非化学计量LaNi5型储氢合金的性能

采用富La混合稀土与Ni、Co、Mg等元素组合，获得了一种非化学计量LaNi5型储氢合金、用金相、XRD和SEM-EDX等方法分析了该合金的组织结构，研究了合金的气相储氢特性以及电化学性能，结果表明：在1.6MPa氢压和温度29℃下，该合金的储氢量达到1.58%（质量分数），该合金的放电容量为380mAh/g。经300次循环后容量保持率为55%，该合金的基体是CaCu5型结构的LaNi5相，但有第二相（LaMg)Ni3析出，这种第二相的形成是导致该合金大容量的关键。     

In—situ Composite Based on Poly （ethylene terephthalate）,Polyamide and Polyethylene with Microfibres Formed through Extrusion and Hot Stretching

In-situ composites based on dispersed poly (ethylene terephthalate) (PET) or polyamide (PA),and continuous Polyethylene (PE) were prepared through a single screw extruder of Haake rheometer system with a rod-die relatively small in diameter.The extrudate was drawn at a drawing ratio of 3.1,and then quickly cooled in cold water.The specimens were obtained by injection molding at processing temperatures less than 190℃，far below the melting temperature of PET (265℃) and PA (230℃),which can maintain the solid state of PET and PA microfiber phase in the composites.Morphological observation with scanning electron microscopy (SEM) indicated that PET and PA can more or less form in-situ microfibers at compositions studied (0-20 wt pct PET or PA),and especially,PET and PA were almost deformed into fibers at the concentration of 15wt pct.Eensile strength and especially.PET and PA were almost deformed into fibers at the concentration of 15wt pct.Tensile strength and modulus of the blends reinforced by PET or PA microfibers showed to be increased from the tensile test results.The most noticeable improvement of the tensile properties occurred at 15wt pct of PET in PET/PE system,corresponding to the highest microfiber content,where the tensile strength reached 32.5 MPa,whereas only 19.5 MPa for the pure PE.     

明渠湍流床面附近跃移层面颗粒浓度垂线分布

本文以动理学理论的Boltzmann方程为基础，考虑明渠湍流床面附近猝发喷射和清扫运动对跃移层内运动颗粒的不同作用，分析了明渠中泥沙颗粒浓度垂线分布问题，得到了适用于包括跃移层、悬移层在内的统一浓度垂线分布公式。文中着重研究了跃移层内运动颗粒的浓度垂线分布，并将本文结果与实测跃移层内浓度垂线分布及实测跃移层顶部浓度进行了对比，结果表明理论与实验两者符合较好。     

一种改进的同步侦破和识别过失误差的方法

将线性组合技术引入过失误差同步估计法 ,用于确定候选过失误差子集。以一个循环网为例 ,对两种算法的性能进行了比较。对一个蒸汽系统的稳态数据校正仿真结果证明了该方法的有效性     

EMD与KOH溶液的相互影响

利用滴定分析、热失重分析以及XRD方法研究了EMD和KOH溶液混合后的变化。结果表明:碱与MnO2可以相互作用并导致体系温度的升高,碱浓度的下降,EMD中形成Mn3O4以及MnO2中结合水的损失。相互作用的结果与所加KOH溶液的浓度、EMD中的水含量、二者用量的比例关系以及体系的温度有关。     

载人航天高可靠伺服技术

回顾了载人航天高可靠伺服技术的研制道路，介绍了用于载人航天火箭推力矢量控制中的新型三余度伺服机构的技术特点，对载人航天伺服技术的未来发展进行了分析和展望。     

应用底饲回燃循环流化床技术改造东锅DG35/3.82-7型流化床锅炉

采用飞灰循环底饲回燃技术改造西南合成制药总厂热电分厂、天府矿务局磨心坡发电厂2台东方DG35/3.82-7型低倍率循环流化床锅炉。改造后运行结果表明,锅炉可长期、稳定运行,尾部飞灰可燃物含量大幅度降低,锅炉蒸发量提高20％左右,节煤效果明显。为燃用贫煤、无烟煤和煤矸石等劣质燃料且锅炉炉膛高度较低的电站技改,提供了一种切实可行的方法。     

Mode coupling and equilibrium mode distribution conditions in plastic optical fibers

The equilibrium mode distribution (EMD) condition is critical for optical fiber measurements. In this letter, we examine the achievement of EMD condition inside plastic optical fibers (POF's) under different launch conditions. Our pulse broadening measurements of step-index (SI) POF's as a function of fiber length show that the EMD condition can readily be achieved in an SI POF much shorter than in glass optical fibers. The observation of the EMD condition was also independently verified using the far-field pattern technique.     

转移法色交换

将图Ｇ的着色由一种变为中一种，通常用Ｋｅｍｐｅ法以交换。但是，对于某些情况，用此法无效。针对这个问题，本文提出了一种转移法色交换，它适用于平面图着色，方法直观，清晰且有效。     

不清根手工双面焊材料及工艺研究

本文分析了中厚板传统手工双面焊存在的诸如打底焊焊缝质量无法保证，需用碳弧气刨清根；工人劳动强度大；生产效率低；焊接质量不稳定等主要问题。为提高打底焊焊道质量，不用清根使背面得到良好的凹成形，研制了适合Ｘ形坡口的梯形体陶瓷衬垫。探讨了焊缝背面成形的主要影响因素及控制方法。