Cellulose nanocrystals reinforced poly(oxyethylene)

Nanocomposite materials were prepared from poly(oxyethylene) (POE) as the matrix and a stable aqueous suspension of cellulose nanocrystals extracted from tunicate as the reinforcing phase. After dissolving POE in water and mixing with the cellulose nanocrystals suspension, solid films were obtained by casting and evaporating the preparations. Resulting films were characterized using scanning electron microscopy, differential scanning calorimetry, thermogravimetric analysis and dynamic mechanical analysis. Favorable interactions between cellulose and POE were evidenced and assumed to be partially responsible for a decrease of the crystallinity of the matrix. A thermal stabilization of the nanocomposites for temperatures higher than the melting temperature of POE was reported and ascribed to the formation of a rigid cellulosic network within the matrix assumed to be governed by a percolation effect. The formation of this percolating network was not altered by the matrix crystallization process and filler/POE interactions.     

Plasticized nanocomposite polymer electrolytes based on poly(oxyethylene) and cellulose whiskers

Nanocomposite polymer electrolytes based on a plasticized high molecular weight poly(oxyethylene) (POE) reinforced with high aspect ratio cellulose nanoparticles were reported. The influence of tetra(ethylene) glycol dimethyl ether (TEGDME) as plasticizer is investigated. The study mainly focuses on the dynamic mechanical behavior and ionic conductivity performances. The miscibility of the blend POE/TEGDME was investigated using both thermal and mechanical investigations. Viable polymer electrolytes can be obtained from this combination, conciliating acceptable ionic conductivities and outstanding mechanical performances on a large temperature range.     

Economical evaluation of electricity generation considering externalities

The economics of renewable energy are the largest barrier to renewable penetration. Nevertheless, the strong desire to reduce environmental emissions is considered a great support for renewable energy sources. In this paper, a full analysis for the cost of the kWh of electricity generated from different systems actually used in Egypt is presented. Also renewable energy systems are proposed and their costs are analyzed. The analysis considers the external cost of emissions from different generating systems. A proposed large scale PV plant of 3.3 MW, and a wind farm 11.25 MW grid connected at different sites are investigated. A life cycle cost analysis for each system was performed using the present value criterion. The comparison results showed that wind energy generation has the lowest cost, followed by a combined cycle–natural gas fired system. A photovoltaic system still uses comparatively expensive technology for electricity generation; even when external costs are considered the capital cost of photovoltaic needs to be reduced by about 60% in order to be economically competitive.     

Hand infections due to non-cholera Vibrio after injuries from St Peter's fish (Tilapia zillii)

We report 49 patients with a wide variety of hand infections, which developed after injuries from St Peter's fish (Tilapia zillii). Twenty-eight of 36 patients who had been operated on had non-cholera Vibrio infections, all identified as Vibrio vulnificus. The course in these patients was characterized by rapid spread of the infection with progressive necrosis of the tendon sheath, subcutaneous tissues and the skin. Two of them required amputations but the others had satisfactory functional results. Thirteen other patients were managed nonoperatively with intravenous antibiotics and all of them recovered completely.     

Effects of Fluids on the Simulated Clinical-Dental Machining of a Glass Ceramic

Effects of fluids on material removal rate, chipping damage, and surface roughness in the simulated clinical-dental machining of a dental-type glass ceramic were investigated. Significant differences in removal rate were obtained among the fluids investigated, but only a 4 wt% boric acid solution gave a higher removal rate than conventionally used water. Chipping damage was substantially lower for the boric acid and an oil-emulsion coolant compared with other fluids tested. Surface roughness was independent of the fluids used. The results indicate that improvement can be achieved in both material removal rate and machining damage by the appropriate selection of coolant chemistry.     

Randomized data selection in detection with applications to distributed signal processing

Performing robust detection with resource limitations such as low-power requirements or limited communication bandwidth is becoming increasingly important in contexts involving distributed signal processing. One way to address these constraints consists of reducing the amount of data used by the detection algorithms. Intelligent data selection in detection can be highly dependent on a priori information about the signal and noise. In this paper, we explore detection strategies based on randomized data selection and analyze the resulting algorithms' performance. Randomized data selection is a viable approach in the absence of reliable and detailed a priori information, and it provides a reasonable lower bound on signal processing performance as more a priori information is incorporated. The randomized selection procedure has the added benefits of simple implementation in a distributed environment and limited communication overhead. As an example of detection algorithms based upon randomized selection, we analyze a binary hypothesis testing problem, and determine several useful properties of detectors derived from the likelihood ratio test. Additionally, we suggest an adaptive detector that accounts for fluctuations in the selected data subset. The advantages and disadvantages of this approach in distributed sensor networks applications are also discussed.     

Minimum cost route for a highway in heterogeneous terrain

This paper shows that the minimum cost route should satisfy the Snell's law of light refraction and this can be done by successive iteration, in either a forward or backward direction. The number of iterations required for full convergence depends on the geometry of the problem and the cost ratio between each of the two neighbouring cost regions.     

Effect of Grain Size on Scratch Interactions and Material Removal in Alumina

Dramatic effects of scratch interactions on material removal are observed in alumina. A series of parallel scratches are made in aluminas with different grain sizes to investigate the influence of scratch interactions on the material removal process in abrasive machining. The separation distance between the two scratches and the normal load are varied and subsurface microfracture and damage modes are examined to assess the mechanisms of material removal. A very small amount of material is removed when the separation distance between the two parallel scratches is large or when the two scratches completely overlap. However, at intermediate distances the volume of material removed increases dramatically as a result of the interactions between the two scratches. The maximum amount of material removed and the corresponding distance between the two scratches are found to depend strongly on the grain size and the load. Observations of surface and subsurface damage reveal that grain dislodgement is the predominant mechanism of material removal, irrespective of the grain size. The relation between grain size, scratch interactions, and the material removal process in grinding and abrasive machining of ceramics is discussed in terms of the short-crack toughness of ceramics.