Estimating thermal stress in BIPV modules

The thermal stress on building‐integrated photovoltaic modules (BIPV) in Espoo, Finland, was studied with field‐testing of amorphous silicon modules. Based on these results, the thermal stress at two other European locations (Paris and Lisbon) was estimated. The estimation procedure entailed thermal modelling of heat transfer in the façade with meteorological data as input. The results indicate that the thermal stress on BIPV modules in Lisbon is, in this case, approximately 50% higher that in Espoo and between 80 and 200% higher than in Paris, depending on the activation energy of the degradation process. The difference in stress between a BIPV module and a free‐standing module in Espoo was 50–200%. Copyright © 2006 John Wiley & Sons, Ltd.     

Buchbesprechungen

Ohne Zusammenfassung     

Expert identification and selection: Legal liability concerns and directions

Legal liabilities pertaining to the identification and selection of domain experts is an issue that could adversely impact expert systems developers. Problems pertaining to flawed knowledge, improperly defined expertise, and behavioural and psychological impediments are just some of the issues. This paper examines the torts of strict products liability and negligence that system developers could incur as a result of expert-related difficulties. Parallels from legal scholars and federal and state court decisions are discussed relevant to expert system projects and developers. The paper concludes with a presentation of steps that systems developers can take to minimize potential legal liability.     

Optical and electrical characterization of CdS thin films

Thin CdS films have been grown by chemical bath (CdCl₂, thiourea, ammonia) deposition (CBD) on SnO₂ (TO)-coated glass substrate for use as window materials in CdS/CdTe solar cells. High-resolution transmission electron microscopy revealed grains with an average size of 10 nm. The structure was predominantly hexagonal with a high density of stacking faults. The film crystallinity improved with annealing in air. Annealing in a CdCl₂ flux increased the grain size considerably and reduced the density of stacking faults. The optical transmission of the as-deposited films indicated a band gap energy of 2.41 eV. Annealing in air reduced the band gap by 0.1 eV. Annealing in CdCl₂ led to a sharper optical absorption edge that remained at 2.41 eV. Similar band gap values were obtained by photocurrent spectroscopy and electroabsorption spectroscopy (EEA) using an electrolyte contact. EEA spectra were broad for the as-deposited and air-annealed samples, but narrower for the CdCl₂-annealed films, reflecting the reduction in stacking fault density. Donor densities of ca. 10¹⁷ cm ^–3 were derived from the film/electrolyte junction capacitance.     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

Augmented platelet aggregation as predictor of reocclusion after thrombolysis in acute myocardial infarction

RATIONALE: Reocclusion after thrombolysis diminishes the benefits of early reperfusion after acute myocardial infarction (AMI). No clinical or laboratory variables have been identified as predictors for reocclusion yet. METHODS AND RESULTS: To evaluate hemostatic variables as potential risk determinants platelet aggregation (PA, representing platelet activity), thrombin/antithrombin complexes (TAT, representing thrombin generation), and plasminogen activator inhibitor type 1 (PAI-1, representing endogenous fibrinolysis) were determined in 31 patients with AMI at 0, 1, 2. and 12 h after the start of thrombolysis as well as at hospital discharge. Reocclusion (defined as reinfarction or angiographically confirmed, clinically silent coronary reocclusion) occurred in 5 patients within 5-14 days and in 8 patients within 1 year. TAT plasma concentrations were lower in patients with reocclusion than in those without (9.9+/-5.7 vs. 22.9+/-22.2 ng/ml at 2 h, 6.5+/-3.1 vs. 1 1.2+/-6.4 ng/ml at 12 h, means+/-SD, p <0.05 each). Neither concentration nor activity of PAI-1 in plasma differed between both patient groups. However, both slope and maximum of PA (induced by 2 micromol/l ADP) were augmented in patients with reocclusion (slope: 39.4+/-1.7 vs. 32.5+/-7.4 at 2 h, p <0.001; 42.6+/-2.6 vs. 36.6+/-8.9 at 12 h, p <0.01). Results were independent of the thrombolytic agent used (alteplase or reteplase). A PA slope at 2 h higher than the average slope before thrombolysis (37.2+/-5.7) could be identified as best predictor for early (within 5-14 d, p=0.017, sensitivity 1.00, specificity 0.69) and late reocclusion (within 1 y, p=0.009, 0.88 and 0.74, respectively). CONCLUSIONS: Increased PA following coronary thrombolysis appears to be associated with early and late reocclusion. This marker could be useful in identifying patients who may benefit from more aggressive antiplatelet (such as GP IIb/IIIa receptor antagonists), interventional, or both strategies.     

Aeromagnetic compensation using neural networks

Airborne magnetic surveys in geophysical exploration can be subject to interference effects from the aircraft. Principal sources are the permanent magnetism of various parts of the aircraft, induction effects created by the earth's magnetic field and eddy-current fields produced by the aircraft's manoeuvres. Neural networks can model these effects as functions of roll, pitch, heading and their time derivatives, together with vertical acceleration, charging currents to the generator, etc., without assuming an explicit physical model. Separation of interference effects from background regional and diurnal fields can also be achieved in a satisfactory way.