U(Ⅳ)-U(Ⅵ)同位素交换反应动力学研究 Ⅰ.Fe~(2+)对U(Ⅳ)-U(Ⅵ)同位素交换反应的催化作用

一、前言由于U(IV)-U(VI)同位素交换体系具有相当大的同位素效应和很好的稳定性,并且容易实现两相回流,这对于分离U同位素的工业应用都是十分有利的。但是,U(IV)-U(VI)同位素交换反应速度非常慢,常温下H~+浓度为1.0—4.0 mol/l时,速度常数为1.0×10~(-4)l~2/mol·s。因此要用U(IV)-U(VI)交换体系浓缩铀同位素,必须研究U(IV)-U(VI)交换反应动力学,找到加快交换反应的方法。     

石家庄市室内氡及其子体浓度

本文报道了用双滤膜法对石家庄市室内空气中氡及其子体浓度的调查结果。47个房间室内氡年平均浓度为17.0Bq·m~(-3),氡子体平均浓度是7.14Bq·m~(-3)。氡及其子体浓度的日变化是清晨4—8时出现峰值。季节变化是夏秋季低,冬季高,全年的最低值出现在8月,最高值出现在11月。     

智能小区中的网络和布线设计解决方案——智能建筑学术讨论系列文章之七

当前小区信息网络建设中存在多种实施方案。笔者分析比较了常用的几种典型方案的优劣。讨论了目前建设中的一些解决方法，提出了兼顾现状，适度超前的设计实施原则。     

用于重离子核反应实验测量的纵向电场气体电离室

本文报道了一种新型的大动态范围，多叠层探测器系统组件之一的纵向电场气体电离室的构造，性能和在中能得离子核反应实验中的应用。     

~（60）Co辐照对聚四氟乙烯表面润湿性的影响

研究了具有低表面能的氟聚合物聚四氟乙烯（ＰＴＦＥ），经６０Ｃｏγ射线辐照后表面状态的变化，以及其对液体介质蒸馏水的润湿性。较详细地论述了辐照后表面粗糙度、结晶度以及表面化学基因等不同因素对ＰＴＦＥ表面润湿性的影响。通过对ＰＴＦＥ及其表面的红外、Ｘ光衍射，表面粗糙度的分析，弄清了辐照后ＰＴＦＥ表面化学基团的改变对有机氟聚合物表加的润湿性影响很大，而粗糙度和结晶度的变化对润湿性影响较小。     

高质量的一级光栅1．55μmDFB激光器

本文详细叙述了ＤＦＢ激光器的设计要点和新的工艺。采用一级全息光栅和二步液相外延法批量研制出高稳定单纵模工作的１．５５μｍ分布反馈激光器（ＤＦＢ—ＬＤ）。外延片成品率＞４０％。器件特性：２５℃时阈值电流２０ｍＡ，单面光功率＞１０ｍｗ，主边模抑制比ＳＭＳＲ达４３ｄＢ（λ／４相移光栅），谱线宽度△ν－２０ｄＢ＝０．３ｎｍ，调制速率＞１．８ＧＨｚ。可靠性测试显示：高温监测光谱稳定，２５°Ｃ时阈值退化率△Ｉｔｈ／ｔ＜０．３ｍＡ／ｋｈ，对应器件预估寿命将超过１０万ｈ。     

Micromechanical characterisation of fibre/matrix interfaces

Theoretical analyses for the single fibre pull-out and push-out models under monotonic loading are given which are based on a shear-lag analysis in a fracture mechanics approach considering non-constant friction at the debonded interface as a result of fibre Poisson contraction (or expansion). The solutions allow the determination of typical fibre/matrix interfacial properties such as the interfacial fracture toughness, G_ic, the coefficient of friction, μ, and the residual clamping stress, q₀. Under cyclic loading the interfacial properties are expected to degrade as a result of repetitive abrasion, and a power law function is assumed between μ and the number of elapsed cycles, N. However, G_ic is assumed to be unaffected and a fracture mechanics based debond criterion is derived for the relationship between the external applied stress, the debond length and the reduced friction coefficient for both fibre pull-out and fibre push-out. In addition, the relative displacements between the free fibre end and the matrix top are obtained for cyclic fatigue when the fibre is loaded and unloaded. A relationship obtained for the protrusion (or intrusion) length in fibre pull-out (or push-out) experiments allows the severity of the interface frictional degradation to be evaluated and characterised. Similarities and differences in the frictional degradation behaviour between fibre pull-out and push-out are also identified.     

Flammability and thermal stability studies of ABS/Montmorillonite nanocomposite

Acrylonitrile–butadiene–styrene (ABS)/montmorillonite nanocomposites have been prepared using a direct melt intercalation technique by blending ABS and organophilic clay of two different particle sizes: OMTa (5 µm) and OMTb (38 µm). Their structure and flammability properties were characterized by X‐ray diffraction, high resolution electronic microscopy (HREM), thermogravimetric analysis (TGA) and cone calorimeter experiments. The results of HREM showed that ABS/5 wt% OMTa nanocomposite was a kind of intercalated–delaminated structure, while ABS/5 wt% OMTb nanocomposite was mainly an intercalated structure. The nanocomposites showed a lower heat release rate peak and higher thermal stability than the original ABS by TGA and cone calorimeter experiments. Also, the intercalated nanocomposite was more effective than an exfoliated–intercalated nanocomposite in fire retardancy. Copyright © 2003 Society of Chemical Industry