Towards a new definition of EPOC parameters for anionic electrochemical catalysts: case of propene combustion

The electrochemical promotion of catalysis (EPOC) of propene combustion was investigated using Pt sputtered thin film on an O²⁻ conductor, 8 mol% Y₂O₃-stabilized-ZrO₂ (YSZ). In order to separate the influence of the thermal migration of the O²⁻ oxide ions from the electrolyte to the catalyst surface and the impact of an electrical polarization on the catalytic activity, several light-off experiments (cool down and heat up procedures) were successively performed under different polarizations, i.e. OCV, +2 and −2 V. These experiments have clearly shown that the presence of O²⁻ (thermally or electrochemically induced) inhibits the catalytic activity of the platinum for the propene deep oxidation. These results demonstrate the importance to define a normalized rate enhancement ratio, ρ _n , from a reference value of the catalytic rate corresponding to a Pt surface state free of O²⁻ ions.     

A strategy for the electro-organic synthesis of new hydrocaffeic acid derivatives

Electrochemical treatment processes can significantly contribute to the protection of the environment through the minimization of waste and toxic materials in effluents. From a pharmaceutical point of view and due to the existing resemblance between the electrochemical and biological reactions, it can be assumed that the oxidation mechanisms on the electrode and in the body share similar principles. In this paper, the application of electrochemical studies in the design of an environmentally friendly method was delineated for the new hydrocaffeic acid (HCA, 3,4-dihydroxy hydrocinnamic acid) derivatives synthesis at carbon electrodes in an undivided cell. In this cell, the EC mechanism reaction was involved, comprising two steps alternatively; (1) electrochemical oxidation and (2) chemical reaction. In particular, the electro-organic reactions of HCA, an important biological molecule, were studied in a water–acetonitrile (90:10 v/v) mixture in the presence of benzenesulfinic acid (3) and p-toluenesulfinic acid (4). The research included the use of a variety of experimental techniques, such as cyclic voltammetry, controlled-potential electrolysis and product spectroscopic identification.     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.     

Synthesis,characterization, and redox and electrochromic behaviors of poly(3-n-octyloxythiophene)

Poly(3-n-octyloxythiophene), a conjugated polymer, which possessed solubility in common organic solvents, was synthesized by electrochemical polymerization in the presence of lithium perchlorate as the supporting electrolyte and sodium dodecyl sulfate as the surfactant in an aqueous medium. Characterizations of the intermediate, monomer, and polymer were performed by NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, and gel permeation chromatography. The process of electrochemical polymerization and the electrochemical redox behaviors were investigated by cyclic voltammetry and the potentiostatic method. A poly(3-n-octyloxythiophene) film that was deposited on a platinum electrode was found to exhibit electrochromic behaviors, and it switched electrochemically between blue–green oxidized and dark red reduced states. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

白云鄂博主矿开拓运输工艺转换有关问题的探讨

本文对白云鄂博主矿采场铁公路联合运输向公路运输转换位置是否确定为1638m水平以及运输工艺转换过程中相关问题进行分析论证，提出主矿采场铁路至少可向下延深一个水平，技术上可行，节约运费千万元以上。     

On the effectiveness of early life cycle defect prediction with Bayesian Nets

Standard practice in building models in software engineering normally involves three steps: collecting domain knowledge (previous results, expert knowledge); building a skeleton of the model based on step 1 including as yet unknown parameters; estimating the model parameters using historical data. Our experience shows that it is extremely difficult to obtain reliable data of the required granularity, or of the required volume with which we could later generalize our conclusions. Therefore, in searching for a method for building a model we cannot consider methods requiring large volumes of data. This paper discusses an experiment to develop a causal model (Bayesian net) for predicting the number of residual defects that are likely to be found during independent testing or operational usage. The approach supports (1) and (2), does not require (3), yet still makes accurate defect predictions (an R ² of 0.93 between predicted and actual defects). Since our method does not require detailed domain knowledge it can be applied very early in the process life cycle. The model incorporates a set of quantitative and qualitative factors describing a project and its development process, which are inputs to the model. The model variables, as well as the relationships between them, were identified as part of a major collaborative project. A dataset, elicited from 31 completed software projects in the consumer electronics industry, was gathered using a questionnaire distributed to managers of recent projects. We used this dataset to validate the model by analyzing several popular evaluation measures (R ², measures based on the relative error and Pred). The validation results also confirm the need for using the qualitative factors in the model. The dataset may be of interest to other researchers evaluating models with similar aims. Based on some typical scenarios we demonstrate how the model can be used for better decision support in operational environments. We also performed sensitivity analysis in which we identified the most influential variables on the number of residual defects. This showed that the project size, scale of distributed communication and the project complexity cause the most of variation in number of defects in our model. We make both the dataset and causal model available for research use.     

Design of nonlinear controllers for active vehicle suspension with state constraints

Design of active vehicle suspension has tradeoffs between three main performance metrics (passenger comfort, suspension deflection and road holding ability). It has been known that each performance can be achieved by H _∞ controller and they can be gathered by LPV (Linear Parameter Varying) method. However, because the suspension deflection limit was not explicitly considered, this limit may be exceeded. In this paper, the authors propose a “reference shaping“ based method in order to improve the control performance. In this approach, a “virtual reference” signal is imposed to the system such that the suspension deflection is kept small. The effectiveness of the approach is examined by numerical simulations. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008