Development of Bigels Based on Stearic Acid–Rice Bran Oil Oleogels and Tamarind Gum Hydrogels for Controlled Delivery Applications

In the last few decades, different types of gels have been widely studied as potential drug delivery carriers. In this paper, we propose the synthesis of an oleogel, a tamarind gum hydrogel, and bigels for applications as drug delivery matrices. The oleogel was prepared by mixing stearic acid and rice bran oil, whereas the hydrogel was prepared by mixing tamarind gum with a hydroethanolic solution. Hydrogel‐in‐oleogel and oleogel‐in‐hydrogel bigels were prepared by mixing the hydrogel and the oleogel. The suitability of the formulations for controlled drug release applications was thoroughly examined using microscopy, Fourier transform infrared (FTIR) spectroscopy, as well as mechanical, electrical, thermal, drug release, and antimicrobial studies. An alteration in the microarchitecture of the bigels is observed when the oleogel and the hydrogel are mixed in varying proportions. The associative interactions within the formulations increase with the increase in the hydrogel content. The bigels exhibit the presence of stearic acid melting endotherm (associated with the oleogel) and water evaporation endotherm (associated with the hydrogel). This study suggests that the hydrogel has lowest bulk resistance compared to the other formulations. The structural breakdown of the bigels is composition‐dependent, and the bulk electrical resistance is mainly governed by the oleogel phase. An increase in the diffusion of the moxifloxacin HCl from the formulations is observed with the increase of the hydrogel proportion, which in turn increases the rate of release of the drug. The proposed formulations also exhibit good antimicrobial efficacy. The analysis of these properties suggests that specific formulations can be tailored by need‐based applications of the drug release rate.     

Determination of gamma-emitting radionuclides in the inter-tidal sediments off Balochistan (Pakistan) Coast, Arabian Sea

Natural radionuclide contents of 226Ra, 228Ra and (40)K were studied for inter-tidal sediments collected from selected locations off the745 km long Balochistan Coast using HPGe detector based gamma-spectrometry system. The sampling zone extends from the beaches of Sonmiani (near Karachi metropolis) through Jiwani (close to the border of Iran). The natural radioactivity levels detected in various sediment samples range from 14.4 +/- 2.5 to 36.6 +/- 3.8 Bq kg(-1) for 226Ra, 9.8 +/- 1.2 to 35.2 +/- 2.0 Bq kg(-1) for (228)Ra and 144.6 +/- 9.4 to 610.5 +/- 23.9 Bq kg(-1) for (40)K. No artificial radionuclide was detected in any of the marine coastal sediment samples. 137Cs, (60)Co, 106Ru and 144Ce contents in sediment samples were below the limit of detection. The measured radioactivity levels are compared with those reported in the literature for coastal sediments in other parts of the world. The information presented in this paper will serve as the first ever local radioactivity database for the Balochistan/Makran Coastal belt of Pakistan. The presented data will also contribute to the IAEA's, Asia-Pacific Marine Radioactivity Database (ASPAMARD) and the Global Marine Radioactivity Database (GLOMARD).     

No evidence for an ischemic penumbra in massive experimental intracerebral hemorrhage

OBJECTIVES: To determine the effect of massive intracerebral hemorrhage (ICH) on regional cerebral blood flow (rCBF) and metabolism, and to test the hypothesis that there is persistent ischemia in the perihematoma region after ICH. BACKGROUND: Cerebral ischemia is postulated to be one of the mechanisms of neural injury after ICH. Presumably the hematoma induces ischemia by mechanical compression of the surrounding microvasculature. METHODS: The authors induced ICH in eight anesthetized mongrel dogs by autologous blood injection (7.5 mL) under arterial pressure in the deep white matter adjacent to the left basal ganglia. They measured serial rCBF using radiolabeled microspheres in regions around and distant to the hematoma, as well as cerebral oxygen extraction, oxygen consumption (CMRO2), glucose utilization, and lactate production by serial sampling of cerebral venous blood from the sagittal sinus. Mean arterial pressure (MAP) and intracranial pressure (ICP) were monitored continuously. All measurements were recorded at 0.5, 1.0, 2.0, 3.5, and 5.0 hours after induction of ICH and compared with prehematoma values. Evans Blue dye was injected at the end of the experiment, and intensity of staining was compared with three control animals. RESULTS: Compared with prehematoma ICP (12.5+/-2.0 mm Hg, mean+/-standard error), significant elevation in ICP was observed after ICH peaking at 5 hours (34.4+/-5.2 mm Hg). Compared with prehematoma MAP (125.8+/-7.0 mm Hg), significant elevation in MAP was observed at 120 minutes after onset of hematoma (139.1+/-4.6 mm Hg), with return to the prehematoma value by 5 hours. There were no significant changes observed in cerebral oxygen extraction (51.4+/-4.3% versus 44.8+/-4.9%) and CMRO2 (1.8+/-0.3 versus 1.64+/-0.2 mL O2/100 g/min) at 5 hours posthematoma (or any other posthematoma measurement) compared with prehematoma values. There were no significant differences observed in rCBF in the perihematoma gray (18.2+/-0.9 mL/100 g/min versus 20.1+/-1.5 mL/100 g/min) or white matter (15.6+/-1.4 mL/100 g/min versus 15.3+/-1.1 mL/100 g/min) at 5 hours posthematoma (or any other posthematoma measurement) compared with prehematoma values. No changes were observed in cerebral glucose utilization, lactate production, and rCBF in other regions after introduction of ICH. Permeability of the blood-brain barrier was more prominent in the ipsilateral hemisphere in animals with ICH compared with control animals. CONCLUSIONS: Despite a prominent increase in ICP and MAP after ICH, the authors found no evidence to support the presence of an ischemic penumbra in the first 5 hours after ICH. Thus, other mechanisms for acute neural injury and late rCBF changes after ICH must be investigated.     

A comprehensive design and rating study of evaporative coolers and condensers. Part I. Performance evaluation

The mathematical models of evaporative fluid coolers and evaporative condensers are studied in detail to perform a comprehensive design and rating analysis. The mathematical models are validated using experimental as well as numerical data reported in the literature. These models are integrated with the fouling model presented in an earlier paper, using the experimental data on tube fouling. In this paper, we use the fouling model to investigate the risk based thermal performance of these evaporative heat exchangers. It is demonstrated that thermal effectiveness of the evaporative heat exchangers degrades significantly with time indicating that, for a low risk level (p=0.01), there is about 66.7% decrease in effectiveness for the given fouling model. Furthermore, it is noted that there is about 4.7% increase in outlet process fluid temperature of the evaporative fluid cooler. Also, a parametric study is performed to evaluate the effect of elevation and mass flow rate ratio on typical performance parameters such as effectiveness for rating calculations while surface area for design calculations.     

Changes in circulating biomarkers during a single hemodialysis session

The hemodialysis (HD) procedure induces an inflammatory response potentially contributing to cardiovascular disease. Here we investigated the acute impact of HD on circulating biomarkers. Circulating biomarkers (small solutes, middle molecular‐sized peptides, and proteins) related to inflammation, oxidative stress, and vascular calcification (VC) were measured before and after a single session of HD in 45 clinically stable patients. Concentrations were corrected for ultrafiltration‐induced hemoconcentration. Among vascular calcification‐related biomarkers, osteoprotegerin and fetuin‐A remained unchanged while fibroblast growth factor‐23 (FGF23) decreased by ?19%. Changes of FGF23 and changes of phosphate correlated (ρ = 0.61, P < 0.001). While C‐reactive protein did not change, interleukin‐6 (IL‐6) increased by 14% and pentraxin 3 (PTX3) increased by 45%. IL‐6 and PTX3 appear to be valid biomarkers of the intradialytic inflammatory response. VC‐related markers were in general not affected by the single HD session; however, the observed correlation between acute changes of FGF‐23 and phosphate during HD warrants further studies.     

Determination of ranged sets of design specifications by incorporating design-space heterogeneity

Setting design specifications (targets) is a critical task in the early stages of the design process. Flexible targets can accommodate uncertainty and changes in design by postponing design commitments and preserving design freedom. In this article, a new method is developed for obtaining a ranged set of design specifications that meets design criteria whilst incorporating design-space heterogeneity; meaning some areas in the design attribute space are more achievable than the others. The proposed method has two notable features. First, a quantization algorithm based on rough-set theory is used to decompose a design attribute space into sub-regions on the basis of how well they meet design criteria. Second, a new design-flexibility measure is used as a metric to select the most desired ‘target region’ on the bases of both the size of the region and the influence of potential design alternatives on overall achievability. The proposed approach enhances the capacity of a design system to adapt to evolving design knowledge, as well as to unexpected changes. The proposed method is demonstrated by a numerical example and the design of a domestic blender.     

Power aware channel width tapering of serially connected MOSFETs

This paper reviews a transistor channel width tapering scheme called Hill Tapering for FET chains with specific emphasis on power dissipation and layout area of the tapered chains. The Hill Tapering scheme results in the lowest power dissipation and physical area compared to any of the existing tapering schemes like linear, exponential or optimal tapering. It also offers high speed operation. This tapering scheme is general and suits domino logic circuit designs. SPICE simulation results have shown that up to 81% power dissipation reduction could be achieved by using this tapering scheme.     

Study of relaxations in poly(methyl methacrylate)–magneto electrets by thermally stimulated depolarization current and surface‐charge‐decay mechanisms

The effect of the forming temperature and the magnetic field was investigated for the charge retention and stability of poly(methyl methacrylate) (PMMA)–magneto electret (ME) samples with thermally stimulated discharge currents (TSDCs) and a surface‐charge‐decay mechanism. The measurements were performed on a pristine PMMA sample with a thickness of 20 mm. The comparative studies of charge decay with TSDC indicated a strong resemblance between the results of the two techniques of MEs of PMMA and were characterized by two TSDC peaks, that is, an α peak at 110°C and a ρ peak at 160°C. The low‐temperature peak (i.e., the α peak) was associated with dipolar relaxation, and the high‐temperature peak (i.e., the ρ peak) was attributed to the self‐motion of space charges in PMMA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Weather-Induced Degradation of Plastic Pipes

A number of plastic materials, such as unplasticized poly(viny1 chloride) (uPVC), acrylonitrile-butadiene-styrene (ABS), high-density polyethylene (HDPE), poly-(vinylidene fluoride) (PVDF), and chlorinated poly(viny1 chloride) (cPVC), are available for numerous applications. uPVC and HDPE pipes are used in pressurized piping systems in Saudi Arabia for industrial, agricultural, domestic, and general-purpose applications. Some studies have been carried out to investigate the causes of failure in plastic pipes, which is very high in the area. In this chapter an overview of the failure of plastic pipes is presented, with emphasis given to failure of pipes due to severe weather conditions in Saudi Arabia.