Performance of Green Solvents in the Extraction of Sunflower Oil from Enzyme-Treated Collets

The main goal of this work is to evaluate the extraction of sunflower oil from enzyme-treated collets using ethanol and isopropanol (IPA) as solvents. The sunflower collets are pretreated with the multienzyme complex Viscozyme L prior to solvent extraction by the Soxhlet method. The influence of the moisture content of the collets, pretreatment, processing time, and solvent type on the amount of total extracted material and the oil extraction efficiency is studied. Some quality parameters such as phospholipid content of the oil and chlorogenic acid content of the residual meal are also analyzed. At low moisture content (7%) the solvents exhibit similar oil extraction ability (98–99%), but with increasing moisture the extraction efficiency of ethanol decreases to about 85%, while no significant differences are observed for IPA. The enzymatic treatment increases the extraction efficiency for all times, especially for ethanol. It is observed that IPA is more efficient in the extraction compared to ethanol, and the amount of nonlipid material is reduced by ≈70%. In addition, the oil extracted with IPA have lower phospholipid content and the residual meal presents a higher chlorogenic acid content. Practical Applications:This work would contribute toward the use of green solvents in the extraction of sunflower oil from collets. Ethanol and isopropanol, used as solvents, present attractive advantages, including low toxicity, good operational security, as well as being obtained from a renewable source. The obtained data provide up-to-date information on the use of these alcohols in the extraction of sunflower oil from collets and the influence of operating conditions, such as moisture content, enzymatic pretreatment of the collets, and the extraction time. Information about oil and meal quality is also reported.     

CYP154C5 Regioselectivity in Steroid Hydroxylation Explored by Substrate Modifications and Protein Engineering**

CYP154C5 from Nocardia farcinica is a P450 monooxygenase able to hydroxylate a range of steroids with high regio- and stereoselectivity at the 16α-position. Using protein engineering and substrate modifications based on the crystal structure of CYP154C5, an altered regioselectivity of the enzyme in steroid hydroxylation had been achieved. Thus, conversion of progesterone by mutant CYP154C5 F92A resulted in formation of the corresponding 21-hydroxylated product 11-deoxycorticosterone in addition to 16α-hydroxylation. Using MD simulation, this altered regioselectivity appeared to result from an alternative binding mode of the steroid in the active site of mutant F92A. MD simulation further suggested that the entrance of water to the active site caused higher uncoupling in this mutant. Moreover, exclusive 15α-hydroxylation was observed for wild-type CYP154C5 in the conversion of 5α-androstan-3-one, lacking an oxy-functional group at C17. Overall, our data give valuable insight into the structure–function relationship of this cytochrome P450 monooxygenase for steroid hydroxylation.     

Effect of Aluminum Content on the Dynamic Recrystallization of Fe18MnxAl0.74C Steels During Hot-Forging Treatments

Metallurgical and Materials Transactions A - In the present work, the dynamic recrystallization and microstructural evolution of the family of advanced high-strength steels Fe18MnxAl0.74C are...     

Synthesis of titanium aluminide coatings on aluminum and titanium surfaces by mechanical alloying and subsequent annealing

Intermetallic Ti-Al-based coatings were synthesized by mechanical alloying in a vibratory ball mill and subsequent annealing. A titanium layer was deposited on aluminum specimens and an aluminum layer and aluminum-titanium mixture were deposited on titanium specimens. Under the effect of milling balls, powder particles deposit at the substrates, forming layers that have a very good cohesion with the substrate. During subsequent heating, diffusion layers on the basis of titanium-aluminum phases are synthesized as a result of the chemical interaction between titanium and aluminum. In the case of titanium layer deposited on aluminum, the temperature interval of transformations is 600–650°C; first, a Ti₃Al₅-based phase is formed; then, as diffusion saturation with Al increases, an Al₂Ti-based layer appears; and finally, the Al₃Ti compound is formed. The reaction rates depend on the temperature and the duration of annealing. On titanium with a (Ti + Al) layer deposited on its surface, the Al₃Ti, Al₂Ti, TiAl, and Ti₃Al compounds are formed in a temperature interval of 600–900°C. In the case of deposition a homogeneous aluminum layer on titanium, only Al₃Ti and Ti₃Al phases were observed after annealing.     

Monitoring the tensile deformation in real unidirectional Kevlar-epoxy composites

Two acoustic emission (AE) parameters, event count rate (ER) and the skewness of the peak amplitude distribution (PAD), were found to correlate with mechanical and damage mechanisms in unidirectional Kevlar-epoxy composites loaded in tension. The ER of the AE reached a local maximum at about 0.3σ_cu (σ_cu= composite tensile strength), a minimum at about 0.6–0.7σ_cu, and increasing ER rates were noted as failure stress approached, with a peak at final failure.Along with our proposed approach to evaluate the PAD as a tool for characterizing processes, damage mechanisms and failure modes, the third statistical moment of the PAD, the skewness, was found to be able to distinguish between various mechanisms. From the beginning of loading until completion of the fibre straightening process, 0.6–0.7σ_cu, the value of the skewness steadily decreased, and then gradually increased to final failure. This behaviour is explained by a model based on the non-elastic mechanisms which contribute to the monitored AE. At final failure, the PAD's skewness value was affected by macroscopic failure modes. When this mode comprises fibre fracture with little matrix and interface splitting, the skewness decreased; when fibre failure was accompanied by matrix and interface splitting, its value changed slightly or even increased.     

Synthesis and crosslinking properties of phenolphtalein dimethacrylate

Summary By reacting esterification of phenolphtalein with methacrylate chloride, phenolphtalein dimethacrylate was obtained. Based on the results of elemental analysis, FTIR, ¹H-NMR and ¹³C-NMR spectra, the structure of the product was proposed. The dimethacrylate was used as new crosslinker to crosslink poly(methyl methacrylate) (PMMA). The influence of the amount dimethacrylate on the crosslink density and some properties of the crosslinked polymers networks such as swelling, mechanical properties (tensile strength and elongation at break) and thermal stability were examined.     

Numerical characterization and experimental verification of an in-plane MEMS-actuator with thin-film aluminum heater

In this paper, a novel concept of a thermo-mechanical MEMS actuator using aluminum thin-film heaters on a thermal oxide for electrical insulation is presented. The actuator is part of an universal tensile testing platform for thermo-mechanical material characterization of one dimensional materials on a micro- and nano-scopic scale under different environmental conditions, as varying temperatures, pressure, moisture or even vacuum and is realised in BDRIE technology. It is shown, that the actuator concept fulfills the requirements for the use in a tensile loading stage along with heterogeneously integrated nanofunctional elements, following a specimen centered approach in line with bottom-up self-assembly processes. Simulation and experiment agree very well in the thermal and mechanical domain and allow subsequent optimisation of the actuator performance.     

Catalyzing the curing reaction of a new benzoxazine-based phenolic resin

The effect of potential catalysts on the curing reaction of a new type of phenolic resins obtained from benzoxazine precursors is studied. These novel resins solve the shortcomings of traditional phenolics because they cure by a ring-opening mechanism that avoids the release of volatiles. Isothermal and nonisothermal differential scanning calorimetry (DSC) data is used to determine the influence of the catalysts on the curing kinetics. Fourier transform infrared (FTIR) spectroscopy is also applied. The benzoxazine chosen for this study is a purified benzoxazine monomer based on bisphenol-A, formaldehyde, and aniline. The as-synthesized benzoxazine precursor is also studied to determine the influence of the dimers and higher oligomers in the curing mechanism. The presence of these structures seems to catalyze the curing reactions. The activation energy and overall reaction order of the as-synthesized precursor are determined. Among the catalysts tested, adipic acid shows the most promising results. For all the cases studied the curing reaction is autocatalyzed up to a diffusion-controlled stage. © 1995 John Wiley & Sons, Inc.     

Selective oxidation of ammonia to nitrogen on transition metal containing mixed metal oxides

The selective catalytic oxidation of ammonia to nitrogen (NH₃-SCO) has been studied over hydrotalcite derived mixed metal oxides containing Cu, Co, Fe or Ni. XRD, BET, NH₃-TPD and TPR techniques were used for catalysts characterization. Results of NH₃-SCO were compared with those of selective catalytic reduction of NO with NH₃ (NO-SCR). Reaction mechanism was studied by temperature-programmed surface reaction (TPSR) and activity tests with a various contact time. Catalytic performance of the studied samples depends on both kind and loading of transition metals in the mixed metal oxide system. The Cu-containing samples have been found to be the most active catalysts of the NH₃-SCO process. Transition metal loading strongly influences distribution of ammonia oxidation products. The highest selectivity to N₂ was measured for the catalysts with the lowest transition metal content.     

Simple method for estimation of volatile carbonyl compounds in edible oils and fried potato chips

A simple and sensitive method has been devised to determine the amounts of volatile carbonyl compounds in vegetable oils and fried potato chips, using a chemical reaction trap and absorption spectrophotometry. A sample of oil or fried potato chips is heated and simultaneously purged with a flow of nitrogen gas which further bubbles through a tube (trap) containing a hydroxylamine hydrochloride solution. The volatile carbonyl compounds are removed from the sample with the purge gas and retained in the trapping solution as they react to form the less volatile oxime derivatives. These are subsequently estimated by ultraviolet absorption, at wavelength 212 nm for the total oximes and at 272 nm specifically for conjugated diene carbonyl oximes, including furfural if present. Volatile carbonyls can be determined by this method at levels as low as 0.1–0.5 ppm of the sample. The method has been applied to the analysis of samples of canola (low erucic acid rapeseed) oil, cottonseed oil, and potato chips, all before and after storage. The method should be suitable also for other types of fried food.