Cost-Efficient SHA Hardware Accelerators

This paper presents a new set of techniques for hardware implementations of Secure Hash Algorithm (SHA) hash functions. These techniques consist mostly in operation rescheduling and hardware reutilization, therefore, significantly decreasing the critical path and required area. Throughputs from 1.3 Gbit/s to 1.8 Gbit/s were obtained for the SHA implementations on a Xilinx VIRTEX II Pro. Compared to commercial cores and previously published research, these figures correspond to an improvement in throughput/slice in the range of 29% to 59% for SHA-1 and 54% to 100% for SHA-2. Experimental results on hybrid hardware/software implementations of the SHA cores, have shown speedups up to 150 times for the proposed cores, compared to pure software implementations.      

AlGaN-based quantum-well heterostructures for deep ultraviolet light-emitting diodes grown by submonolayer discrete plasma-assisted molecular-beam epitaxy

Features of plasma-assisted molecular-beam epitaxy of AlGaN compounds at relatively low temperatures of the substrate (no higher than 740°C) and various stoichiometric conditions for growth of the nitrogen- and metal-enriched layers are studied. Discrete submonolayer epitaxy for formation of quantum wells and n-type blocking layers without varying the fluxes of components was used for the first time in the case of molecular- beam epitaxy with plasma activation of nitrogen for the nanostructures with the Al _x Ga_{1 ? x} N/Al _y Ga_{1 ? y} N quantum wells. Structural and optical properties of the Al _x Ga_{1 ? x} N layers in the entire range of compositions (x = 0–1) and nanostructures based on these layers are studied; these studies indicate that there is photoluminescence at room temperature with minimum wavelength of 230 nm. Based on the analysis of the photoluminescence spectra for bulk layers and nanoheterostructures and their temperature dependences, it is concluded that there are localized states in quantum wells. Using the metal-enriched layers grown on the c-Al₂O₃ substrates, heterostructures for light-emitting diodes with Al _x Ga_{1 ? x} N/Al _y Ga_{1 ? y} N quantum wells (x = 0.4–0.5, y = x + 0.15) were obtained and demonstrated electroluminescence in the ultraviolet region of the spectrum at the wavelength of 320 nm.     

Photo-Fenton removal of water-soluble polymers

This paper presents the results of experiments carried out in a laboratory-scale photochemical reactor on the photodegradation of different polymers in aqueous solutions by the photo-Fenton process. Solutions of three polymers, polyethyleneglicol (PEG), polyacrylamide (PAM), and polyvinylpyrrolidone (PVP), were tested under different conditions. The reaction progress was evaluated by sampling and analyzing the total organic carbon concentration in solution (TOC) along the reaction time. The behavior of the different polymers is discussed, based on the evolution of the TOC–time curves. Under specific reaction conditions, the formation and coalescence of solid particles was visually observed. Solids formation occurred simultaneously to a sharp decrease in the TOC of the liquid phase. This may be favorable for the treatment of industrial wastewater containing polymers, since the photodegradation process can be coupled with solid separation systems, which may reduce the treatment cost.     

Swift and Selective Reduction of Nitroaromatics to Aromatic Amines with Ni–Boride–Silica Catalysts System at Low Temperature

Various nitroaromatics are successfully reduced to amines with 100% conversion and selectivity in methanol at low temperature (≈5 °C), by using versatile system of 5% Ni–SiO₂ catalyst and NaBH₄ and in situ generation of Ni boride. The catalytic efficiency of Ni loading (5%, 10% and 15%) with silica or titania as support materials is investigated for reduction of nitrobenzene. The Ni–titania/NaBH₄ system recorded lower conversion and selectivity. The IR studies indicate that silica support does not have free –OH group on its surface. Thus the nickel boride is anchored to the silica to facilitate the catalytic process.     

Distributed Transmit Antenna Selection (DTAS) Under Performance or Energy Consumption Constraints

Motivated by the transmit antenna selection (TAS) concept, used in Multiple-Input-Multiple-Output systems, we argue for distributed transmit antenna selection (DTAS), which corresponds to a method of selecting a subset of available relays in cooperative diversity systems. Assuming amplify and forward relays, the proposed selection method represents a low-complexity tool for determining the optimum relaying set. Two optimization problems are studied: the error probability minimization subject to total energy consumption constraints, and the dual one, the total energy consumption minimization under error performance constraints. Numerical examples verify the advantage of the proposed method in adapting the number of relaying terminals to the desired performance-consumption tradeoff.     

Kriterien für die Zulassung von Tierarzneimitteln gegen Zeckenbefall bei Hunden und Katzen: Ein Überblick der aktuellen Anforderungen und Möglichkeiten unter Berücksichtigung der derzeitig gültigen Leitlinien

Ohne Zusammenfassung The online version of the original article can be found under doi:.     

Investigation into Polarization of Unloaded and Loaded Microstrip Square-Ring Antennas

The polarization characteristic of unloaded and loaded square-ring microstrip antennas is investigated. Several different loading types like single-stub, dual-stub, notch, gap and shorting-pin are considered and their effects are studied. Loading enables feeding using a 50-Omega probe. The simulation and measurement results show that the loading techniques excite a loaded TMy ₁₁ mode that is orthogonal to the unloaded TMx ₁₁ mode. This indicates that by loading the ring antenna its polarization can be switched adaptively. However, the purity of the loaded and unloaded modes depends on the loading type. For some loading types like gap and shorting-pin, the excitation of the unloaded mode seems negligible, in comparison to the loadings by stub and notch. For the stub and notch loaded antennas the unloaded mode is also present, and its excitation efficiency is frequency dependent. Thus, their polarization plane, which is due to both loaded TMy ₁₁ and unloaded TMx ₁₁ modes, also becomes frequency dependant. The results of this investigation can be useful in selecting the loading methods for high-impedance microstrip ring antennas, and control of their impedance and polarization. The knowledge of the antenna polarization is essential in communications, and its dependence on the loading type can be used as an important parameter in design of adaptive antennas and sensors.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Smart phones and interactive reports leave traffic in the rearview mirror

To convey the dynamic information related to traffic conditions in various parts of a city, we propose an environment utilizing the technology of smart phones to provide information anywhere and anytime. Called ";The Interactive Traffic Beat Project,"; it uses a Web-based service to deliver this information to people through their cell phones at the right time so that valuable time can be saved and the chaos on the roads can be managed.     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.