Fabrication and characteristics of high-speed implant-confined index-guided lateral-current 850-nm vertical cavity surface-emitting lasers

Process technology of high-speed implant-apertured index-guide lateral-current-injection top dielectric-mirror quantum-well 850-nm vertical cavity surface-emitting lasers (VCSELs) has been developed. Oxygen and helium implantation for aperture definition and extrinsic capacitance reduction, dielectric mirror formation, p- and n-ohmic contact formation, VCSEL resistance, and thermal analysis were investigated. Employing this technology, GaAs/AlGaAs-based 850-nm VCSELs with small signal modulation bandwidths up to 11.5 Gb/s and an eye diagram generated at 12 Gb/s by a pseudorandom bit sequence of 2/sup 31/-1 were achieved. The bit-error rates were below 10/sup -13/. The threshold current is as low as 0.8 mA for 7-/spl mu/m-diameter current apertures and typical slope efficiencies of 0.45-0.5 mA/mW were obtained.     

对当前汽轮发电机在线监测应用的初步分析和建议

根据国内外汽轮发电机在线监测的应用情况，提出配置在线监测应遵循的原则，在对当前各种在线监测应用初步分析的基础上，提出合理配置在线监测的策略性建议。     

Nitride-based flip-chip ITO LEDs

Nitride-based flip-chip indium-tin-oxide (ITO) light-emitting diodes (LEDs) were successfully fabricated. It was found that the forward voltage and the 20 mA output power of the flip-chip ITO LED were 3.32 V and 14.5 mW, respectively. Although the operation voltage of such a flip-chip ITO LED was slightly larger, it was found that its output power was much larger than those of conventional nonflip-chip LEDs. It was also found that flip-chip ITO LEDs were more reliable.     

Luminescence Characterization of Mg Doped Y2O2S:Ti Long Afterglow Phosphor

Y1.94-xMgxO2S:0.06Ti (0≤x≤0.10) phosphors with long afterglow were synthesized by solid state reaction route. The photoluminescence spectra, decay curves, thermoluminescent spectra and chromaticity coordinate curves were investigated. The results show that the luminescence intensity of Y1.94-xMgxO2S:0.06Ti (0≤x≤0.10) phosphors decrease gradually with increasing Mg2 ion content, and the shape of luminescence spectra and chromaticity coordinate change as well. Furthermore, two thermoluminescent peaks in single Ti-doped Y2O2S sample are found at 91.8 and 221.5 ℃, respectively. Nevertheless, significant different spectra were found for the Mg, Ti co-doped Y2O2S samples that three thermoluminescence peaks appear at 52.3, 141.7 and 226.8 ℃, respectively. These results indicate that the co-doped Mg ion changes the inherent trap depth of single Ti-doped Y2O2S:Ti phosphor, and induces simultaneously a new trap level in the Y1.94-xMgxO2S:0.06Ti phosphor. Based on the analysis of thermoluminescent spectra, photoluminescent spectra, decay curve and crystal structure defect, it was proposed that the varied structure defect and introduced new trap level by the doped Mg2 ions should be responsible for reducing luminescence intensity and varying color in the Y1.94-xMgxO2S:0.06Ti phosphor.     

Optimal base-station locations in two-tiered wireless sensor networks

We consider generic two-tiered wireless sensor networks (WSNs) consisting of sensor clusters deployed around strategic locations, and base-stations (BSs) whose locations are relatively flexible. Within a sensor cluster, there are many small sensor nodes (SNs) that capture, encode, and transmit relevant information from a designated area, and there is at least one application node (AN) that receives raw data from these SNs, creates a comprehensive local-view, and forwards the composite bit-stream toward a BS. This paper focuses on the topology control process for ANs and BSs, which constitute the upper tier of two-tiered WSNs. Since heterogeneous ANs are battery-powered and energy-constrained, their node lifetime directly affects the network lifetime of WSNs. By proposing algorithmic approaches to locate BSs optimally, we can maximize the topological network lifetime of WSNs deterministically, even when the initial energy provisioning for ANs is no longer always proportional to their average bit-stream rate. The obtained optimal BS locations are under different lifetime definitions according to the mission criticality of WSNs. By studying intrinsic properties of WSNs, we establish the upper and lower bounds of maximal topological lifetime, which enable a quick assessment of energy provisioning feasibility and topology control necessity. Numerical results are given to demonstrate the efficacy and optimality of the proposed topology control approaches designed for maximizing network lifetime of WSNs.     

用脉冲全息法分析冲床的动态特性

介绍了双脉冲激光全息照相对机床结构动态特性的现场测量技术,并应用它成功地分析研究了冲床整机的动刚度和振型。     

A quantitative method for evaluating the performances of hyperspectral image fusion

Hyperspectral image fusion is a key technique of hyperspectral data processing. In recent years, many fusion methods have been proposed, but there is little work concerning evaluation of the performances of different image fusion methods. In this paper, a method called quantitative correlation analysis (QCA) is proposed, which provides a quantitative measure of the information transferred by an image fusion technique into the output image. Using the proposed method, the performances of different image fusion methods can be compared and analyzed directly based on the images of before and after performing the fusion. The correlation information entropy, based on the developed QCA, is also proposed and testified by numerical simulations. Typical hyperspectral data are applied to the proposed method. The results show that the method is effective, and its conclusions agree with the classification results in applications.     

Impact of Aspen Log Storage with and without Protection on OSB Performance

Outdoor log storage without protection can change the mechanical and chemical properties of wood due to infection by various fungi. To understand how outdoor log storage affects the wood and, subsequently, the strandboard quality, two piles of aspen logs were set up outside and stored for a period of four months (July to November). One of the piles was treated with a biological solution to prevent fungal growth. The other one was stored without treatment. Both piles contained non-debarked and partially debarked logs. Evaluation of sap stain development indicated that all logs had been colonized by staining fungi with average stain coverage of 9.37 to 57.18% and maximum stain penetration of 3.58 to 7.27 cm over the log cross section. The variation of fungal colonization depended on log treatment and bark condition. The most effective way to prevent stain growth was the combination of biological treatment and partial debarking. A series of strandboard was prepared from fresh and aged aspen logs. All boards made from stored logs were statistically comparable to or superior to the control boards made from fresh aspen logs. The boards made from treated/partially debarked and untreated/non-debarked logs were statistically comparable to each other except for wet MOR. In addition, these two board types were statistically stronger than other boards made from treated/non-debarked and untreated/partially debarked logs in terms of IB and water resistance. Some individual stained strands were observed on the finished board surface. Less staining was found in the boards prepared from biologically treated and partially debarked logs, compared with those made from other stored logs.