Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Preparation of monodisperse poly(vinyl alcohol) microspheres by heterogeneous surface saponification and iodine complex formation

Monodisperse poly(vinyl acetate) (PVAc) microspheres with high molecular weight obtained by suspension polymerization of vinyl acetate were saponified in alkaline aqueous solution to keep their spherical structure. The saponification was restricted on the surface of the PVAc microspheres and obtained particles had skin/core structure. Various poly(vinyl alcohol) (PVA) microspheres with different diameters and degrees of saponification (DSs) were obtained. The conversion of PVAc to PVA during the heterogeneous surface saponification time were examined by nuclear magnetic resonance spectroscopy and after 72 h hydrogel type PVA microspheres completely saponified were obtained. The crystal melting temperatures of the microspheres obtained by the saponification were measured a constant value of 238°C irrespective of varying DS, and the peaks became enlarged as reaction time. Iodine complexes were formed in saponified microspheres with DS of 41% and 99% by immersing them in I₂/KI aqueous solution and decomposed by the reduction of I₂ in the complexes to 2I^? using sodium sulfite to confirm whether the skin formed through the saponification was composed of PVA with high VA content. Obviously, characteristic blue color developments owing to I₅^?‐PVA complexes were observed in both saponified regions and a red in the PVAc core. Consequently, it was concluded that the PVA skins formed by heterogeneous surface saponification had high DSs. Such complexes endowed polymeric microspheres a good radiopacity which would be useful in clinical treatment of vascular diseases and were examined by X‐ray irradiation image. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of polymer modulus on the percolation threshold of latex-based composites

Monodispersed copolymer emulsions with different glass transition temperatures were synthesized to investigate the effect of room temperature polymer matrix modulus on the electrical properties of carbon black (CB) filled segregated network composites. The emulsion with the highest modulus at room temperature produced composites with the lowest percolation threshold. The threshold for a composite made from a copolymer latex containing an equal ratio of butyl acrylate and methyl methacrylate (BA5) is 1.5 vol%, while the percolation threshold for the much lower modulus BA7 (7:3 BA/MMA ratio) is 4.93 vol%. The microstructure of each composite shows significant differences in the level of CB dispersion within the polymer matrix. Higher modulus polymer particles push the CB more efficiently into the interstitial space between them, resulting in a lower percolation threshold. This modulus effect was confirmed by increasing the drying temperature, where the moduli of latexes (BA5, BA5.5, and BA6) were more similar and the percolation thresholds for three composites also become closer to one another.     

Effect of Li+ ions on structure,properties, and actuation of cellulose electro‐active paper actuator

We have reported an electro‐active paper actuator from regenerated cellulose. After dissolving cellulose fibers with a solution of lithium chloride in N,N‐dimethylacetamide, cellulose was regenerated by combining distillation of cellulose solution along with washing with the mixture of deionized water, isopropyl alcohol, and running water. However, the effect of Li⁺ ions on structure, properties, and the actuation behavior of the actuator was not studied. This article describes the changes in these parameters when the Li⁺ ions are removed by subjecting it to different running water exposure time. The structure and properties of cellulose electro‐active paper and its actuation behavior were studied. As Li⁺ ions content reduced from 4354.17 to 10.26 ppm by increasing the exposure time of running water, crystallinity, Young's modulus, and bending displacement decreased. Details about the investigation have been explained. This elimination of ions is important to increase the piezoelectric effect in EAPap by decreasing the ion migration effect. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

CO毒化AB5型合金分形特征研究

研究了三种贮氢合金 L a Ni5、L a Ni4 .7Al0 .3、Ml Ni4 .5Al0 .5被 10 0× 10 - 6 CO毒化后的分形特征 ,求出这三种合金在含 10 0× 10 - 6 CO的氢中循环 ,分维分别为 0 .2 5 4 7、0 .170 9、0 .0 72 5。可以较好的解释合金被毒化的宏观现象。     

二次电池电极基板用复合多孔金属材料的研究

介绍了一种复合金属多孔体的制备及其方法，首先以泡沫塑料为芯膜，经过导电化处理使其具有导电性，其次进行电沉积金属铁，再进行电沉积金属镍，经过热处理后可制备出复合金属多孔体。该复合金属多孔体用铁取代金属镍，其抗拉性能优于单质泡沫镍，同时可以降低制造成本，主要用于载体如电池电极。     

反应温度对聚苯胺薄膜生长的影响

在不同反应温度条件下采用原位聚合法在石英基片上制备了聚苯胺薄膜．对薄膜样品进行了紫外光谱、SEM、电性能表征。实验结果表明，过高的合成温度会加速聚合反应过程，抑制膜厚的增长，引起薄膜的热降解，进而对样品的导电性产生不良影响。根据生长速率与合成温度的依赖关系，估算了聚合反应的活化能Ea=34.4kJ/mol。     

有限元仿真分析中的结构周期差异探讨

针对有限元仿真分析中结构自振周期减小的问题，讨论了几种主要的影响因素，并借用商品化设计软件TBSA，ETABS 和有限元分析软件ANSYS，通过对一个简单结构的多次计算，比较了这些因素的影响大小。