Extending transmission bandwidth of air-core photonic bandgap fibers

Air-core photonic bandgap fibers offer many unique properties and are critical to many emerging applications. A notable property is the high nonlinear threshold which provides a foundation for applications at high peak powers. The strong interaction of light and air is also essential for a number of emerging applications, especially those based on nonlinear interactions and spectroscopy. For many of those applications, much wider transmission bandwidths are desired to accommodate a wider tuning range or the large number of optical wavelengths involved. Presently, air-core photonic bandgap fibers have a cladding of hexagonal lattice. The densely packed geometry of hexagonal stacking does not allow large nodes in the cladding, which would provide a further increase of photonic bandgaps. On the other hand, a photonic cladding with a square lattice can potentially provide much larger nodes and consequently wider bandgap. In this work, the potentials of much wider bandgap with square lattice cladding is theoretically studied and experimentally demonstrated.     

Evaluation and Optimization of Preparative Variables for Controlled-Release Floatable Microspheres Prepared by Poor Solvent Addition Method

The aim of this study was to evaluate and optimize preparative parameters for floatable theophylline microspheres prepared by the emulsion–solvent evaporation method. A three-factor three-level Box–Behnken design was employed using amount of poor solvent, temperature-increase rate and drug loading as independent factors, and percentage floating at 3 h and time required for 50% drug release as dependent variables. Simultaneous optimization of the parameters for maximum buoyancy and desirable drug release was conducted using a partitioned artificial neural network. A microsphere using 27.6% of drug loading, 0.29°C/min of temperature-increase rate, and 1.7 mL of poor solvent was identified for maximizing buoyancy and sustaining drug release.     

Environmental isolation of Cryptococcus neoformans from an endemic region of HIV-associated cryptococcosis in Thailand

We successfully isolated Cryptococcus neoformans from chicken faeces in suburban areas of Thailand. C. neoformans was isolated from 36/150 houses (24.0%) in the dry season and 6/150 (4.0%) in the rainy season. All environmental isolates were of serotype A. The high isolation rate of 24% from chicken faeces has never been reported previously. Our environmental study could probably explain the high incidence of cryptococcal meningitis in HIV patients in Thailand.     

Multijunction thermal converter with improved frequency characteristics between 10 Hz and 1 MHz

A new multijunction thermal converter (MJTC) for precision AC–DC transfer standard has been developed. A U‐shaped heater pattern was sputter‐deposited onto an AlN plate in order to reduce thermoelectric effect, which causes the frequency‐independent AC–DC transfer difference. Both low‐frequency and high‐frequency characteristics improved as a result of the new configuration, and the AC–DC transfer difference of the MJTC was evaluated to be <1 µV/V between 10 Hz and 100 kHz and <10 µV/V up to 1 MHz. © 2012 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Reliability assessment based on hazard rate model for an embedded OSS porting‐phase

Embedded Open Source Software (OSS) systems have been gaining a lot of attention in the embedded system area. The successful experience of embedded OSSs include Android, BusyBox, TRON, etc. Also, OSS market will be expanded not only to mobile phone OSS areas but also to other embedded OSS areas in the future. However, the poor handling of quality problem and customer support prohibit the progress of embedded OSS. Also, it is difficult for developers to assess the reliability and portability of embedded OSS on a single‐board computer. A method of software reliability assessment based on flexible hazard rate modeling for the embedded OSS is proposed in this paper. Also, several numerical examples are shown by using actual data. Moreover, this paper compares the proposed model with the conventional hazard rate models by using the comparison criteria of goodness‐of‐fit. Copyright © 2011 John Wiley & Sons, Ltd.     

纯铁、铝镇静钢和钛镇静钢的界面特性机理

为了解铝和钛的氧化物在钢中的行为及其夹杂物的去除方法,采用静滴法在1873K及不同氧分压条件下,测定了纯铁、铝镇静钢和钛镇静钢在Al2O3和MgO垫片上的接触角,确认了液滴尺寸与接触角的关系及影响界面张力的因素,并提出了界面行为中线能量的重要性。     

Development of a new heterojunction structure (ACJ -HIT) and its application to polycrystalline silicon solar cells

A new solar cell structure named HIT (Heterojunction with Intrinsic Thin layer) has been developed based on new artificially constructed junction (ACJ) technology. In this structure a non-doped a-Si thin layer was inserted between the p(a-Si)/n(c-Si) heterojunction, improving the output characteristics and achieving a conversion efficiency of 18.1%. This structure was applied to cast polycrystalline silicon solar cells of a practical size. A high conversion efficeincy of 13.6% was obtained with a cell size of 10 cm × 10 cm using various technologies, including hydrogen plasma passivation.     

Effect of overhead ground wires on reduction of failure rates of surge arresters on power distribution lines

Surge arresters are sometimes damaged by lightning strokes with high energy, in spite of installation of conventional protection methods. In order to reduce the number of failures of surge arresters, we should consider another protection method, such as an increase in the withstand capability of surge arresters and installation of additional overhead ground wires. However, quantitative comparison of these methods for preventing damage to surge arresters against lightning strokes with high energy has never been performed. This paper describes the effects of additional overhead ground wires for preventing damage to surge arresters. The main results are: (1) The failure rate of surge arresters on a distribution line with two overhead ground wires is about one third of that with an overhead ground wire. (2) Installation of a second overhead ground wire six to eight spans from the end of a line reduces the failure rate of a surge arrester at the end as effectively as increasing the withstand capability by a factor of two. © 1998 Scripta Technica. Electr Eng Jpn, 122(2): 12–20, 1998     

X-ray Diffraction Analysis to Explore Molecular Traces of Eccentric Contraction on Rat Skeletal Muscle Parallelly Evaluated with Signal Protein Phosphorylation Levels

We performed X-ray diffraction analyses on rat plantaris muscle to determine if there are strain-specific structural changes at the molecular level after eccentric contraction (ECC). ECC was elicited in situ by supramaximal electrical stimulation through the tibial nerve. One hour after a series of ECC sessions, the structural changes that remained in the sarcomere were evaluated using X-ray diffraction. Proteins involved in cell signaling pathways in the muscle were also examined. ECC elicited by 100, 75, and 50 Hz stimulation respectively developed peak tension of 1.34, 1.12 and 0.79 times the isometric maximal tetanus tension. The series of ECC sessions phosphorylated the forkhead box O proteins (FoxO) in a tension-time integral-dependent manner, as well as phosphorylated the mitogen-activated protein kinases (MAPK) and a protein in the mammalian target of rapamycin (mTOR) pathway in a maximal tension dependent manner. Compared to isometric contractions, ECC was more efficient in phosphorylating the signaling proteins. X-ray diffraction revealed that the myofilament lattice was preserved even after intense ECC stimulation at 100 Hz. Additionally, ECC < 75 Hz preserved the molecular alignment of myoproteins along the myofilaments, while 75-Hz stimulation induced a slight but significant decrease in the intensity of meridional troponin reflection at 1/38 nm⁻¹, and of myosin reflection at 1/14.4 nm⁻¹. These two reflections demonstrated no appreciable decrease with triple repetitions of the standard series of ECC sessions at 50 Hz, suggesting that the intensity decrease depended on the instantaneous maximal tension development rather than the total load of contraction, and was more likely linked with the phosphorylation of MAPK and mTOR signaling proteins.     

Implementation of vibration suppression control on FWL processor

In motion or process control systems, a variety of design techniques have been proposed because of the demand for high performance. The higher performance we demand, the higher the degree of the controller becomes. The controller is generally designed by a CAD system and implemented with a microprocessor. But the microprocessor does not have enough precision to realize the results of design by the CAD system. Therefore, the system performance is degraded by finite word length (FWL) effects. To deal with FWL problems, many design methods have been considered in the signal processing field, and high‐ordered digital filters are often used. Among these methods, the implementation technique based on the state‐space realization can minimize the sensitivity to perturbation of coefficients. Noting that optimal realizations with the same transfer function are unique only up to an orthogonal similarity transformation, we must choose the realization within this class of optimal realizations. In this paper, we present an algorithm to find a state‐space realization which minimizes the frequency‐weighted sensitivity measure of the controller performance. Furthermore, we present some experimental results to verify the effectiveness of the proposed algorithm. © 1999 Scripta Technica, Electr Eng Jpn, 128(1): 45–52, 1999