Call control and traffic transport for connection-oriented highspeed wireless personal communications over metropolitan area networks

A distributed circuit-switched approach for supporting the deployment of high speed wireless personal communication services in urban areas through the interconnection of base stations via metropolitan area networks (MANs) is proposed. Broadband MANs minimize traffic congestion by dynamic sharing of link capacity and by serving as distributed switches for partitioning call control functions. While the DQDB protocol readily supports distributed packet-switching over the IEEE 802.6 MAN, isochronous traffic such as voice and video is best supported by circuit-switched connections. The authors present an enhanced bi-state pre-arbitrated (PA) transport mechanism, and associated call control and handoff management techniques, which enable distributed circuit-switching over the MAN. These capabilities are not currently addressed in the 802.6 standards. The bi-state PA transport mechanism facilitates statistical multiplexing of variable rate isochronous traffic sources. The network capacity is constrained by the call setup delay performance, and is analyzed by simulations. Alternative signaling architectures, involving different placements of call control network elements, are evaluated. The effects of erasure nodes, and close bus versus open bus architectures, are considered. The overlap inter-MAN call setup procedure is proposed to reduce delays. Different call handoff procedures are formulated according to the type of handoff and the resulting change in call connectivity. Most handoffs are intra-MAN, requiring simple procedures with short delays     

Do We Stand on Common Ground? A Threat Appraisal Model for Terror Alerts Issued by the Department of Homeland Security

The fabric and faces of threat, and the expediency and efficiency in the communication of threat, are examined with a threat appraisal model. This model is empirically tested on an ongoing communication challenge, the issuance of terror alerts by the United States' Department of Homeland Security (DHS), focusing on how threat is appraised by both the conservative and liberal audiences. Findings showed a shared view by the DHS and conservative audiences on the levels and nature of threats; liberal audiences thought otherwise. Though there appeared to be a consensus between the conservative and liberal audiences on the efficacy of threat communication, more internal consistency within DHS is needed to optimise its effectiveness.     

Multivariable controller design in an adaptive control scheme

A multivariable control system design approach in the frequency domain is presented. The issue of control system redesign in an adaptive control scheme is discussed. Expert system techniques have been used for the automated design of controllers for multivariable systems. Design knowledge has been represented using rules, facts and objects. The design process consists of a sequence of operations obtained by heuristics and experience in the the design techniques. An automated design session of a multivariable plant using the expert system demonstrates that the expert system appears to work well in its prototype implementation.     

Effect of Stress State on Growth of Interfacial Intermetallic Compounds Between Sn-Ag-Cu Solder and Cu Substrates Coated with Electroless Ni Immersion Au

Excessive intermetallic compound (IMC) growth in solder joints will significantly decrease the reliability of the joints. IMC growth is known to be influenced by numerous factors during the component fabrication process and in service. It is reported that, other than temperature and holding time, stress can also influence the IMC growth behavior. However, no existing method can be used to study the effect of stress state on IMC growth in a controlled manner. This paper presents a novel method to study the effect of stress on interfacial IMC growth between Sn-Ag-Cu solder and a Cu substrate coated with electroless Ni immersion Au (ENIG). A C-ring was used and in-plane bending induced tensile and compressive stresses were applied by tightening the C-ring. Results revealed that in-plane compressive stress led to faster IMC growth as compared with in-plane tensile stress.     

天然气:通向氢能时代的桥梁

文章概述了人类能源利用从柴薪、煤到石油、天然气的探索与转变历程,着重对天然气利用在解决城市燃料和空气污染、提高发电效率、推动分布式发电、生产合成氨和合成甲醇、推动燃料电池转向氢能经济时代等方面的优越性进行了阐述。     

Sensitivity of LR 115 SSNTD in a diffusion chamber

Solid-state nuclear track detectors (SSNTDs), such as LR 115, have been commonly used in diffusion chambers for long-term measurements of radon gas concentrations. For the LR 115 SSNTD, it has been found that the active layer removed during chemical etching is significantly affected by the presence and amount of stirring, and thus cannot be controlled easily. However, the sensitivity of the LR 115 detector inside a diffusion chamber to the radon and/or thoron gas concentration is dependent on the actual removed active layer thickness. This relationship is dependant on the geometry of the diffusion chamber and the deposition fraction of ²¹⁸Po in the diffusion chamber, as well as the V function for the LR 115 detector (V is the ratio between the track etch velocity V_t to the bulk etch velocity V_b). This paper presents the experimentally determined relationships between the sensitivity of the LR 115 detector inside a Karlsruhe diffusion chamber and the removed active layer thickness, for both radon and thoron. A V function was adjusted to simulate the relationships. In particular, for the case of ²²²Rn, we have found f ∼ 0.5, where f is the fraction of ²¹⁸Po which decays inside the diffusion chamber before deposition onto available inner surfaces of the chamber. In conclusion, we have found that the sensitivities critically depend on the actual removed active layer thickness, so this should be monitored and used in determining the sensitivities.     

On a responsive replenishment system: a fuzzy logic approach

In today's competitive business environment, it is important that customers are able to obtain their preferred items in the shops they visit, particularly for convenience store chains such as 7–Eleven where popular items are expected to be readily available on the shelves of the stores for buyers. To minimize the cost of running such store chains, it is essential that stocks be kept to a minimum and at the same time large varieties of popular items are available for customers. In this respect, the replenishment system needs to be able to cope with the taxing demands of minimal inventory but at the same time keeping large varieties of needed items. This paper proposes a replenishment system which is able to respond to the fluctuating demands of customers and provide a timely supply of needed items in a cost–effective way. The proposed system embraces the principle of fuzzy logic which is able to deal with uncertainties by virtue of its fuzzy rules reasoning mechanism, thereby leveraging the responsiveness of the entire replenishment system for the chain stores. To validate the feasibility of the approach, a case study has been conducted in an emulated environment with promising results.     

On agent-mediated electronic commerce

This paper surveys and analyzes the state of the art of agent-mediated electronic commerce (e-commerce), concentrating particularly on the business-to-consumer (B2C) and business-to-business (B2B) aspects. From the consumer buying behavior perspective, agents are being used in the following activities: need identification, product brokering, buyer coalition formation, merchant brokering, and negotiation. The roles of agents in B2B e-commerce are discussed through the business-to-business transaction model that identifies agents as being employed in partnership formation, brokering, and negotiation. Having identified the roles for agents in B2C and B2B e-commerce, some of the key underpinning technologies of this vision are highlighted. Finally, we conclude by discussing the future directions and potential impediments to the wide-scale adoption of agent-mediated e-commerce.