Soret and Dufour effects between two rectangular plane walls with heat source/sink

This study addresses the thermo‐diffusion and the diffusion‐thermo phenomena in a semi‐infinite absorbent channel whose walls are contracting/expanding, with heat source/sink effects. The governing partial differential equations with suitable boundary conditions are transformed to a system of dimensionless ordinary differential equations. An analytic solution of the problem has been found using a technique called homotopy analysis method (HAM). HAM gives consistently valid answers to the problem over an extensive variety of parameters and also provides better accuracy. To validate the analytical results, a comparison has been presented with a numerical solution calculated by using the parallel shooting method. The effects of dimensionless parameters, that is, deformation parameter, Reynolds number, Soret and Dufour numbers, and heat source/sink parameter on the expressions of velocity, temperature, and concentration profiles are analyzed graphically to understand the physics of the deformable channel. It has been noted that the velocity across the channel is higher for the expanding channel, as compared to that for the contracting channel. Also the Soret and Dufour number increases the temperature of the fluid, and decreases the concentration. The temperature profile has an increasing behavior in the case of heat source, and a decreasing behavior in the case of heat sink.     

Mechanophysical Cues in Extracellular Matrix Regulation of Cell Behavior

The extracellular matrix (ECM) is a macromolecular network that can provide biochemical and structural support for cell adhesion and formation. It regulates cell behavior by influencing biochemical and physical cues. It is a dynamic structure whose components are modified, degraded, or deposited during connective tissue development, giving tissues strength and structural integrity. The physical properties of the natural ECM environment control the design of naturally or synthetically derived biomaterials to guide cell function in tissue engineering. Tissue engineering is an important field that explores physical cues of the ECM to produce new viable tissue for medical applications, such as in organ transplant and organ recovery. Understanding how the ECM exerts physical effects on cell behavior, when cells are seeded in synthetic ECM scaffolds, is of utmost importance. Herein we review recent findings in this area that report on cell behaviors in a variety of ECMs with different physical properties, i.e., topology, geometry, dimensionality, stiffness, and tension.     

Design and Characterization of a New pVII Combinatorial Phage Display Peptide Library for Protease Substrate Mining Using Factor VII Activating Protease (FSAP) as Model

We describe a novel, easy and efficient combinatorial phage display peptide substrate-mining method to map the substrate specificity of proteases. The peptide library is displayed on the pVII capsid of the M13 bacteriophage, which renders pIII necessary for infectivity and efficient retrieval, in an unmodified state. As capture module, the 3XFLAG was chosen due to its very high binding efficiency to anti-FLAG mAbs and its independency of any post-translational modification. This library was tested with Factor-VII activating protease (WT-FSAP) and its single-nucleotide polymorphism variant Marburg-I (MI)-FSAP. The WT-FSAP results confirmed the previously reported Arg/Lys centered FSAP cleavage site consensus as dominant, as well as reinforcing MI-FSAP as a loss-of-function mutant. Surprisingly, rare substrate clones devoid of basic amino acids were also identified. Indeed one of these peptides was cleaved as free peptide, thus suggesting a broader range of WT-FSAP substrates than previously anticipated.     

Microwave dielectric properties of SrLa[Ga1−x(Mg0.5Ti0.5)x]O4 and SrLa[Ga1−x(Zn0.5Ti0.5)x]O4 (x = 0.2-0.8) ceramics

SrLa[Ga_1−x(R_0.5Ti_0.5)_x]O₄ (R = Mg, Zn) ceramics were prepared by a standard solid state sintering method. The single-phase ceramics with K₂NiF₄-type layered perovskite structure and I4/mmm space group were obtained, indicating that SrLa(R_0.5Ti_0.5) and SrLaGaO₄ can form the unlimited solid solutions. With increasing x for R = Mg and Zn, ε_r increases monotonously, the Qf value first increases and then decreases, while τ_f increases from a negative to a positive value. The optimized microwave dielectric properties were obtained as following: ε_r = 23.3, Qf = 89 400 GHz, τ_f = −0.8 ppm/°C for SrLa[Ga_0.6(Mg_0.5Ti_0.5)_0.4]O₄ and ε_r = 23.3, Qf = 76 200 GHz, τ_f = 0.2 ppm/°C for SrLa[Ga_0.7(Zn_0.5Ti_0.5)_0.3]O₄, indicating that the present solid solution ceramics are the promising candidates as microwave resonator materials for the telecommunication applications.     

Development of LTCC micro-hotplate with PTC temperature sensor for gas-sensing applications

Low temperature co-fired ceramic (LTCC) micro-hotplates show wide applications in gas sensors and micro-fluidic devices. It is easily structured in three-dimensional structures. This paper presents the low power consumption micro-hotplates which were developed with PTC (positive temperature coefficient) temperature sensor and inter-digitated electrodes. The paper presents two different structures for micro-hotplate with platinum as a heating element. The PTC temperature sensor using two different materials viz. PdAg and platinum paste are developed with micro-hotplates. The simulation has been achieved through COMSOL for LTCC and alumina micro-hotplates. The temperature variation with power consumption has been measured for the developed LTCC micro-hotplates. The change in resistance of PTC temperature sensors was measured with micro-hotplate temperature. The aim of this study was to place a temperature sensor with the gas sensor module to measure and control the temperature of micro-hotplate. A SnO₂ sensing layer is coated on LTCC micro-hotplate using screen printing and characterized for the sensing of carbon monoxide gas (CO). This study will be beneficial for designing hotplates based on LTCC technology with low power consumption and better stability of temperature for gas-sensing applications.     

太赫兹超表面计算全息

全息术是一种三维成像技术,它已经被应用于多种实际场景。随着计算机科学与技术的迅猛发展,计算全息由于其方便和灵活的特性,已经成为一种广泛应用的全息成像方法。本文回顾了我们近期基于超表面的太赫兹计算全息研究进展。其中,作为全息板的超表面展示出了超越传统光学器件的独特性能。首先,利用超表面实现了对于全息板每个像素的相位振幅同时且独立的调控,进而实现了高质量全息成像。这种新的电磁波操控能力也带来了新的全息成像效果,如利用介质超表面实现了全息像沿传播方向上的连续变化。其次,对超表面在不同偏振态下的响应进行设计,分别实现了线偏振态与频率复用、圆偏振态复用、以及基于表面波的偏振复用超表面全息术。此外,本文提出了依赖于温度变化而主动可控的超表面全息术,为今后计算全息术的设计与实现提供了新的方案,也推动了超表面在实际应用方面的发展。     

Adaptive Finite-time Tracking Control for Class of Uncertain Nonlinearly Parameterized Systems with Input Delay

International Journal of Control, Automation and Systems - In this paper, the tracking problem for a class of uncertain nonlinearly parameterized systems with input delay based the adaptive...     

Moderate lameness leads to marked behavioral changes in dairy cows

Lameness is one of the most prevalent diseases affecting the welfare of cows in modern dairy production. Lameness leads to behavioral changes in severely lame cows, which have been investigated in much detail. For early detection of lameness, knowledge of the effects of moderate lameness on cow behavior is crucial. Therefore, the behavior of nonlame and moderately lame cows was compared on 17 Swiss dairy farms. On each farm, 5 to 11 nonlame (locomotion score 1 of 5) and 2 to 7 moderately lame (locomotion score 3 of 5) cows were selected for data collection in two 48-h periods (A, B) separated by an interval of 6 to 10 wk. Based on visual locomotion scoring, 142 nonlame and 66 moderately lame cows were examined in period A and 128 nonlame and 53 moderately lame cows in period B. Between these 2 periods, the cows underwent corrective hoof trimming. Lying behavior, locomotor activity, and neck activity were recorded by accelerometers (MSR145 data logger, MSR Electronics GmbH, Seuzach, Switzerland), and feeding and rumination behaviors by noseband sensors (RumiWatch halter, ITIN + HOCH GmbH, Liestal, Switzerland). Furthermore, visits to the brush and the concentrate feeder, and the milking order position were recorded. In comparison with nonlame cows, moderately lame cows had a longer lying duration, a longer average lying bout duration, and a greater lateral asymmetry in lying duration. Average locomotor activity, locomotor activity during 1 h after feed delivery or push-ups, and average neck activity were lower in moderately lame cows. Eating time and the number of eating chews (jaw movements) were reduced in moderately lame compared with nonlame cows, whereas no effect of moderate lameness was evident for ruminating time, number of ruminating chews and boluses, and average number of ruminating chews per bolus. Moderately lame cows visited the concentrate feeder and the brush less frequently, and they were further back in the milking order compared with nonlame cows. In conclusion, nonlame and moderately lame cows differed in a biologically relevant way in many of the behavioral variables investigated in this study. Therefore, the use of these behavioral changes seems to be promising to develop a tool for early lameness detection.