Development of the gel pond technology

A review of the development of the gel pond technology is presented. First, the emergence and growth of solar pond technology since the 1950's is described. The inherent problems encountered with the conventional salt gradient ponds are discussed, leading to the concept of the solar gel pond in which the salt gradient layer in the former is replaced by a transparent polymer gel. The major work in the first phase dealt with the experimental development of a polymer gel which met certain selection criteria. The criteria considered included transmissivity, stability of physical and chemical properties, high viscosity and other physical and optical properties. The gradual development of the polymer gel through an alternating process of testing and elimination and evaluation of relevant properties of the gel has been described. Modeling and optimization studies of the solar gel pond have been presented. Bansal and Kaushik's model for a salt gradient pond has been modified for a solar gel pond, and the results of the simulation are presented in a graphical form to serve as a quick reference for estimation of pond surface area, depth and flow rate for heat extraction depending on the extreme temperature required in the storage zone and the required heat load. Then, a cost-benefit economic analysis compares the economics of a solar gel pond with a conventional salt gradient pond. The construction of an experimental gel pond (18 m²) at The University of New Mexico is described, and the results of the study are summarized. Information on commercial scale ponds at Chamberino, New Mexico (110 m²), and in Albuquerque, New Mexico (400 m²), is provided. The review of the technology demonstrates the immense potential of the gel pond as a source of alternate energy for the years ahead.     

Estimation of collapse moment for the wall-thinned pipe bends using fuzzy model identification

In this work, the collapse moment due to wall-thinned defects is estimated through fuzzy model identification. A subtractive clustering method is used as the basis of a fast and robust algorithm for identifying the fuzzy model. The fuzzy model is optimized by a genetic algorithm combined with a least squares method. The developed fuzzy model has been applied to the numerical data obtained from the finite element analysis. Principal component analysis is used to preprocess the input signals into the fuzzy model to reduce the sensitivity to the input change and the fuzzy model are trained by using the data set prepared for training (training data) and verified by using another data set different (independent) from the training data. Also, three fuzzy models are trained, respectively, for three data sets divided into the three classes of extrados, intrados, and crown defects, which is because they have different characteristics. The relative root mean square (RMS) errors of the estimated collapse moment are 0.5397% for the training data and 0.8673% for the test data. It is known from this result that the fuzzy models are sufficiently accurate to be used in the integrity evaluation of wall-thinned pipe bends and elbows.     

A genetic algorithm for the optimisation of assembly sequences

This paper describes a Genetic Algorithm (GA) designed to optimise the Assembly Sequence Planning Problem (ASPP), an extremely diverse, large scale and highly constrained combinatorial problem. The modelling of the ASPP problem, which has to be able to encode any industrial-size product with realistic constraints, and the GA have been designed to accommodate any type of assembly plan and component. A number of specific modelling issues necessary for understanding the manner in which the algorithm works and how it relates to real-life problems, are succinctly presented, as they have to be taken into account/adapted/solved prior to Solving and Optimising (S/O) the problem. The GA has a classical structure but modified genetic operators, to avoid the combinatorial explosion. It works only with feasible assembly sequences and has the ability to search the entire solution space of full-scale, unabridged problems of industrial size. A case study illustrates the application of the proposed GA for a 25-components product.     

Optical measurement of spindle radial motion by moiré technique of concentric-circle gratings

This paper describes an optical moiré method intended for the testing of the radial motion of a rotating spindle. Two concentric-circle gratings of fine pitches were configured for the radial motion to be directly detected by analyzing the interferometric fringes generated by the gratings. This method was immune to mechanical and electrical disturbances since neither master cylinder nor electrical gap gage was needed. Test results demonstrated that a measuring accuracy of less than 0.01 μm can practically be achieved using the method.     

Enhancement of hydrocyclone performance by controlling the inside turbulence structure

A new hydrocyclone was designed with a winged core fixed below the vortex finder in this study. With the winged core, the turbulence structure characteristics inside the hydrocyclone, including time-averaged pressure, pressure fluctuation, relative pressure fluctuation characteristics, and distribution characteristics of the probability density of the turbulence pressure, were all positively controlled. By controlling the turbulence structure, the performance of the new hydrocyclone was improved effectively. Compared with the common hydrocyclone, the new hydrocyclone was featured with lower energy loss coefficient, higher reduced separation efficiency, higher separation sharpness and larger capacity.     

Performance of asynchronous DS-CDMA using a maximal ratio combiningdiversity over a Rician fading channel

The final closed-form expression for bit error probability (BEP) is presented for a DS-CDMA system using a maximal ratio combining (MRC) diversity over a Rician fading channel. The accuracy of the BEP estimate evaluated by this expression is verified by comparison with a semi-analytic simulation result. The effect that diversity order has on the BEP is also considered for typical multipath delay profiles with different Rician ratios     

TES modeling for analysis of a video multiplexer

The transport of video images is likely to be a major application of high-speed networks of the future. These applications are capable of utilizing the high bandwidths that will become available with the advent of B-ISDN. In this paper, we propose a new methodology (called TES) for modeling the frame bitrate stream generated by compressed video sources. The main characteristic of this method is that it can model an arbitrary marginal distribution and approximate the autocorrelation structure of the random bitrate process generated by compressed frames. We present a modeling example utilizing this method, based on data from a video coding algorithm employing a layering technique. Using the source model, we develop a simulation model of a multiplexer of video sources. We show that this model can be used to address a number of design issues that arise in this class of problem. In particular, we show that for a layered video coding algorithm, it is possible to have a gain in the number of sources multiplexed at the cost of some loss of low priority packets.     

The role of grain-boundary on the hydrogen-induced degradation inthin-film ferroelectric capacitors

The electrical properties of thin-film ferroelectric capacitors are known to degrade severely when exposed to hydrogen. In this study, we directly measured the effects of the grain boundary on the hydrogen-induced degradation in ferroelectric Pb(Zr, Ti)O₃ (PZT) thin films by the location of the top Pt electrode either inside the grains or at the grain boundary. A strong relationship between the grain boundary and the electrical properties of ferroelectric capacitors as a result of hydrogen annealing was found. The degradation of the electrical properties in thin-film ferroelectric capacitors after hydrogen annealing is mainly due to the presence of the grain boundary in the ferroelectric thin film     

Adding Support for Persistence to CLOS via Its Metaobject Protocol

Language-level support for object persistence frees programmers from having to confront a broad class of database issues from within their applications. By virtue of its metaobject protocol, CLOS is a language whose semantics can be tailored by individual programmers. We used the metaobject protocol to extend CLOS with support for object persistence. Our goal was to obtain a version of CLOS with persistence to which we could easily port a commercial geometric CAD modeling system. We describe the design and implementation of our persistence extension and highlight the strengths and weaknesses exhibited by the CLOS metaobject protocol during our experiment. For many aspects of the implementation we found that the metaobject protocol was ideal. In other cases we had to choose among paying a large performance penalty, extending the protocol, and bypassing the protocol by modifying the language implementation directly.