Computational Implementation of Asymmetric Integral Imaging by Use of Two Crossed Lenticular Sheets

We propose an asymmetric integral imaging method to adjust the resolution and depth of a three‐dimensional image. Our method is obtained by use of two lenticular sheets with different pitches fabricated under the same F/#. The asymmetric integral imaging is the generalized version of integral imaging, including both conventional integral imaging and one‐dimensional integral imaging. We present experimental results to test and verify the performance of our method computationally.     

Experimental investigation of natural convection from a horizontal ice surface melting in pure water

A study on natural convection from a horizontal ice surface melting in pure water was conducted experimentally for the ambient water temperature from 2▿C to 10°C. Natural convection flow around upward-or downward-facing horizontal ice plate was divided into three regions according to the temperature variation of ambient water. The flow patterns of three regions were no flow, two-dimensional steady laminar flow and unsteady flow. Mean Nusselt number for the upward-facing surface had its maximum value at about 3°C of ambient water temperature. However, in the case of the downward-facing surface it increased as the ambient water temperature increased.     

Effect of carbide additions on grain growth in TiC−Ni cermets

The growth of carbide particles in TiC-XC-2 vol.% Ni and TiC-XC-30 vol.% Ni alloys, where X=Zr, Cr, W, Ta and Mo, was fitted to an equation of the form d³-d_o ³=Kt. The grain growth behavior during liquid phase sintering at 1673K decreased markedly with the addition of Mo₂C or WC, changed little for TaC, and increased with the addition of ZrC or Cr₃C₂. The grain contiguity decreased with increasing Ni content in the TiC−Mo₂C−Ni alloy and was greater in the alloys with smaller growth rate constant. Consequently, the effect of carbide addition on the grain growth of 2 vol.% Ni alloys was found to be similar to that of 30 vol.% Ni alloys. The grain growth mechanism could be explained by the effect of contiguous carbide grain boundaries in restricting the overall grain growth, as well as the area of the solid/liquid interfaces in the alloy by the usual solution/reprecipitation model.     

Feature selection techniques and comparative studies for large-scale manufacturing processes

In order to efficiently and effectively control an overall process in the process industry, a few important parameters should be identified from high-dimensional, non-linear, and correlated data. Feature selection techniques can be employed to extract a subset of process parameters relevant to product quality. The performance of these techniques depends on the precision of the prediction model formulated to quantify the relationship between the process parameters and the quality characteristics. Although the neural network-based partial least squares (NNPLS) method has been proven to be effective in prediction models for the aforementioned industrial process data, feature selection techniques appropriate for NNPLS models have yet to appear. Here, several techniques for scoring the relevance of process parameters to product quality are proposed and validated by applying three datasets. These experiments show that the proposed techniques can discriminate relevant process parameters from irrelevant ones.     

Thermo-acoustic instability in the horizontal Rijke tube

The instability curve of a Rijke tube system was obtained accurately by following different paths of heat power and flow-rate for three regions and by defining its locus from the criterion based on the measured sound pressure levels. The unstable limits in the region of flow-rate lower than that at the minimal power are compared with previous data. To observe the effect of turbulence on the unstable limits, inflow turbulence was introduced by placing a bundle of circular cylinders upstream of the heating part (50< Re_d< 700). The large-amplitude inflow fluctuation may delay the transition of the chamber acoustic mode to the unstable zone even at a sufficient power.     

A 24-GHz 3.9-dB NF low-noise amplifier using 0.18 /spl mu/m CMOS technology

A 24-GHz low-noise amplifier (LNA) was designed and fabricated in a standard 0.18-/spl mu/m CMOS technology. The LNA chip achieves a peak gain of 13.1 dB at 24 GHz and a minimum noise figure of 3.9 dB at 24.3 GHz. The supply voltage and supply current are 1 V and 14 mA, respectively. To the author's knowledge, this LNA demonstrates the lowest noise figure among the reported LNAs in standard CMOS processes above 20 GHz.     

Aluminum deoxidation equilibrium in liquid Ni-Fe alloys equilibrated with CaO-Al2O3 slags

The deoxidation equilibrium for Al in Ni-Fe alloys was studied in the equilibrium experiments between CaO-Al₂O₃ slags and Fe-30, 50 and 70 % Ni alloys at 1873 K. By using the values for the first and second order interaction parameters between oxygen and nickel in liquid iron and those between oxygen and iron in liquid nickel, the effect of Ni on the activity coefficient of Al in liquid iron and that of Fe on the activity coefficient of Al in liquid nickel were determined in the whole composition range of Ni-Fe alloys. The oxygen contents in Ni-Fe alloys calculated by the iterative method based on pure iron were in good agreement with those based on pure nickel in the range of [% Al] < 0.03. From this fact, it was found that the Wagner's approximation relating to the multi-component solution was applicable to the deoxidation equilibrium in the whole composition range of Ni-Fe alloys in the restricted concentration of a deoxidizer.     

Numerical analysis of the warpage problem in TSOP

The reliability and the solderability of thin small outline package (TSOP) are significantly affected by the warpage that is generated after epoxy molding compound (EMC) molding process. This warpage problem mainly results from the mismatch of material properties such as Young's modulus, Poisson's ratio and coefficient of thermal expansion (CTE) and the geometric structure of each component for TSOP. The optimization of both material properties and geometric structures using the numerical analysis is necessary to reduce the warpage of TSOP. However, there are still some limitations for the numerical analysis to obtain proper results consistent with the practical warpage values. In this paper, the numerical analysis is performed under the assumption of elastic behavior for EMC. Furthermore, to solve the limitations, the material properties at the molding temperature and the degree of reaction rate at the end of the molding process of EMC are considered together for the analysis. This numerical analysis gives the higher warpage values than the measured ones, and is applicable to the practical design of the reliable electronic package.     

Influence of the silicon surface treatment by plasma etching and scratching on the nucleation of diamond grown in HFCVD - a comparative study

A comparative study for the nucleation of diamond was carried out using surface treatment like (i) surface scratching with 1 μm diamond paste and (ii) surface etching using chlorine plasma at different RF powers (50, 100 and 150 W). Atomic force microscopic study shows variation in roughness from 31 nm to 110 nm. Scratching results in random scratches, whereas plasma etches a surface uniformly. Scanning electron microscopic observations show well faceted crystallites with a predominance of angular shaped grains corresponding to 〈100〉 and 〈110〉 crystallite surfaces for the scratched as well as plasma etched substrate. Surface etching at 150 W plasma power results in a better growth in comparison with 50 and 100 W plasma powers. Chlorine-radical is found responsible for the changes in the growth morphology. Raman spectroscopy shows a sharp peak at 1,332 cm⁻¹ and a peak at ∼1,580 cm⁻¹ for both samples.