Factors influencing feature usage in work-related communication

Two studies are presented. The first aimed to identify possible barriers to the uptake and use of commonly available telephony features and to determine whether greater knowledge of features/access codes and availability of user manuals could increase feature usage under certain conditions. Results showed that feature-usage patterns were not affected by any of the manipulations, but that they were determined by specific job demands. Using Constantine and Lockwood's (1999) conceptualization of user roles, a method to support feature bundling decisions for specific target markets was developed and tested in the second study. The method - Strategic User Needs Analysis (SUNA) - was shown to yield a useful balance between high- and low-level information about selected roles. SUNA provided sufficient information to distinguish between PDA feature usage patterns of two similar target user groups as well as to suggest additional features each of the two target groups would find useful. The development of SUNA and observational findings of actual PDA usage are reported.     

Softwarekartographie

Zusammenfassung  Anwendungslandschaften in Unternehmen sind langlebige hoch-komplexe Strukturen bestehend aus hunderten bis tausenden von miteinander vernetzten betrieblichen Informationssystemen, die von Personen mit sehr unterschiedlichen Interessen und Erfahrungshintergrund konzipiert, erstellt, modifiziert, betrieben, genutzt und finanziert werden. Die Softwarekartographie zielt darauf ab, die Kommunikation zwischen diesen Personen durch zielgruppenspezifische verst?ndliche graphische Visualisierungen zu unterstützen, die Gesch?fts- und Informatik-Aspekte gleicherma?en berücksichtigen, und die speziell für langfristige und strategische Management-Betrachtungen geeignet sind. In diesem Beitrag fassen wir zun?chst die in der betrieblichen Praxis wohlbekannten Probleme beim Management von Anwendungslandschaften zusammen und diagnostizieren erhebliche Kommunikationsdefizite. Da Anwendungslandschaften als Systeme von Systemen mit Menschen als integrale Systembestandteile zu verstehen sind, werden Karten als attraktiver L?sungsansatz identifiziert und die wesentlichen Konzepte der Softwarekartographie anhand von Beispielen vorgestellt. Dabei werden Querbezüge zu anderen Fachgebieten der Informatik und Wirtschaftsinformatik hergestellt, und die bisherige Nutzung der Forschungsergebnisse in der Praxis gezeigt.     

Driving Mechanisms of Delamination Related Reliability Problems in Exposed Pad Packages

Exposed pad packages were introduced in the late 1980s and early 1990s because of their excellent thermal and electrical performance. Despite these advantages, the exposed pad packages experience a lot of thermo-hygro-mechanical related reliability problems during qualification and testing. Examples are die lift, which occurs predominantly after moisture sensitivity level conditions, and die-attach to leadframe delamination leading to downbond stitch breaks during temperature cycling. In this chapter, nonlinear finite element (FE) models using fracture mechanics based J-integral calculations are used to assess the reliability problems of the exposed pad package family. Using the parametric FE models any geometrical and material effects can be explored to their impact on the occurrence diepad delamination, and dielift. For instance the impact of diepad size is found to be of much less importance as the impact of die thickness is. Using the fracture mechanics approach, the starting location for the delamination from thermo-hygro-mechanical point of view is deducted. The results indicate that when diepad delamination is present, cracks are likely to grow beneath the die and dielift will occur. The interaction between dielift and other failure modes, such as lifted ball bonds, are not found to be very significant. The FE models are combined with simulation-based optimization methods to deduct design guidelines for optimal reliability of the exposed pad family.     

Grouped Approach for the Design of H.264/AVC Motion Estimation Architectures

This letter presents a novel approach for organizing computational resources into groups within H.264/AVC motion estimation architectures, leading to reductions of up to 75% in the equivalent gate count with respect to state‐of‐the‐art designs.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Tri-Gate Bulk MOSFET Design for CMOS Scaling to the End of the Roadmap

A tri-gate bulk MOSFET design utilizing a low-aspect-ratio channel is proposed to provide an evolutionary pathway for CMOS scaling to the end of the roadmap. 3-D device simulations indicate that this design offers the advantages of a multi-gate FET (reduced variability in performance and improved scalability) together with the advantages of a conventional planar MOSFET (low substrate cost and capability for dynamic threshold-voltage control).     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Impact of the addition of an enzyme pool on an activated sludge system treating dairy wastewater under fat shock loads

BACKGROUND: The application of lipase‐rich enzyme pools (such as the crude solid enzymatic preparation (SEP) obtained from Penicillium restrictum solid‐state fermentation of agro‐industrial wastes) to activated sludge systems may be an effective strategy for preventing various operational problems. The continuous addition of SEP to the treatment system can become cost‐prohibitive when in situ production and/or storage are factored in. The application of SEP to high‐fat wastewater treatment would only be justified as an emergency measure, such as a sudden increase in the fat content of the bioreactor influent. Therefore, the primary objective of this work was to investigate the efficiency of a crude SEP during fat shock loads, simulated through the periodic addition of dairy industry waste containing high fat concentrations to the feed stock of an activated sludge system, operated in continuous mode. RESULTS: The test bioreactor exhibited a higher average chemical oxygen demand (COD) removal efficiency than the control bioreactor (83% for control and 90% for test) and the fat accumulation in the biological flocs of the test bioreactor was 3.2 times lower than that in the control bioreactor. Turbidity was also lower in the effluent of the test bioreactor (123 and 66 FTU in control and test, respectively) and it had a shorter recovery time between shock loads, especially when the interval between loads was shorter than one month (biweekly and weekly shock loads). CONCLUSION: The addition of SEP during fat overloads in the reactor feed maintained efficient COD removal in the test bioreactor for 270 days without any operational problems. Copyright © 2008 Society of Chemical Industry     

Recrystallization of phenylbutazone using supercritical fluid antisolvent process

Phenylbutazone was recrystallized from its solutions by using a supercritical fluid antisolvent process. It was dissolved in acetone and supercritical carbon dioxide was injected into the solution, thereby inducing supersaturation and particle formation. Variation in the physical properties of the recrystallized phenylbutazone was investigated as a function of the crystallizing temperature and the carbon dioxide injection rate. The recrystallized particles showed cleaner surfaces and more ordered morphology compared to the particles obtained by other methods such as solvent evaporation. X-ray diffraction patterns indicated that the crystallinity of the particles had been modified upon the recrystallization. Differential scanning calorimetry measurement revealed that the crystallizing temperature influenced the thermal stability of the resulting crystals. Larger crystals were produced when the carbon dioxide injection rate was reduced.     

An adaptive tracking problem for a family of retarded time-delay plants

Most of the existing switching control techniques are developed specifically for finite-dimensional linear time-invariant (LTI) systems. In many practical applications, however, it is essential to take time delay into consideration in the modelling as the control system can be highly sensitive to delay. In this paper, a multi-model switching control algorithm is proposed for retarded time-delay systems. It is assumed that the plant is represented by a family of known multi-input multi-output, observable, LTI models with multiple delays in the states, and that corresponding to each model in the known family, there exists a high-performance finite-dimensional LTI controller. In addition, it is supposed that a bound on the magnitude of the external inputs and disturbances is available. It is then shown that the proposed switching controller can stabilize the uncertain system, and that under some mild conditions, output tracking can be achieved in the given problem setting. Copyright © 2007 John Wiley & Sons, Ltd.