 kΩ的负载提供1.2 2 5 m W的能量.     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

AutoCAD的应用技巧

随着我国经济的高速发展,业主要求提交资料的时间越来越短。为了提高工作效率,保质保量地完成工作,本文介绍了一些AutoCAD 2000及其以上版本的比较实用的技巧。灵活掌握了以下技巧后,绘图速度大约能提高50%。     

Layered Wyner-Ziv video coding.

Following recent theoretical works on successive Wyner-Ziv coding (WZC), we propose a practical layered Wyner-Ziv video coder using the DCT, nested scalar quantization, and irregular LDPC code based Slepian-Wolf coding (or lossless source coding with side information at the decoder). Our main novelty is to use the base layer of a standard scalable video coder (e.g., MPEG-4/H.26L FGS or H.263+) as the decoder side information and perform layered WZC for quality enhancement. Similar to FGS coding, there is no performance difference between layered and monolithic WZC when the enhancement bitstream is generated in our proposed coder. Using an H.26L coded version as the base layer, experiments indicate that WZC gives slightly worse performance than FGS coding when the channel (for both the base and enhancement layers) is noiseless. However, when the channel is noisy, extensive simulations of video transmission over wireless networks conforming to the CDMA2000 1X standard show that H.26L base layer coding plus Wyner-Ziv enhancement layer coding are more robust against channel errors than H.26L FGS coding. These results demonstrate that layered Wyner-Ziv video coding is a promising new technique for video streaming over wireless networks.     

应用时频分析方法辨识时变系统的模态参数

应用Gabor展开及Hilbert变换进行时变线性系统模态参数的辨识。利用非平稳信号的Gabor变换将结构响应信号表示在时频面上，并通过Gabor展开重构分离模态分量，建立每一阶模态的时变线性模型。对单模态时变线性模型应用Hilbert变换来辨识随时间变化的模态频率和阻尼。通过对刚度和阻尼慢变的两自由度系统模态参数的仿真辨识验证辨识方法的有效性。仿真结果表明：本文方法为时变线性系统的模态参数辨识提供了一条新的途径。     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi     

MULTICARRIER DS—CDMA WITH ADAPTIVE MODULATION AND POWER ALLOCATION

Adaptive modulation and power allocation is introduced into the multicarrier DSCDMA system to improve the system performance and bandwidth efficiency.First,the system design appropriate for adaptive modulation and power allocation is given,then the algorithm of adaptive modulation and power allocation is applied.Simulation results demonstrate great performance improvement compared with the fixed modulated one.