基于粗轧镰刀弯的精轧跑偏预控模型及应用

带钢热轧跑偏问题是影响带钢生产与板形质量的重要因素。轧制生产过程中,由于粗轧中间坯头部弯曲导致的精轧堆钢事故频发,不仅严重危害生产稳定性,还造成资源的严重浪费和企业的经济损失。为了解决上述问题,针对粗轧非对称板形影响因素,结合实测粗轧中间坯以及工艺过程数据,建立中间坯头部预控模型,并利用加权最小二乘法与模型自学习对模型增益系数进行优化,最终建立了基于粗轧镰刀弯的精轧跑偏预控模型。将模型计算值应用于现场生产后,有效降低了精轧带钢头部跑偏,具有较好的参考价值和指导意义。     

激光合金化熔池成分均匀性与形状系数的关系SCIEI

本文研究了激光工艺参数对镀Cr中碳低合金钢激光合金化熔池形状系数及成分均匀性的影响。实验结果表明,熔池成分均匀性取决于其截面形状系数,后者是光束功率密度和交互作用时间的函数。在功率密度一定时,形状系数与交互作用时间成线性关系。当形状系数为1.6—3.0时,可以获得成分均匀的熔池。     

MAGNETIC PROPERTY AND THERMOSTABILITY OF Fe-BASE AMORPHOUS ALLOYS WITH HIGH SATURATION MAGNETIZATION

非晶态Fe_80B_(20),Fe_(17.84)B_(16.81)Si_(3.49)C_(1.36),Fe_(65.66)Co_(17.3)B_(15.84)Si_(1.2)和Fe_(6(?).92)Co_(17)B_(19.29)Si_(1.59)C_((?).(?))P_((?).(?))合金用单辊急冷法制备.测量了饱和磁化强度与温度的关系.得到0K时的原子磁矩(?)都在2.03—2.07μ_B之间.非晶态Fe_(80)B_(20)和Fe_(77.84)B_(16.81)Si_(3.49)C_((?).(?))合金的室温饱和磁化强度σ_s(R.T.)和Curie温度Tc相近,而含Co样品的σ_s(R.T.)和T_c分别高于Fe_(80)B_(20)约6%和13%.由热磁、电阻率、差热分析和X射线衍射的测量结果分析了样品的晶化转变.含Co样品的晶化温度T_(cr)与Fe_(80)B_(20)相近,而Fe_(77.84)B_(16.81)Si_(3.49)C_(1.86)的T_(cr)高于Fe_(80)B_(20)约80K.用化学键、T_(cr)与e/α的关系以及晶化过程的复杂性讨论了影响高饱和非晶态合金稳定性的因素.     

铝锡合金摩擦磨损性能的研究

研究了含锡量3%～30%铝锡合金的摩擦磨损性能,结果表明:随着含锡量的增加,铝锡合金的承载能力下降,摩擦系数下降.该合金的显微组织为硬的铝锡固溶体基体上分布着软的锡相质点.常温下含锡量在9%时,合金具有优良的耐磨减摩的综合性能.     

熔体过热处理对定向凝固界面形态及稳定性的影响

介绍了固液界面形态及稳定性的判据,即成分过冷理论和绝对稳定理论;简述了国内熔体过热处理的研究;详细阐述了熔体过热处理影响定向凝固界面形态及稳定性的现象及理论研究.并对今后熔体过热处理在定向凝固技术中的研究方向作了展望.     

陶瓷热压铸成型的超临界CO2流体脱蜡

利用超临界CO2流体萃取技术从陶瓷热压铸成型坯体中萃取有机粘合剂。对陶瓷热压铸成型中所使用的有机载体组分进行研究，对陶瓷热压铸成型超临界CO2流体脱蜡工艺条件进行了探索。研究了陶瓷坯体厚度、萃取压力，温度及时间对萃取率和陶瓷坯体脱蜡质量的影响。结果表明：由60％(质量分数，下同)非极性分子石蜡(熔点57℃)和40％极性分子蜂蜡(熔点58℃)组成的混合蜡作为热压铸浆料的有机载体，在压力为30MPa，温度为45℃的超临界CO2流体中脱脂可获得无缺陷的陶瓷热压铸成型生坯，脱蜡时间从34h减少到3h。由超临界CO2流体脱蜡后烧成的陶瓷试件具有小的变形及高的致密度。     

Acidolysis Reaction of Sal Fat (Shorea robusta) with Palmitic Acid

Acidolysis reaction of sal fat (Shorea robusta) with palmitic acid has been studied in relation to the operating variables like catalyst system and concentration, reaction temperature and time and molar ratios of reactants with the object of introducing more palmitic acid which is low in sal fat. The results demonstrate that as low as 2.5% and as high as 39% palmitic acid can be introduced in sal fat at the expense of other acids under the influence of various operating conditions. The products obtained differ from original sal fat in respect of chemical composition and slip point. The importance of such study is that there are possibilities of getting plastic fats of diverse properties for edible and industrial uses.     

Improvement of polymer blend properties by changing sequence of mixing

The basic objective of this article is to improve the polymer blend properties by changing mixing sequence. Blending of two elastomers does not lead to a molecularly homogeneous blend (true solution), but to a heterogeneous system in which both polymer phases are present. In this article, the detailed study of heterogeneous distribution of carbon black as well as blend inhomogenity and the physicomechanical including dynamic mechanical properties of the blend has been carried out. The choice of the blend was natural rubber/polybutadiene rubber as 85:15. Heterogeneous carbon black distribution study was also performed in differential scanning calorimeter. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2735–2742, 2007     

Viscous flow past a porous sphere with an impermeable core : effect of stress jump condition

An arbitrary flow of a viscous, incompressible fluid past a porous sphere of radius `a' with an impermeable core of radius `b', using Brinkman's equation in the porous region is discussed. At the interface of the clear fluid and porous region, stress jump boundary condition for the tangential stresses along with the continuity of normal stresses and the velocity components are used. On the surface of the impermeable core no slip condition is used. The corresponding Faxen's laws are derived to compute the drag and torque acting on the surface r=a. It is found that the drag and torque not only change with the change of the permeability, but also a significant effect of the stress jump co-efficient is observed. The variation of drag and torque with permeability for different thickness (a-b) of the porous region as well as for different values of stress jump coefficient is discussed when the basic flow is due to uniform flow, two dimensional irrotational flow, doublet in a uniform flow, stokeslet, rotlet. In case of uniform flow the flow field has been plotted. In all the cases, a significant effect of the stress jump coefficient has been realized.     

轴流压气机旋转失速建模与检测II: 基于北航低速压气机试验台的实验研究

轴流压气机旋转失速和喘振的提前检测对于提高压气机工作效率和稳定性具有重要的意义.本文以北京航空航天大学航空发动机重点实验室的低速轴流压气机实验台为研究对象,基于确定学习理论及动态模式识别方法,开展旋转失速初始扰动近似准确建模和快速检测研究.首先,在压气机机匣壁面周向布置多个动态压力传感器,获取压气机失速前和失速先兆的动态压力信号,基于确定学习理论对旋转失速初始扰动的内部系统动态进行建模;其次,基于以上建模,利用微小振动故障检测方法实现对旋转失速的离线和在线提前检测.实验结果表明,本文所提方法能够在不同转速情况下,提前0.3 s~1 s实现对旋转失速的实时在线检测.