On the realizability of reynolds stress turbulence closures

The realizability of Reynolds stress models in homogeneous turbulence is critically assessed from a theoretical standpoint. It is proven that a well known second-order closure model formulated using the strong realizability constraints of Schumann (1977) and Lumley (1978) is, in fact, not a realizable model. The problem arises from the failure to properly satisfy the necessary positive second time derivative constraint when a principal Reynolds stress vanishes-a flaw that becomes apparent when the nonanalytic terms in the model are made single-valued as required on physical grounds. More importantly, arguments are advanced which suggest that it is impossible to identically satisfy the strong from of realizability in any version of the present generation of second-order closures. On the other hand, models properly formulated to satisfy the weak form of realizability—wherein states of one or two component turbulence are made inaccessible in finite time via the imposition of a positive first derivative condition—are found to be realizable. However, unlike the simpler and more commonly used second-order closures, these models can be ill-behaved near the extreme limits of realizable turbulence due to the way that higher-degree nonlinearities are often unnecessarily introduced to satisfy realizability. Illustrative computations of homogeneous shear flow are presented to demonstrate these points which can have important implications for turbulence modeling.     

Small-signal modeling of HBTs using a hybridoptimization/statistical technique

A new formulation for extracting the elements of the small-signal equivalent-circuit model of heterojunction bipolar transistors (HBTs) is proposed in this paper. This approach avoids the main problem of the conventional extraction methods which, in most cases, is the use of brute-force optimization techniques to extract a large number of parameters. At the beginning, this technique first uses the extraction procedure of a low-frequency HBT model. An analytical formulation that allows the reduction of the number of the unknowns of the low-frequency model to only two, which have to be calculated using a suitable optimization technique, is described. This makes the optimization problem much easier to handle and increases the probability for converging to the actual elements of the model, thus avoiding the converging to spurious solutions. Secondly, in order to extend the model to higher frequencies, a statistical approach is proposed to extract parasitic extrinsic elements. An experimental validation is carried out on three HBT devices and satisfactory results are obtained up to 30 GHz     

Étude des structures planaires en très hautes fréquences par une nouvelle formulation de la méthode des moments dans le domaine spatial

An efficient analytical integration technique for computation of spatial method of moments (MoM) integrals in conjunction with numerical matched loads is presented. The current distribution on the device is solved by using the well-known Galerkin’s MoM procedure applied to mixed potential integral equation in the spatial domain. The scattering parameters are determined by considering infinite lines at each port where only the fundamental mode is assumed to propagate. The contribution of this work is the development of an integration technique for the computation of spatial domain integrals, that is fast and rigorous. This technique is based on a Taylor series expansion of the integrands involving only polynomial functions. The use of polynomial forms in the integrals leads an immediate analytical integration, and the computation time will be considerably reduced.     

Reduction electrochimique des cetones insaturees—VII. Influence de l'acidite du milieu sur le comportement cathodique des cetosulfones

The ketosulfones are known to be reduced electrochemically, in weakly acidic medium with scission of the CS bond. Nevertheless, in strongly acidic media, the electroactive entity being the protonated form of the carbonyl group, the reaction may lead to pinacols. In the case of γ-ketosulfones, the electroreduction in very weakly protic media is followed by the loss of proton of the acidic substrate due to the effect of electrogenerated bases. This chemical cleavage of the CS bond yields to α-ethylenic ketones reducible at the electrolysis potentiel. On the other hand, for the long chained ketosulfones the reduction may occur through a partial intramolecular electron transfer.     

Cathodic behaviour of p-toluenesulfonamides in organic solvents

Cathodic reduction of several secondary and tertiary p-toluenesulfonamides and gem-N-disulfonamides were investigated by cyclic voltammetry and controlled potential electrolysis at mercury electrode in aprotic and protic dmf. In the cleavage of tertiary p-toluenesulfonamides two Faradays per mole were consummed, resulting in the formation of amine and the sulfinate ion. In the case of secondary p-toluenesulfonamides, electrochemically inactive sulfonamide anions were formed at the electrode surface by acid–base reaction between acidic substrate and electrogenerated bases. Sulfonamides anions were obtained also in the solution bulk with adding strong base and by cathodic cleavage of gem-N-disulfonamides in aprotic media. General reduction mechanisms are postulated and structure effects on the scope of the reduction are discussed for more complex sulfonamides.     

Interference analysis for asynchrounous OFDM/FBMC based cognitive radio networks over Rayleigh fading channel

In the future fifth generation networked society, devices will suffer from the asynchronous multi-carrier effect which impacts the user’s quality of experience. This paper investigates the timing misalignment effect on interference level in the context of a cognitive radio (CR) network. Our study considers both multicarrier techniques orthogonal frequency division multiplexing (OFDM) and filter bank multicarrier (FBMC). The originality of our paper consists in proposing a simple but accurate analytical model to evaluate our system’s performance in terms of interference level, signal-to-interference-plus-noise ratio and bit error rate. Specifically, two case studies are considered, a single-user case (one primary user and one secondary user) and a multi-user case with exact theoretical expressions of interference level. We had also made a comparison between OFDM and FBMC techniques. The most striking observation to emerge from our results is that the asynchronous interference is inversely propositional to timing offset even for the multi-user case, and that differences in the normalized interference level between the single/multi-user cases is barely perceived for the FBMC technique, proving its efficiency. Our simulations’ results had further strengthened our confidence in the suggested model. It shows that FBMC is best suited for CR networks since it provides BER improvements compared to OFDM.

     

Misalignment controller in wireless battery charger for electric vehicle based on MPPT method and metaheuristic algorithm

This paper focuses on applying a wireless power transfer WPT technology in an electric vehicle battery charger. The wireless charger system is based on the principle of resonance inductive coupling power through a coreless transformer. The WPT system is considered as a multi parameter and multi constrained nonlinear system. The main contribution in this paper is the use of PSO and GA metaheuristic algorithms in the optimization of a transformer design regarding the impact of a lateral misalignment and the separation distance between the primary and secondary coils. To find the best global solution which is considered as the maximum efficiency in the complex system, both algorithms are compared. A perturbation-and-observation-based tracking system is developed through an efficiency sensing system to act on the misalignment issue and the car position. An additional PSO controller is performed to control the duty cycle of the boost converter in order to follows the maximum efficiency operating points of a WPT system. The discrepancy is the use of the resonant inductive coupling as a source of the MPPT so as to perturb the car position and observe the transferred. Furthermore, the modeling of a contactless transformer is optimized using metaheuristic algorithm.     

A Novel Adaptive and Cooperative Scheme to Save Energy for Wireless Sensor Network

In this paper, we evaluate the performance of a novel cooperative adaptive relaying scheme called ISDF (Incremental Selective Decode and Forward). We compare the energy efficiency of this underlying scheme with direct transmission (DT), Fixed and adaptive relaying schemes in Wireless Sensor Network (WSN). The system is constrained by a minimum value of Signal-to- Noise Ratio (SNR) and the end-to-end throughput. We consider a three-node cooperative system. The relay is equidistant to the source and destination, and then we study different positions of the latter. The destination receives two copies of the message: one from the source and the other from the relay. Then it combines them by using maximal ratio combining (MRC). The proposed scheme differs from other schemes by the combination of the selective decode and forward scheme with the incremental scheme which requires the presence of a feed-back from the destination. The analysis reveals that the proposed ISDF provides good energy efficiency compared to DT and other cooperative schemes. It also shows that DF cooperative scheme (decode and forward , either with feedback or no, is outperformed by AF (amplify and forward) scheme especially when the relay is placed near the destination.

     

Metric anticipation to manage mobility in mobile mesh and ad hoc wireless networks

In mobile ad hoc networks (MANETs), node mobility management is performed by the routing protocol. It may use metrics to reflect link state/quality. But, the delay between measures of the link quality and its integration in the route computation is very detrimental to the mobility management. Consequently, routing protocols may use lossy links for a few seconds leading to a significant performance deterioration. In this paper, we propose a new routing metric technique calculation which aims at anticipating link quality. Basically, the idea is to predict metric values a few seconds in advance, in order to compensate the delay involved by the link quality measurement and their dissemination by the routing protocol. Our technique is based on measurements of signal strength and is integrated in two classical routing metrics: ETX (expected transmission count) and ETT (expected transmission time). Validations are performed through both simulations and a testbed experimentation with OLSR as routing protocol. NS-3 simulations show that our metric may lead to a perfect mobility management with a packet delivery ratio of 100%. Experiments on a testbed prove the feasibility of our approach and show that this technique reduces the packet error rate by a factor of 3 in an indoor environment compared to the classical metrics calculation.     

Parameterisation of the MRP method: automatic identification and extraction of properties

The overall context of this paper is the parameterisation of the material requirement planning method. It is crucial to be able to evaluate the potential effects of the parameters on the production system’s performance indicators (PI). This evaluation is generally the result of the combination of an experimental design with a production system simulator. This paper proposes an approach facilitating the interpretation of the effects of the experimental design method. The specific feature of our approach is that it proposes the classification of the effects as a model for the automatic identification and extraction of the properties. These characterise the relations between the parameters and the PI.