Electronic gate detection for cell or particle counting and sizing in liquids: front-end characteristics, flow-dependent gate impedance, and its remediation

The detection sensitivity and the sizing resolution of electronic gating are inherently limited by fluctuating gate impedance and flow-induced noise. Instabilities of this type, as shown, are due to varying flow patterns of the carrier liquid beyond the gate. Their effects, although largely hidden in dc-operated gating, cause broadening and shift of cell/particle-size distributions under measurement. RF-operated gating, more specifically the demodulation operation, is much more hindered. For an investigation of these effects, a physical model is proposed along with a procedure for the identification of the system parameters. A detector of dedicated concept is used for evaluating the model, and, more specifically, for investigating the impact of configurational and hydrodynamic parameters. Experiments prove that the origin of flow-dependent gate impedance is to be located inside a zone of only a few-micrometer extent at the gate outlet. This is confirmed by the calculated electric field patterns. On such grounds, electrode configurations are proposed that minimize the current density in the zone of hydrodynamic instability and, hence, the flow-induced noise. The same configurations also minimize the impedance of the gate as signal source, facilitating broadband operation, and multifrequency cell impedance measurements.     

Development of a predictive model for polymer/solvent diffusion coefficient calculations

A new calculation procedure for free‐volume parameters is considered in this work by using viscosity prediction methods and the Levenberg‐Marquardt calculation scheme. All parameters used in the Vrentas–Duda free‐volume theory can be estimated from pure component properties. The prediction results are compared with experimental data for some polymer/solvent systems. The diffusion coefficient calculated by Vrentas–Duda theory can be used in the modeling of membrane separation processes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Use of postconsumer polyethylene in blends with polyamide 6: Effects of the extrusion method and the compatibilizer

Blends of polyamide and high‐density polyethylene show adequate properties for a large range of applications: they are used for the production of filaments, containers, and molding resins. The effect of the addition of 2 wt % of a compatibilizer, maleic anhydride grafted polyethylene, to the blend was studied and compared to the use of postconsumer polyethylene. The samples were extruded with single‐ and twin‐screw extruders with 25, 50, or 75 wt % f polyethylene, and the test specimens, molded by injection, were characterized by stress–strain tests, thermal properties, and morphologies. Processing the blends with postconsumer polyethylene in both extruders improved the mechanical properties in comparison to the blends processed with high‐density polyethylene and the compatibilizer. The morphologies of these blends showed that there was a decrease in the domain size of the disperse phase with the use of the compatibilizer or postconsumer polyethylene. The results indicate that for this blend, postconsumer polyethylene substituted, with advantages, for the necessity of a compatibilizer and the use of the high‐density polyethylene. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Comparative Study of Models on Confinement of Concrete Cylinders with Fiber-Reinforced Polymer Composites

The use of fiber-reinforced polymer (FRP) composites for strengthening and/or rehabilitation of concrete structures is gaining increasing popularity in the civil engineering community. One of the most attractive applications of FRP materials is their use as confining devices for concrete columns, which may result in remarkable increases of strength and ductility as indicated by numerous published experimental results. Despite a large research effort, a proper analytical tool to predict the behavior of FRP-confined concrete has not yet been established. Most of the available models are empirical in nature and have been calibrated against their own sets of experimental data. On the other hand, the experimental results available in the literature encompass a wide range of values of the significant variables. The objective of this work is a systematic assessment of the performance of the existing models on confinement of concrete columns with FRP materials. The study is conducted in the following steps: the experimental data on confinement of concrete cylinders with FRP available in the technical literature are classified according to the values of the significant variables; the existing empirical and analytical models are reviewed, pointing out their distinct features; the whole set of available experimental results is compared with the whole set of analytical models; and strengths and weaknesses of the various models are analyzed. Finally, a new equation is proposed to evaluate the axial strain at peak stress of FRP-confined concrete cylinders.     

Hybrid finite-element method for discretising cylindrically symmetric parts in electrotechnical models

In many technical devices such as transformers and electrical machines, large differences in geometric dimensions are observed. As a consequence, the generation of a 3D computational grid for the whole device leads to unacceptably large numbers of elements or can even fail. In addition to the commonly applied cartesian or cylindrical symmetries of the overall geometry, the model can be subdivided into parts featuring translational or cylindrical symmetries. Such parts are discretised separately, accounting for the local symmetry, and are then combined with the surrounding 3D model. Excitations and boundary conditions of the submodels are not necessarily symmetric but are expected to be smooth in the direction of the symmetry. Then, the field distribution at the interface is well approximated by a set of spectral elements along the dimension of symmetry. Coupling between the model parts is carried out by means of Lagrange multipliers. A single-phase transformer with thin insulation sheets is taken as an example to illustrate the proposed hybrid discretisation. The cross-section of the cylindrically symmetric part containing thin sheets, is represented by a fine 2D finite-element mesh so that all the geometrical details can be resolved, and the rest of the structure is discretised by a 3D mesh. Nevertheless, a fully 3D field distribution is calculated in all model parts. Only a small number of harmonic functions is needed to account for the azimuthal field variation at the cylindrical interface. Hence, the number of unknowns in the numerical model is reduced significantly, while a high level of accuracy is maintained     

MC3D-3D continuum radiative transfer, Version 2

A revised and greatly improved version of the 3D continuum radiative transfer code MC3D is presented. It is based on the Monte Carlo method and solves the radiative transfer problem self-consistently. It is designed for the simulation of dust temperatures in arbitrary geometric configurations and the resulting observables: spectral energy distributions, wavelength-dependent images, and polarization maps. The main objective is the investigation of “dust-dominated” astrophysical systems such as young stellar objects surrounded by an optically thick circumstellar disk and an optically thin(ner) envelope, debris disks around more evolved stars, asymptotic giant branch stars, the dust component of the interstellar medium, and active galactic nuclei.     

Caught between historical experience and high hopes: automation atthe Dutch Postal Cheque and Clearing Service, 1950-1965

Since the Netherlands lacks an indigenous computer industry, the article concentrates on the use of computing technologies. It deals specifically with the Dutch giro system, the country's initial step toward automation in the early 1950s. Automation was achieved in 1965. Several organizational processes and the development of computer technology throughout the fifties contributed to the delay of automation and the ultimate choice and implementation of more than 20 IBM 1401 computer systems. The paper sheds light on the importance of studying how computer technology is used as well as how the technologies are developed