Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Continuous phase quadrature phase shift keyed signaling techniquewith coding

A continuous phase quadrature phase shift keyed (CPQPSK) modulation technique is presented. This method utilizes a conventional QPSK modulator and a phase trajectory converter to approximate M=4, h=1/4 continuous phase signal and allows low cost, low complexity, and high rate (>1 Gbit/s) CPM modem implementation for bandwidth efficient transmission through nonlinear satellite channels. Using a communications analysis computer program it has been found that CPQPSK has 99 percent out-of-band power of 0.8R (MSK has 99 percent out-of-band power of 1.2 R where R is defined as bit rate), continuous phase trajectories, and nearly constant envelope amplitude. Simulation of realistic hardware designs indicate that the CPQPSK will require an Eb/No of 14 dB to achieve a bit error rate (BER) of 10^-6. Forward error correcting techniques using block codes with an overhead of 10 percent indicate that the Eb/No requirements can be reduced to 11.2 dB for 10^-6 BER     

Two-fluid large-eddy simulation approach for particle-laden turbulent flows

In this paper, effects of particles on the subgrid scales of turbulence are properly accounted for during the modeling of subgrid scale stresses in the large-eddy simulation (LES) of fluid phase. In doing so, we propose closed filtered kinetic equations for phase space density of the particle. The various moments of these equations give the `fluid' equations which can be considered as the LES equations for the particle phase. The influence of subgrid scales motion on the particles is included in these `fluid' equations.     

Theoretical analysis of control properties for the brushless doubly fed reluctance machine

The brushless doubly fed induction machine (BDFIM) has been extensively researched for approximately 30 years, but a related machine [the brushless doubly fed reluctance machine (BDFRM)], has not. This was mainly due to the fact that reluctance rotor designs were not capable of generating saliency ratios large enough to make the BDFRM competitive with other machines. However, recent developments in reluctance rotors, spurred on by research into synchronous reluctance machines, has resulted in high saliency ratio rotors that are economic to build. This, together with the promise of higher efficiency and simpler control compared to the BDFIM, means that further investigation of the BDFRM is warranted. A relatively limited amount of work to date has been published on the BDFRM. This paper attempts to fill this void by presenting a theoretical analysis of some of the important control properties of the ideal BDFRM.     

Performance and modeling of advanced Ti:LiNbO3 digitaloptical switches

High-performance Y-branch digital optical switches realized in Ti:LiNbO₃ are presented. Their switching response functions have been optimized in terms of switch voltage and crosstalk ratio. The optimization is based on analyzing different types of waveguide shaping and switching arrangements using coupled mode theory and computer simulations. Excellent switching characteristics are achieved with devices exploiting a specially shaped waveguide branch in a dilated switch arrangement. Demonstrated performances include switching voltage as low as 9 V with crosstalk suppression better than 45 dB and fiber-to-fiber losses as low as 4 dB. Polarization independence with crosstalk suppression better than 40 dB over a 1520- to 1570-nm wavelength range is achieved for any applied switch voltage greater than 18 V. These optimized digital optical switches have further demonstrated the capability to reshape electrical input signals at switching rates of several hundred megahertz     

Synthesis, 1H−NMR and Electronic Absorption Spectra,and Halochromic Properties of Bis(2-methyl-1-phenyl-3-isoindolyl)-(het)arylmethane Dyes

Several bis(2-methyl-1-phenyl-3-isoindolyl)-(het)arylmethane perchlorate dye salts have been synthesised, the (het)aryl substituent representing the acceptor systems 2-benzothiazolyl, 1-methyl-2-benzimidazolyl, 4-quinolyl, 4- and 2-pyridyl as well as phenyl.The constitution of these green dye salts was supported by their ¹H-NMR spectra. The variation of the electronic absorption maxima of this dye series was in accord with theoretical considerations based on SCF-CI and PMO calculations. They give rise to the statement that the bathochromic effect of the varied (het)aryl group is essentially due to a LUMO-LUMO interaction with the di-isoindolylmethane cyanine moiety, i.e. a second-order perturbation, enlarging the bathochromic shift caused by the increased twist angles inflicted on the central bonds by the bulkiness of the (het)aryl substituents (a first-order perturbation). The halochromic properties of these dyes are explicable on the same basis.The dissociation constants pK^★ and pK^★_R+ were measured and compared with analogous di-indolyl- (1) and di-indolizinyl-hetaryl-methane dyes (4), showing little difference with regard to the former and the distinct sequence indolizinyl > indolyl > isoindolyl dye series for the latter.     

Is Chlorogenic Acid Bitter?

Chlorogenic acid at 5° published threshold concentration (100 mg/ L) in aqueous 0.2% potassium acid tartrate was not significantly more bitter than aqueous 0.2% potassium tartrate alone when evaluated by taste panel.