Influence of post‐treatments on the properties of porous poly(vinyl alcohol) membranes

Porous poly(vinyl alcohol) (PVA) membranes were prepared by a phase‐inversion method. The influence of chemical crosslinking and heat treatments on the swelling degree, resistance to compaction, mechanical strength, and morphology of porous PVA membranes was extensively studied. The crosslinking degree and crystallinity of the membranes, calculated from IR spectra, increased with the treatment time. The porosity, calculated on the basis of swelling experiments, showed a decreasing trend for heat‐treated membranes but remained almost at a constant value for crosslinked membranes. Such a change was further proved with scanning electron microscopy pictures. The behavior was explained by the rearrangement of PVA chains during the heat‐treatment process, which led to morphological changes in the membranes. The mechanical properties of the porous membranes in dry and wet states were measured, and a great difference was observed between crosslinked and heat‐treated membranes in the dry and wet states. The crosslinked membranes showed good mechanical properties in the dry state but became fragile in the wet state. On the contrary, the heat‐treated membranes were more flexible in the wet state than in the dry state. This change was explained by the turnaround of inner stress in the systems during the swelling process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Viscoelastic properties of polyarylene ether nitriles/thermotropic liquid crystalline polymer blend

Polyarylene ether nitriles (PEN)/thermotropic liquid crystalline polymer (TLCP) blend was prepared via melt mixing. The immiscible phase morphologies, linear and nonlinear, as well as transient viscoelastic properties of the blend were studied using SEM, rheometer, and DMA. The linear dynamic viscoelastic behavior of the blend shows temperature dependence due to further evolution of the immiscible morphology and, as a result, the principle of time‐temperature superposition (TTS) is invalid. In the steady shear flow, the discrete TLCP phase is difficult to be broken up because of the high viscosity ratio of the blend systems, while is easy to be coarsened and followed by elongation, and finally, to form fibrous morphology at high TLCP content and high shear level. During this morphological evolution process, the transient stress response presents step increase and nonzero residual relaxation behavior, leading to increase of the dynamic viscoelastic responses after steady preshear. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Modeling the effect of pigment morphology on the dynamic compression of coating layers using DEM

In the present paper, discrete element method (DEM) was employed to investigate the effect of pigment morphology on packing dynamics and compressive behavior of paper coating layers in calendering process. Spherical, platy, and needle-like particles, representing GCC, delaminated clay, and aragonite PCC pigments, were considered in this study. For each particle shape, the compression of coating structures formed by mono-sized and poly-dispersed pigments were modeled. Stress–strain behavior of the coating layers and in-plane and out-of-plane movements of the pigment particles during the compression were computed under the same maximum compressive stress. Simulation results revealed that the in-plane movements of the pigment particles during compression in the calender nip were small in magnitude (<0.35 μm). These findings help to better understand the smoothening phenomena of coating structures during the calendering process.     

固体超强酸S_2O_8~(2-)/SnO_2-SiO_2催化合成环己酮1,2-丙二醇缩酮

采用沉淀-浸渍法制备了固体超强酸S2O28-/SnO2-SiO2,以它为催化剂催化环己酮和1,2-丙二醇合成了环己酮1,2-丙二醇缩酮;考察了带水剂种类及用量、酮醇摩尔比、催化剂用量、反应时间对产品收率的影响,并用正交实验对反应条件进行了优化。实验结果表明,适宜的反应条件为:n(环己酮)∶n(1,2-丙二醇)=1∶1.6、催化剂用量为反应物料总质量的2.0%、带水剂环己烷用量5.0mL、反应时间50min。在此条件下,环己酮1,2-丙二醇缩酮收率达到91.47%;催化剂的稳定性良好,在重复使用5次后环己酮1,2-丙二醇缩酮收率为82.20%,活性下降的主要原因为催化剂表面积碳和吸附了有机物;经傅里叶变换红外光谱和气相色谱质谱分析表明,产物为环己酮1,2-丙二醇缩酮,纯度为100%。     

管内覆丝网强化对流换热及阻力特性的实验研究

通过实验对管内覆丝网管进行了强迫对流换热和阻力特性研究。结果表明：管内覆丝网使换热明显增强，阻力也相应增长。菱形丝网对角线距离与平行边距离之比对换热效果有决定作用，丝网厚度对换热的影响比较小，而丝网网格的大小对换热几乎没有影响，在相同的泵功率和几何条件下，换热系数最大增加２１％。     

贝氏体铁素体片条的超微亚结构研究

首次采用扫描隧道显微镜(STM)在大气环境下直接观察了Fe-1.0C-2.0Si-4.0Cr钢中下贝氏体铁素体片条的组织结构,在下贝氏体亚单元内部首次观察到以前从未发现的,尺寸更小、形状规则、排列整齐的结构单元——超亚单元,并初步提出下贝氏体铁素体由以下四个结构层次组成:即下贝氏体铁素体片条由亚片条组成,亚片条由亚单元组成,亚单元由超亚单元组成。     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

平均不等式有趣应用几例

介绍了平均不等式在数学证明中的几例有趣应用。     

JDZ-1型固态存储雨量器降水量误差成因分析

对JDZ-1型固态存储雨量器与虹吸自记雨量计平行观测资料进行了系统分析,分析了两者存在误差的影响因素。对JDZ-1型固态存储雨量器在北方地区使用过程中存在的问题提出了解决方法,以保证和提高JDZ-1型固态存储雨量器资料质量。     

The intervalley X6→Γ6, L6 scattering time in GaAs measured by ultrafast pump-probe infrared absorption spectroscopy

A direct measurement of the dynamics of electrons in the X₆ valley for a GaAs crystal by time-resolved absorption spectroscopy is reported for the first time. IR picosecond probe pulses were used to monitor the growth and decay of the population in the X₆ valley subsequent to excitation by a 527 nm pump pulse. The intervalley X₆→Γ₆, L₆ scattering time t_x of 0.70 ± 0.50 ps is determined and the crossection for the X₆→X₇ transition is estimated to be 1.8 × 10⁻¹⁶ cm².