Reduced and differential parallel interference cancellation forCDMA systems

Since code division multiple access systems in multipath environments suffer from multiple access interference (MAI), multiuser detection schemes should be used in the receivers. Parallel interference cancellation (PIC) is a promising method to combat MAI due to its relatively low computational complexity and good performance. It is shown that the complexity of PIC is still high for realistic scenarios in terms of the symbol rate, the number of users, spreading gain, and multipath components. However, two novel methods are introduced to reduce significantly the complexity without sacrificing performance. The first approach, called reduced PIC, takes advantage of the composition of the interference to concentrate interference cancellation only on significant terms. The second approach, called differential PIC, exploits the multistage character of PIC to avoid unnecessary double calculations of certain terms in consecutive stages. It is shown that a combination of both approaches leads to a performance very close to the single-user bound whereas the complexity can be kept on the order of the conventional RAKE receiver     

Deformation behavior of HCP Ti-Al alloy single crystals

Single crystals of Ti-Al alloys containing 1.4, 2.9, 5, and 6.6 pct Al (by weight) were oriented for 〈a〉 slip on either basal or prism planes or loaded parallel along the c-axis to enforce a nonbasal deformation mode. Most of the tests were conducted in compression and at temperatures between 77 and 1000 K. Trace analysis of prepolished surfaces enabled identification of the twin or slip systems primarily responsible for deformation. Increasing the deformation temperature, Al content, or both, acted to inhibit secondary twin and slip systems, thereby increasing the tendency toward strain accommodation by a single slip system having the highest resolved stress. In the crystals oriented for basal slip, transitions from twinning to multiple slip and, finally, to basal slip occurred with increasing temperature in the lower-Al-content alloys, whereas for Ti-6.6 pct Al, only basal slip was observed at all temperatures tested. A comparison of the critically resolved shear stress (CRSS) values for basal and prism slip as a function of Al content shows that prism slip is favored at room temperature in pure Ti, but the stress to activate these two systems becomes essentially equal in the Ti-6.6 pct Al crystals over a wide range of temperatures. Compression tests on crystals oriented so that the load was applied parallel to the c-axis showed extensive twinning in lower Al concentrations and 〈c+a〉 slip at higher Al concentrations, with a mixture of 〈c+a〉 slip and twinning at intermediate compositions. A few tests also were conducted in tension, with the load applied parallel to the c-axis. In these cases, twinning was observed, and the resolved shear for plastic deformation by twinning was much lower that that for 〈c+a〉 slip observed in compression loading. This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science and Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Effects of seat slope and hip flexion on spinal angles in sitting

Lumbar and thoracic spinal angles of 25 male and 25 female subjects were measured in four sitting postures, with standing angles used as reference. Subjects sat with either 90 deg or 65 deg of hip flexion on either flat or forward-sloping seats. Lumbar kyphosis was greatest when the flat seat/90-deg posture was adopted and least when the sloping seat/65-deg posture was adopted. The opposite was observed for the thoracic angles, and intermediate results were observed for the other two sitting postures. No statistically significant interactions were observed among seat slope, hip flexion, and subject sex. The findings are discussed with reference to the anatomy of sitting and factors influencing pelvic tilt and the implications for the ergonomic design of chairs.     

Coarse filters for shape matching

This article describes the coarse shape filters that support the 3D, Internet-based search engine ShapeSifter, which aims to locate parts already in production that have a shape similar to a desired new part. The search engine analyzes the target model's shape characteristics and performs a similarity match on the database's contents. Our main challenge is identifying shape metrics that produce effective characterizations of 3D models for similarity comparison. We focus on using three novel convex hull-based indices to carry out a preliminary coarse filtering of candidates prior to more detailed analysis. We also describe the crucial role played by two databases of benchmark objects. Unlike other shape-matching systems, we chose ShapeSifter's architecture (multistep query), 3D representation (triangulated mesh), and implementation (Java3D) to allow deployment online once it matures     

Eliminating memory for fragmentation within partitionable SIMD/SPMDmachines

Efficient data layout is an important aspect of the compilation process. A model for the creation of perfect memory maps for large-scale parallel machines capable of user-controlled partitionable single-instruction-multiple data/single-program-multiple data (SIMD/SPMD) operation is developed. The term perfect implies that no memory fragmentation occurs and ensures that the memory map size is kept to a minimum. A major constraint on solving this problem is based on the single program nature of both the SIMD and SPMD modes of parallelism. It is assumed that all processors within the same submachine used identical addresses to access corresponding data items in each of their local memories. Necessary and sufficient conditions are derived for being able to create perfect memory maps, and results are applied to several partitionable interconnection networks