Effect of various efficient vulcanization cure systems on the compression set of a nitrile rubber filled with different fillers

Effect of various efficient vulcanization (EV) sulfur cure systems on the compression set of a nitrile rubber filled with carbon black and silica/silane fillers was examined. The cure systems had different amounts of thiuram and sulfenamide accelerators and elemental sulfur, whilst the loading of zinc oxide and stearic acid activators was kept constant. The fillers had surface areas from 35 to 175 m²/g. In this study, the lowest compression set was measured for the rubber filled with carbon black with 78 m²/g surface area, which was cured with an EV cure system made of a small amount of elemental sulfur and large amounts of the two accelerators. Interestingly, a small change in the amount of elemental sulfur had a bigger effect on the compression set than did large changes in the loading of the accelerators in the cure system. Among the fillers, carbon black caused less compression set of the rubber vulcanizate than the silica/silane system did. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41512.     

Topology optimization of transient problem with maximum dynamic response constraint using SOAR scheme

Frontiers of Mechanical Engineering - This paper proposes a novel method for the continuum topology optimization of transient vibration problem with maximum dynamic response constraint. An...     

Towards the performance evaluation of 4th generation wireless communication standards: LTE versus Mobile WiMAX

Advances in wireless communication protocols and networking toward support of the next generation of mobile and radio broadband technologies have contributed to a strong competition among various telecommunication standards in particular Long Term Evolution (LTE) and Mobile Worldwide Interoperability for Microwave Access (WiMAX). In this paper, we provide an in‐depth comparison analysis of LTE and Mobile WiMAX at the physical (PHY) layer by studying the most similar PHY configuration scenarios for these two technologies. Our study includes a throughput analysis of downlink (DL) and uplink (UL) transmissions in time division duplex with the least overhead possible and different antenna schemes as well as modulation and code rates. This study also performs an overhead analysis in both protocols to provide a more in‐depth understanding of the PHY layer capacity in various PHY layer configurations. Our simulation results generally show higher performance for LTE in both DL and UL transmission with 7 Mbps in DL and 5 Mbps in UL, when using one antenna port. However, by increasing the number of antennas for multiple‐input/multiple‐output configurations, the results illustrate a reduction in the performance of LTE compared to Mobile WiMAX. This arises from the increase in reference signal overhead in LTE from 4.7% in single‐input/single‐output (SISO) to 14.28% in 4 × 4 multiple‐input/multiple‐output (MIMO). Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis of graphene-supported bimetallic nanoparticles for the sunlight photodegradation of Basic Green 5 dye in aqueous medium

Graphene nanosheets-supported Sn-Pt bimetallic nanoparticles (GNs/Sn-Pt) were prepared by precipitation method. The obtained GNs/Sn-Pt was used as a photocatalyst for photodegradation of Basic Green 5 (BG5) in aqueous solution under sunlight. The morphology and photodegradation study was performed by SEM and UV–VIS spectrophotometry, respectively. The SEM image showed the presence of Sn and Pt on GNs, being confirmed by energy dispersive X-ray (EDX) analysis. The photodegradation study of BG5 showed that the dye degradation increases as a function of irradiation time. The degradation of BG5 was found to be pH dependent and maximum degradation was found at higher pH.     

Influence of plasticizers and cryogenic grinding on the high‐cooling‐rate solidification behavior of PBT/PET blends

Two structurally different plasticizers (cyclic and linear) and the effect of cryogenic grinding on the solidification behavior at high cooling rates by a continuous cooling transformation approach of poly(butylene terephthalate)/poly(ethylene terephthalate), PBT/PET, blends are described. The solidification curve (density versus cooling rate) is confirmed as an effective tool to compare the differences in crystallization behavior under conditions mimicking processing. In comparison to the bulky cyclic plasticizer, the linear oligomeric one was found to have a more pronounced influence on the crystallization behavior. A 60/40 by weight PBT/PET blend shows a drop‐off of density at ～50 K/s. In the plasticized sample, the long‐range crystalline order appears up to a cooling rate of ～250K/s, making the blend comparable to pure PBT. Grinding the components before blending further improves crystallizability and synergy to the addition of the plasticizer. The results suggest the important role of local chain mobility in the solidification behavior at high cooling rates. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43083.     

Investigation of structure and mechanical properties of toughened poly(l‐lactide)/thermoplastic poly(ester urethane) blends

In this study, poly(l ‐lactide) (PLA) is melt‐blended with thermoplastic polyurethane (TPU) to modify the brittleness of PLA. An aliphatic ester‐based TPU was selected in order to have an ester sensitivity for degradation and an inherent biocompatibility. Using this compatible TPU, there was no need to apply problematic compatibilizers, so the main positive properties of PLA such as biocompatibility and degradability were not challenged. The detected microstructure of PLA/TPU blends showed that when the TPU content was lower than 25 wt %, the structure appeared as sea‐islands, but when the TPU content was increased, the morphology was converted to a cocontinuous microstructure. A higher interfacial surface area in the blend with 25 wt % TPU (PLA25) resulted in a higher toughness and abrasion resistance. The various analyses confirmed interactions and successful coupling of two phases and confirmed that melt‐blending of PLA with the aliphatic ester‐based TPU is a convenient, cost‐effective, and efficient method to conquer the brittleness of PLA. The prepared blends are general‐purpose plastics, but PLA25 showed an optimum mechanical strength, toughness, and biocompatibility suitable for a wide range of applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43104.     

Electrochemical Synthesis of Cu (II) Coordination Polymer Coatings Based on 2,2′-Thiodiacetic Acid and 1,2,4,5-Benzenetetracarboxylate

Electrochemical synthesis of coordination polymers of Cu(II), [Cu(TDA)]_n and [Cu₂(BTC)(H₂O)₆?6H₂O]_n in which H₂TDA is 2,2′-thiodiacetic acid and BTC stands for 1,2,4,5-benzenetetracarboxylate was carried out by the electrochemical oxidation of Cu anode in the presence of H₂TDA (a flexible ligand), and 1,2,4,5-benzentetracarboxylic acid (H₄BTC) (a rigid ligand) in aqueous solutions. The structure of coordination polymers were characterized by scanning electron microscopy, X-ray powder diffraction, elemental analysis, thermal gravimetric and differential thermal analyses. The crystal structure of the compounds consists of one-dimensional cubical crystal polymeric units of [Cu(TDA)]_n and [Cu₂(BTC)(H₂O)₆?6H₂O]_n. Furthermore, the coordination number of Cu (II) ions in synthesized coordination polymers to be found five. The main advantages of electrosynthesis are the minor synthesis time, the milder conditions and the facile synthesis of coordination polymer coatings.