西澳坎巴尔达镍矿床滴状硫化物的成因

分布在坎巴尔达许多富矿体中的滴状矿石,是德坑和阿托矿区的主要矿石类型,目前对其成因争论较大。根据矿物共生组合及在相图中的位置、典型的矿石结构构造、硫化镍中钴元素及铂族元素的含量、滴状矿石中硅酸盐矿物成分与基质中相应矿物成分对比等推测,滴状硫化物是从硅酸盐溶浆中分凝出的磁黄铁矿-镍黄铁矿-黄铜矿溶浆在低温和富硫条件下,又重新组成针镍矿-紫硫镍矿-黄铁矿溶浆分凝出的。对几个钻孔剖面详细的岩性、橄榄石形状、粒度等系统研究发现,滴状硫化物富集在某些岩浆旋回的上部近鬣刺结构层,形成于岩浆流动过程中,以致可携带较大的(1～3cm)镍硫化物液滴在岩浆旋回的上部结晶而不沉入底部。     

Performance characteristics of an axial-flow gas induction impeller

Power number, pressure coefficient, and induced gas flow rate of a novel axial-flow gas induction impeller with large openings for gas flow are reported. The effects of rotational speed, impeller diameter, submergence, and pumping mode are considered in turbulent operation. The pressure coefficient is measured using the reduction in pressure at speeds below the minimum induction speed as well as from the minimum induction speed. The minimum induction speed approach consistently yields lower pressure coefficient values, indicating the existence of impeller exit losses that are required to force gas from the centre of the impeller into the liquid. The induced gas flow rate is modelled using two approaches. The first approach relates the gas flow rate to the available pressure difference, and in this case, the relation is found to be strongly affected by impeller diameter. The second approach is a literature model that likens the induction process to water jet injection. While this approach appears promising, flow measurement device pressure losses make it difficult to definitively evaluate this method.     

Essentiality of dietary ω3 fatty acids for premature infants: Plasma and red blood cell fatty acid composition

Pre-term infants, that are not breast-fed, are deprived of vital intrauterine fat accretion during late pregnancy and must rely on formula to obtain fatty acids essential for normal development, particularly of the visual system. Preterm infants (30 wk postconception) receiving human milk were compared to infants given one of the following formulae: Formula A was a commercial preterm formula with predominantly 18∶2ω6 (24.2%) and low (0.5%) 18∶3ω3; Formula B was based on soy oil and contained similar 18∶2ω6 levels (20%) and high 18∶3ω3 (2.7%); Formula C was also a soy oil-based formula (20% 18∶2, 1.4% 18∶3) but was supplemented with marine oil to provide ω3 long-chain polyunsaturated fatty acids (LCP) at a level (docosahexaenoic acid, DHA, 0.35%) equivalent to human milk. At entry (10 days of age), the fatty acid composition of plasma and red blood cell (RBC) membrane lipids of the formula groups were identical. By 36 wk postconception, the DHA content in lipids of group A was significantly reduced compared to that in the human milk and marine oil formula groups. Omega-3 LCP results were further amplified by 57 wk with compensatory increases in 22∶5ω6 in both plasma and RBC lipids. Provision of 2.7% α-linolenic acid in formula group B was sufficient to maintain 22∶6ω3 levels equivalent to those in human milk-fed infants at 36 wk but not at 57 wk. Effects on the production of thiobarbituric acid reactive substances and fragility of RBC attributable to the marine oil supplementation were negligible. The results support the essentiality of ω3 fatty acids for preterm infants to obtain fatty acid profiles comparable to infants receiving human milk. Formula for preterm infants should be supplemented with ω3 fatty acids including LCP. Based on a paper presented at the Symposium on Milk Lipids held at the AOCS Annual Meeting, Baltimore, MD, April 1990.     

Coupling granule properties and granulation rates in high-shear granulation

It is possible to link granulation rates to granule properties. The linkage is by multiple dimension population balance equations that, by means of simplifying assumptions, can be reduced to multiple one-dimensional (1-D) population balance equations (PBEs). Using simple physically based models, this paper demonstrates how multiple one-dimensional population balance equations can describe the results of high-shear granulation experiments of two different materials, calcium carbonate and lactose. Good agreement between experimental and simulated results was achieved enabling the granulation rates to be defined by two model parameters: the critical binder volume fraction and the aggregation rate constant. The modelling framework presented in this paper also provides a basis for the kinetic analysis of granulation experiments so that with further work, it is possible to determine the effect of process conditions and material properties on the model parameters.     

Preparation and characterization of trilobal activated carbon fibers

The objective of this research was to evaluate the effectiveness of several different methods for controlling the pore size and pore size distribution in activated carbon fibers. Variables studied included fiber shape, activation time, and the addition of small amounts of silver nitrate. Pure isotropic pitch and the same isotropic pitch containing 1 wt.% silver were melt spun to form fibers with round and trilobal cross sections. These fibers were then stabilized, carbonized, and activated in carbon dioxide. Field emission scanning electron microscopy (FE SEM), electron dispersive spectra (EDS), and wavelength dispersive spectra (WDS) were used to monitor the size and distribution of the silver particles in the fibers before and after activation. Each of these analyses showed that the distribution of silver particles was extremely uniform before and after activation. The fibers were also weighed before and after activation to determine the percent burn-off. The BET specific surface areas of the activated fibers were determined from N₂ adsorption isotherms measured at −196 °C. The results showed that round and trilobal fibers with equivalent cross-sectional areas yielded similar burn-off values and specific surface areas after activation. Also, activation rates were found to be independent of CO₂ flow rate. The porosity of the activated fibers depended on the total time of activation and the cross-sectional area of fibers. The N₂ adsorption measurements showed that the activated fibers had extremely high specific surface areas (greater than 3000 m²/g) and high degrees of meso- and macro-porosity. FE SEM was also used to investigate surface texture and size of pore openings on the surfaces of the activated fibers. The photos showed that silver particles generated surface macro- and mesopores, in agreement with the inferences from N₂ adsorption measurements.     

Unipolar Fatigue Behavior of BCTZ Lead‐Free Piezoelectric Ceramics

(Ba,Ca)(Ti,Zr)O₃ lead‐free piezoelectric ceramics have been considered to be one of the most potential lead‐free alternatives for PZT in the room‐temperature range. The stability of the piezoelectric performance during unipolar cycling is investigated in this study. It is found that the unipolar fatigue behavior is similar to soft PZT. Developments of bias field, offset polarization, asymmetry in strain, and dielectric hysteresis loops are observed during bipolar measurements. The changes are mainly contributed to the migration of charge carriers to the grain boundaries driven by the unscreened depolarization field. Redistribution of the accumulated charge carriers by bipolar electric cycling or thermal annealing can significantly recover the unipolar fatigued state. The unipolar strain response stabilized after 1000 cycles at 0.053% for an electric field of 0.6 kV/mm (d₃₃*= 883 pm/V), which is a good characteristic for actuator applications.     

Gene Expression Analyses Support Fallopian Tube Epithelium as the Cell of Origin of Epithelial Ovarian Cancer

Folate receptor alpha (FOLR1/FRA) is reported to be overexpressed in epithelial ovarian cancers (EOC), especially the serous histotype. Further, while dysregulation of the folate-dependent 1-carbon cycle has been implicated in tumorogenesis, little is known relative to the potential mechanism of action of FOLR1 expression in these processes. We therefore investigated the expression of FOLR1, other folate receptors, and genes within the 1-carbon cycle in samples of EOC, normal ovary and fallopian tube on a custom TaqMan Low Density Array. Also included on this array were known markers of EOC such as MSLN, MUC16 and HE4. While few differences were observed in the expression profiles of genes in the 1-carbon cycle, genes previously considered to be overexpressed in EOC (e.g., FOLR1, MSLN, MUC16 and HE4) showed significantly increased expression when comparing EOC to normal ovary. However, when the comparator was changed to normal fallopian tube, these differences were abolished, supporting the hypothesis that EOC derives from fallopian fimbriae and, further, that markers previously considered to be upregulated or overexpressed in EOC are most likely not of ovarian origin, but fallopian in derivation. Our findings therefore support the hypothesis that the cell of origin of EOC is tubal epithelium.     

Influence of shear flow on the preparation of polymer layered silicate nanocomposites

In this paper the influence of melt-processing on the final polymer/layered silicate nanocomposite morphology is discussed. In particular the role of shear forces on the transformation of the original large clay agglomerates is of interest. Several polymer nanocomposites were prepared by melt-extrusion, involving polycaprolactone, poly(ethylene oxide), polyamide-12 or polyamide-6 as the matrix polymer. The nanocomposite morphology was characterised by X-ray diffraction and transmission electron microscopy and the clay tactoid morphology with polarised optical microscopy and scanning electron microscopy. The development of the tactoid and nanocomposite morphology during melt-mixing under shear was studied time-resolved by optical microscopy in conjunction with a rheometer and synchrotron X-ray scattering together with a Couette type flow cell. The shear forces in the melt-preparation of polymer layered mineral nanocomposites facilitate the break-up of large-sized agglomerates, whereas the extent of further exfoliation of the mineral layers is determined by the compatibility between the polymer matrix and the mineral layers rather than by shear forces.     

Use of the frequency dependence of the impedance to monitor viscosity during cure

The ability to conveniently and continuously measure the processing properties of polymer resins is important both to the resin supplier and to the fabricator. Frequency dependent electromagnetic sensors (FDEMS) provide an in-situ technique for continuous measurement of the resin's rheological changes both in a laboratory press and in manufacturing tools in an autoclave. In this paper the frequency dependence of ?*(w) is used to quantitatively monitor the viscosity for a tetraglycidyl 4,4′-diaminodiphenyl methane (TGDDM) amine epoxy, to quantitatively monitor the viscosity during processing In a styrene-polyester resin, and to monitor the cure process in an autoclave during cure of a high temperature polyimide-graphite prepreg. In addition, the technique is used to measure the viscosity at various ply positions in a thick TGDDM graphite epoxy laminate during processing in an autoclave.     

Fracture and Subcritical Crack-Growth Behavior of Y-Si-Al-O-N Glasses and Si3N4 Ceramics

Fracture and environmentally assisted subcritical crack-growth processes are examined in bulk Y-Si-Al-O-N oxynitride glasses with compositions typical of the grain boundary phase of silicon nitride ceramics. Both long-crack (in compact tension specimens) as well as short-crack behavior (using indentation techniques) were investigated to establish a reliable fracture toughness and to elucidate the anomalous densification behavior of the oxynitride glass. Environmentally assisted subcritical crack-growth processes were studied in inert, moist, and wet environments under both cyclic and static loading conditions. Behavior is discussed in terms of the interaction of the environment with the crack tip. Likely mechanisms for environmentally assisted crack growth are discussed and related to the subcritical crack-growth behavior of silicon nitride ceramics.