Computation of the average power pattern of a reflector antennawith random surface errors and misalignment errors

To specify manufacturing tolerances of a reflector antenna, various errors such as random surface errors and misalignment errors must be considered at one time because superposition of the effects of those errors may not hold. Based on the Rahmat-Samii's formulation (1983), a method for computing efficiently the average power pattern of a reflector antenna with those errors is presented. Simulation results show that superposition of the effects of errors does not generally hold and demonstrate how those errors degrade the peak-gain and sidelobe levels     

Enhancement mode InP MISFET's with sulfide passivation andphoto-CVD grown P3N5 gate insulators

High performance enhancement mode InP MISFET's have been successfully fabricated by using the sulfide passivation for lower interface states and with photo-CVD grown P₃N₅ film used as gate insulator. The MISFET's thus fabricated exhibited exhibited pinch-off behavior with essentially no hysteresis. Furthermore the device showed a superior stability of drain current. Specifically under the gate bias of 2 V for 10⁴ seconds the room temperature drain current was shown to reduce from the initial value merely by 2.9% at the drain voltage of 4 V. The effective electron mobility and extrinsic transconductance are found to be about 2300 cm ²/V·s and 2.7 mS/mm, respectively. The capacitance-voltage characteristics of the sulfide passivated InP MIS diodes show little hysteresis and the minimum density of interface trap states as low as 2.6×10¹⁴/cm² eV has been attained     

An efficient assumed strain element model with six DOF per node for geometrically non-linear shells

The present paper describes an assumed strain finite element model with six degrees of freedom per node designed for geometrically non-linear shell analysis. An important feature of the present paper is the discussion on the spurious kinematic modes and the assumed strain field in the geometrically non-linear setting. The kinematics of deformation is described by using vector components in contrast to the conventional formulation which requires the use of trigonometric functions of rotational angles. Accordingly, converged solutions can be obtained for load or displacement increments that are much larger than possible with the conventional formulation with rotational angles. In addition, a detailed study of the spurious kinematic modes and the choice of assumed strain field reveals that the same assumed strain field can be used for both geometrically linear and non-linear cases to alleviate element locking while maintaining kinematic stability. It is strongly recommended that the element models, described in the present paper, be used instead of the conventional shell element models that employ rotational angles.     

The design of robots and intelligent manipulators using modern composite materials

The operating speed and endpoint positional accuracy of existing industrial manipulators are limited by the inertial and stiffness characteristics of the articulating members of the robot's mechanical linkage. This limitation may be overcome by developing members having high structural stiffness and strength with low mass, and this has been recognized for some time. These characteristics can be obtained by fabricating the moving members of manipulators in fiber reinforced composite materials. In order to establish a basis for the dynamic analysis of robots fabricated in viscoelastic composites, a variational theorem is developed herein. A preliminary comparative study is then undertaken for manipulators manufactured in a graphite-epoxy composite material and also steel in order to demonstrate some of the advantages to be accrued from this proposed new design philosophy.     

Application of differential quadrature to static analysis of structural components

The numerical technique of differential quadrature for the solution of linear and non-linear partial differential equations, first introduced by Bellman and his associates, is applied to the equations governing the deflection and buckling behaviour of one- and two-dimensional structural components. Separate transformations are used for higher-order derivatives, as suggested by Mingle, thus extending the method to treat fourth-order equations and to include multiple, boundary conditions in the respective co-ordinate directions. Results are obtained for various boundary and loading conditions and are compared with existing exact and numerical solutions by other methods. The application of differential quadrature to this class of problems is seen to lead to accurate results with relatively small computational effort.     

Pressure effects on flow and fracture of Be-Al alloys

The flow and fracture behavior of Be-Al alloys were determined in tension with different levels of superimposed pressure. The Be-Al alloys were prepared by Brush Wellman, Inc. (Cleveland, OH) from prealloyed powders processed to either a hot isostatically pressed (“hipped”) or cold isostatically pressed and extruded condition. Significant effects of pressure on both the flow and ductility have been observed at room temperature, with implications on the formability of these materials. The effects of changes in processing conditions and stress state on the flow and fracture behavior are summarized in addition to both optical and scanning electron microscopy (SEM) examination of the fracture surfaces. Separate other studies on the alloy constituents (e.g., Al and Be) are also reported. The results are also compared to previous works on monolithic materials and composites tested with high pressure.     

Spatial learning deficits in mice with a targeted glucocorticoid receptor gene disruption

Previous studies in rats using the Morris water maze suggested that the processing of spatial information is modulated by corticosteroid hormones through mineralocorticoid and glucocorticoid receptors in the hippocampus. Mineralocorticoid receptors appear to be involved in the modulation of explorative behaviour, while additional activation of glucocorticoid receptors facilitates the storage of information. In the present study we used the water maze task to examine spatial learning and memory in mice homozygous and heterozygous for a targeted disruption of the glucocorticoid receptor gene. Compared with wild-type controls, homozygous and heterozygous mice were impaired in the processing of spatial but not visual information. Homozygous mutants performed variably during training, without specific platform-directed search strategies. The spatial learning disability was partly compensated for by increased motor activity. The deficits were indicative of a dysfunction of glucocorticoid receptors as well as of mineralocorticoid receptors. Although the heterozygous mice performed similarly to wild-type mice with respect to latency to find the platform, their strategy was more similar to that of the homozygous mice. Glucocorticoid receptor-related long-term spatial memory was impaired. The increased behavioural reactivity of the heterozygous mice in the open field points to a more prominent mineralocorticoid receptor-mediated function. The findings indicate that (i) the glucocorticoid receptor is of critical importance for the control of spatial behavioural functions, and (ii) mineralocorticoid receptor-mediated effects on this behaviour require interaction with functional glucocorticoid receptors. Until the development of site-specific, inducible glucocorticoid receptor mutants, glucocorticoid receptor-knockout mice present the only animal model for the study of corticosteroid-mediated effects in the complete absence of a functional receptor.     

Effect of bulk flow pulsations on film cooling with compound angle holes

Experiments are conducted to investigate the effects of bulk flow pulsations on film cooling with compound angle holes. A row of five film cooling holes is considered with orientation angles of 0°, 30°, 60°, and 90° at a fixed inclination angle of 35°. Static pressure pulsations are produced by an array of six rotating shutter blades, which extend across the span of the exit of the wind tunnel test section. The pulsation frequency is fixed at 36 Hz, but changes in the time-averaged blowing ratios of 0.5, 1.0 and 2.0 produce three different coolant Strouhal numbers, 3.6, 1.8 and 0.9, respectively. Detailed film cooled boundary layer temperature distributions are measured by a cold wire and the adiabatic film cooling effectiveness by thermochromic liquid crystal (TLC). The boundary layer temperature surveys show that pulsations induce large disruptions to the boundary layer temperature distribution and the film coverage. As the orientation angle increases, the injectant concentration spreads further into the spanwise direction because of pulsations than the steady case. With pulsations the adiabatic film cooling effectiveness value decreases regardless of the orientation angle. The amount of reduction, however, depends on the orientation angle in such a way that the larger the orientation angle is, the smaller the reduction is.     

Ubiquitous Information Services with JAIN Platform

To provide responsive information services in a ubiquitous computing environment, service software and system development are indispensable. A component-based ubiquitous information system with a JAIN (Java APIs for Integrated Networks) platform to achieve seamless transmissions and reach-everywhere communications was designed in our research. In this development, numerous ubiquitous service modules were identified: location management, roaming, mobile IP and WAP networking. These component-based network modules were constructed using a component composition language with component specification and interface definition, running on top of a distributed service architecture using a JAIN platform to distribute the ubiquitous information services to mobile users. Two applications, Wireless-Application-Protocol (WAP) Mail and Video-on-Demand (VoD) services, show that the JAIN-like platform with the developed networking components effectively fills the gap for application developers between mobile appliances and various kinds of ubiquitous information services.