Simple and Sensitive HPLC Method with Fluorescence Detection for the Measurement of Ibuprofen in Rat Plasma: Application to a Long-Lasting Dosage Form

A simple and sensitive high-performance liquid chromatography (HPLC) assay applied to the measurement of ibuprofen in rat plasma has been developed. Two parameters have been investigated to improve ibuprofen detectability using fluorescence detection: variation of mobile phase pH and the use of β-cyclodextrin (β-CD). Increasing the pH value from 2.5 to 6.5 and adding 5 mM β-CD enhanced the fluorescence signal (λ_exc = 224 nm; λ_em = 290 nm) by 2.5 and 1.3-fold, respectively, when using standards. In the case of plasma samples, only pH variation significantly lowered detection and quantification limits, down to 10 and 35 ng/mL, respectively. Full selectivity was obtained with a single step for plasma treatment, that is, protein precipitation with acidified acetonitrile. The validated method was applied to a pharmacokinetic study of ibuprofen encapsulated in microspheres and subcutaneously administered to rats.     

Quantitative characterization of carrier injection across metal–organic interfaces using Bardeen theory

We have investigated the contact between a metal and an organic/polymeric (o/p) material and we have introduced a relation for carrier injection using Bardeen theory. A series of narrow barriers is considered in the semiconductor side to account for the localized nature of the carriers in the o/p material. As an application of the model, we have calculated the hopping rate of carriers in terms of the contact parameters. Also, we have discussed the hopping of carriers deep into the organic dielectric. Finally, we have explored the hopping rate in practical contacts between polyfluorene-based polymers and different electrodes.     

Strictly periodic scheduling in IMA-based architectures

The avionic industry has recently adopted the Integrated Modular Avionics (IMA). Such architectures allow the execution of avionic functions on a shared computing platform while avoiding any interference between them. This is done through hard memory and temporal segregation constraints. Although IMA reduces the weight and the power consumption and shortens the design-cycle times, it gives rise to a complex multiprocessor scheduling problem. One of the key difficulties of this problem is related to the strict periodicity of tasks, which means that the time separating two successive executions of the same task is strictly equal to the associated period. In order to help the system designer in producing a proper schedule, an exact formulation based on Integer Linear Programming and a heuristic inspired from Game Theory are proposed. To enhance the solution quality of the heuristic, a?multi-start method, which gives some probabilistic guarantees on the optimality of the solutions, is also introduced.     

Sensing and identification of carbon monoxide using carbon films fabricated by methane arc discharge decomposition technique

Carbonaceous materials have recently received attention in electronic applications and measurement systems. In this work, we demonstrate the electrical behavior of carbon films fabricated by methane arc discharge decomposition technique. The current-voltage (I-V) characteristics of carbon films are investigated in the presence and absence of gas. The experiment reveals that the current passing through the carbon films increases when the concentration of CO₂ gas is increased from 200 to 800 ppm. This phenomenon which is a result of conductance changes can be employed in sensing applications such as gas sensors.     

The effect of sliding speed and amount of loading on friction and wear behavior of Cu–0.65 wt.%Cr alloy

Friction and wear behavior of a peak aged Cu–0.65 wt.%Cr alloy was investigated. The friction and wear experiments were run under ambient conditions with a pin-on-disk tribometer. Experiments were performed using various applied normal loads and sliding velocities. The tribological behavior of the studied alloy was discussed in terms of friction coefficient, wear loss and wear mechanism.Friction coefficient and wear loss have shown large sensitivity to the applied normal load and the sliding velocity. At the sliding velocity of 0.3 m/s weight loss increased from 6.9 to 51 mg by increasing the normal load from 20 to 40 N. At higher sliding velocity minimum weight loss is achieved at 60 N normal load. So it can be seen that with increasing normal load wear rate decreases due to the formation of a continuous tribofilm which consists of Fe–Cu intermetallic. Varying of friction coefficients in different conditions of normal load and sliding velocity is correlated to the wear behavior.The analysis of worn surfaces by XRD and SEM showed that an increase in normal load and sliding velocity creates an intermetallic wear-induced layer, which modifies the wear behavior of the alloy. The XRD result indicates that new phase of Cu_9.9Fe_0.1 is generated on worn surfaces of the pin specimens during the wear tests. There is a significant correlation between the micrograph of worn surfaces and the wear rate of specimens.     

A THREE-PHASE MODEL FOR SORPTION ISOTHERM IN ZEOLITE ADSORBENTS

A three-phase model for adsorption in zeolite cavities is proposed. The adsorbed molecules are taken to be distributed between a surface layer and a dense phase filling the rest of the cavity volume. This model is a more realistic representation of molecules in zeolite cages especially at high pressures. The equation for the adsorption isotherm, based on this model, has two contributions: a surface term and a dense phase term. The dense phase contribution was estimated from a simple equation that obeys the limiting values at low and high pressures. The surface contribution can be estimated from the existing surface adsorption models. When all model parameters are estimated from molecular and literature data, the combination of the two terms was found to be an improvement over traditional treatment of adsorption data of a number of gases in zeolite-A for a wide range of pressures. However, new models for the adsorbed phase that account for sorbate-sorbate repulsive forces correctly are needed for accurate prediction of adsorption data.     

Micro‐morphological,environmental and phytochemical investigation of herbal medicines by using LM and SEM: A quality control tool

The use of quality control tool for authentication of Jadwar (Delphinium denudatum Wall. ex Hook.f. & Thomson), a folk herbal drug used for the treatment of different ailments, was studied. People face problems of adulteration for this drug at global, regional, national and local levels. Two different plant species are commercially marketed in the Indo‐Pak Subcontinent under the same trade name of Jadwar. One is D. denudatum Wall. ex Hook.f. & Thomson and the other is Aconitum heterophyllum Wall. ex Royle. To focus on this problem, a marketable available drug sample of Jadwar was authenticated by using basic microscopy tools (LM) and advanced chemo‐taxonomic markers. Authentication, quality and standardization of this drug was achieved using morphology, organoleptography, UV and IR analyses, scanning electron microscopy of pollen and anatomical investigations. The techniques used for authentication marked the clear difference between the studied plants. Microscopic studies, chemotaxonomic investigation and other techniques used in this project provided the basis for the authentication of this species.     

A comparative study of the tool–chip contact length in turning of two engineering alloys for a wide range of cutting speeds

Tool chip contact length is an important parameter in machining, as it provides an indication of the size of area of interaction between the hot chip and the tool surface and hence the interface heat transfer zone. Heat transfer and thermally activated wear modes usually dominate tool wear in the high speed machining of steels and machining of titanium alloys at most cutting speeds. In this study, existing models for the prediction of tool–chip contact length are reviewed and examined for their suitability in high speed machining of two widely used engineering alloys. Orthogonal turning tests for AISI 1045 steel and Ti6Al4V titanium alloy are conducted for a range of cutting speeds from conventional to high speeds. New contact length models are presented for both materials covering a wide range of cutting speeds. More significantly, these contact length models are appropriate for high speed machining where thermal loads significantly influence process performance. Additionally, the work discusses how the machinability of engineering materials influences the ability to predict contact length.