Habitat-specific Signal Structure for Olfaction: An Example from Artificial Streams

Many animals use chemical signals to acquire information about their habitats. The structure of this information is dependent upon specific features within a habitat, and the information in signals can be habitat-specific. We quantified the spatial and temporal information in an aquatic odor plume in three different artificial stream habitats with different substrate types by measuring turbulent odor plumes with an electrochemical detection system. Streams had one of three substrate types that correlated with typical aquatic habitats: sand (4.2 × 10^–2 cm diameter), gravel (2.5 cm), and cobble (4.5 cm). As predicted from the hydrodynamics, the spatial and temporal structures of the signals were different on different substrates. Spectral analysis showed that the sand and cobble substrates had signals that were dominated by lower frequency fluctuations, whereas gravel had the highest and broadest range of signal fluctuations. Cross- and autocorrelations showed that signals on the gravel substrate had the largest spatial and shortest temporal components. Our results imply that the information obtained from chemical signals may be limited in some habitats. These constraints on information may affect how organisms perform chemically mediated behaviors.     

Hydrotropic and surfactant properties of novel diisopropyl naphthalene sulfonates

A novel surfactant and hydrotrope, sodium diisopropylnaphthalene sulfonate (SDIPNS) has been developed. It contains about 92% diisopropylnaphthalene sulfonate, compared to other materials which are less than 50% diisopropylnaphthalene sulfonate. Aqueous solutions of 34–36% active SDIPNS have dual functionality. They have excellent surface properties and are compatible with conventional anionic, nonionic, and amphoteric surfactants. They demonstrate good laundering detergency in combination with sodium lauryl ethoxy sulfate, with or without builder. They maintain surface activity in 150 ppm hard water (Ca²⁺/Mg²⁺=2∶1), 5% NaCl, pH 2, and pH 12. They are effective hydrotropes. They enhance surfactant solubility, raise the cloud point of nonionic surfactants, and modify the viscosity of surfactant formulations. They are light in color and are low-foaming. Presented as a Poster Session at the American Oil Chemists' Society Annual Meeting, May 9–12, 1999, Orlando, Florida.     

Adsorption mode of ethyl pyruvate on platinum: an in situ XANES study

The adsorption of ethyl pyruvate on Pt(111) has been studied by in situ XANES measurements in the presence and absence of hydrogen. Depending on the hydrogen and ethyl pyruvate pressure, the C and O K‐edge spectra exhibit distinctly different angular dependence. Without hydrogen ethyl pyruvate is oriented preferentially perpendicular to the surface, indicating bonding via the O lone pairs. In the presence of hydrogen the mean orientation is more tilted towards the surface. Likely, ethyl pyruvate also interacts with Pt via its π system under these conditions. The observed angle‐dependent shift of the energy of the π* and σ* resonances indicates the coexistence of differently adsorbed ethyl pyruvate species. The experimental findings demonstrate the importance of the in situ approach for unraveling the adsorption mode of ethyl pyruvate in the enantioselective hydrogenation over cinchona‐alkaloid‐modified Pt. This revised version was published online in July 2006 with corrections to the Cover Date.     

Development of a novel test system for in situ catalytic, electrocatalytic and electrochemical studies of internal fuel reforming in solid oxide fuel cells

A test system based around a thin‐walled extruded solid electrolyte tubular reactor has been developed, which enables the fuel reforming catalysis and surface chemistry occurring within solid oxide fuel cells and the electrochemical performance of the fuel cell to be studied under genuine operating conditions. It permits simultaneous monitoring of the catalytic chemistry and the cell performance, allowing direct correlation between the fuel cell performance and the reforming characteristics of the anode, as well as enabling the influence of drawing current on the catalysis and surface reaction pathways to be studied. Temperature‐programmed reaction measurements can be carried out on anodes in an actual SOFC, and have been used to investigate the reduction characteristics of different anode formulations, methane activation and methane steam reforming, and to evaluate the nature and level of carbon deposition on the anode during reforming. This revised version was published online in July 2006 with corrections to the Cover Date.     

Influence of Fluorine Content in Apatite–Mullite Glass-Ceramics

The nucleation and crystallization of a series of glasses based on 4.5SiO₂·3Al₂O₃·1.5P₂O₅·(5 − z )CaO · z CaF₂ with a Ca:P ratio corresponding to apatite were studied. In these glasses, the objective was to investigate the influence of fluorine content and z was varied from 3 to 0. All the glasses studied crystallized to fluorapatite (FAP) and mullite with the exception of the glass containing no fluorine, which crystallized to β-tricalcium phosphate (Ca₃(PO₄)₂) and anorthite (CaAl₂Si₂O₈). Glasses that contained sufficient fluorine to form FAP bulk nucleated to give FAP without a nucleation hold. Thermal gravimetric analysis demonstrated a significant weight loss corresponding to the crystallization of mullite, which increased with the fluorine content of the glass and also with decreased particle size. The loss was attributed to volatile SiF₄. The glass transition temperature decreased with increased fluorine content of the glass.     

Influence of Processing Parameters on the Sintering and Electrical Properties of Pb(Zn1/3Nb2/3)O3-Based Ceramics

Pb(Zn_1/3Nb_2/3)O₃-based ceramics have been prepared by two different processing methods: conventional (PZN-C) and reaction-sintering (PZN-RS). The conventionally prepared PZN-based ceramics densified at lower temperatures (950°C) than the reaction-sintered samples (1100°C), but the perovskite/pyrochlore ratio was always higher in PZN-RS. The presence of a substantial amount of pyrochlore phase in PZN-C ceramics caused a decrease in the electrical properties. The maximum dielectric constant values in PZN-C ceramics were 10%–15% lower than those of PZN-RS, despite a similar average grain size, 7 ± 0.2 μm. The temperature of the maximum of the dielectric constant ( T _max) was lower than that expected from the mixing rule because of the possible formation of Ba–Nb clusters. The higher chemical homogeneity in PZN-RS ceramics is the main reason for the higher dielectric constant, T _max and electromechanical response, as well as for the lower difference between T _max and the depolarization temperature ( T _d) and the lower diffusiveness parameter (δ).     

Submarine mine tailings management

The placement of mine tailings at depth in the marine environment is reviewed. This review considers first the engineering aspects of a pipeline system which transports tailings slurry from a process plant to the coast and then to a location at a depth of typically 200 m on the continental slope. Next, the fluid dynamic behaviour of the tailings, once discharged from the end of the pipe, are discussed, and a numerical model is presented which simulates the fate of both the dissolved and solids component of the tailings slurry in the marine environment. This latter model can be used to estimate the environmental impact of a proposed deep sea tailings placement system.     

Effect of combining boron nitride with fluoroelastomer on the melt fracture of HDPE in extrusion blow molding

Boron nitride (BN) is a new polymer processing aid which not only eliminates surface melt fracture in the extrusion of molten polymers, but also postpones the critical shear rate for the onset of gross melt fracture to significantly higher values that depend on resin type and additive concentration. In this work, the influence of BN as a polymer processing additive is first examined in the extrusion blow molding of high‐density polyethylene (HDPE) resins in order to evaluate its usefulness and performance in operations other than continuous extrusion. The equipment used includes both a Battenfeld/Fisher 50‐mm extrusion blow molding machine and a parallel‐plate rheometer. Two types of HDPE, which are blended with boron nitride at various concentration levels, are tested accordingly. It is found that the degree of BN dispersion, characteristics of the HDPE resins, extrusion temperature, and induction time play an important role in eliminating melt fracture. Finally, the influence of combining BN with fluoroelastomer, as an enhanced and potentially better processing aid on the melt fracture of a third HDPE is examined. It is found that such a combination is a superior processing aid that allows extrusion blow molding at very high shear rates.     

An effect of iron(III) oxides crystallinity on their catalytic efficiency and applicability in phenol degradation—A competition between homogeneous and heterogeneous catalysis

Catalytic efficiency, stability and environmental applicability of five iron(III) oxide nanopowders differing in surface area and crystallinity were tested in degradation of concentrated phenolic aqueous solutions (100 g/L) at mild temperature (30 °C), initially almost neutral pH and equimolar ratio of hydrogen peroxide and phenol. The catalyst properties were easily controlled by varying in reaction time during isothermal treatment of ferrous oxalate dihydrate in air at 175 °C. Although the catalytic efficiency clearly increases with the surface area of the nanopowders, it is not due to the solely heterogeneous catalytic mechanism as would be expected. The amorphous Fe₂O₃ nanopowders possessing the largest surface areas (401 m² g⁻¹, 386 m² g⁻¹) are the most efficient catalysts evidently due to their highest susceptibility to leaching in acidic environment arising as a consequence of phenol degradation products. Thus, these amorphous samples act partially as homogeneous catalysts, which was confirmed by a high concentration of leached Fe(III) ions in the solution (19 ppm). The crystalline hematite (α-Fe₂O₃) samples, varying in surface area between 337 m² g⁻¹ and 245 m² g⁻¹, are generally less efficient when compared to the amorphous powders, however their catalytic action is almost exclusively heterogeneous as only 3 ppm of leached Fe(III) was found in the reaction systems catalyzed by nanohematite samples. A significant difference in relative contributions of heterogeneous and homogenous catalysis was definitely established in buffered reaction systems catalyzed by amorphous Fe₂O₃ and nanocrystalline hematite. The nanohematite sample exhibiting the highest heterogeneous action was tested at decreased initial phenol concentration (10 g/L), which is closer to the real contents of phenol in waste waters, and at different hydrogen peroxide/phenol molar ratios to consider its environmental applicability. At the hydrogen peroxide/phenol ratio equal to 5, no traces of the leached iron were detected and the phenol conversion of 84% was reached. Moreover, such a high degree of conversion is accompanied by a decrease of the chemical oxygen demand (COD) from the initial value of 11.23 g/L to 4.22 g/L after 125 min. This fact indicates that the considerable fraction of primary reaction products was totally degraded.     

Effects of microwave radiation on electrodeposition processes at tin-doped indium oxide (ITO) electrodes

In situ microwave activation is investigated for the electrodeposition of a metal (gold) and for a metal oxide (hydrous Ti(IV) oxide) onto tin-doped indium oxide (ITO) film electrodes. It is demonstrated that localized microwave heating of the ITO film can be exploited to affect electrodeposition processes.The electrochemically reversible and temperature sensitive one-electron redox system Fe(CN)₆^3−/4− was employed in aqueous solution in order to calibrate the average surface temperature at the ITO film electrode. In the presence of microwave radiation the average electrode surface temperature reached ca. 363 K whereas under the same conditions the bulk solution temperature reached ca. 313 K. Therefore localized heating of the ITO film appears to be important.The rate of electrodeposition of gold from an aqueous 1 mM tetrachloroaurate(III) solution in 0.1 M KCl (adjusted to pH 2) is enhanced by microwave activation. However, the morphology of deposits remains un-effected. Hydrous titanium (IV) oxide films were electrodeposited from an aqueous solution of 1 mM TiCl₃ in 0.1 M acetate buffer pH 4.7. Dense films with blocking character were obtained with conventional heating but a fibrous more open deposit forms in the presence of microwaves.