Magnetic anisotropy of Co-Cr thin films as a function of substrate temperature during deposition

A sequence of Co78Cr22films, 500 nm in thickness, was prepared by deposition on glass in a modified Varian D.C. magnetron S-gun sputtering system. The substrate temperature during deposition, Ts, was fixed at various values with an upper limit of 300°C. Specimens were examined by VSM, TM, FMR and TEM. Msrises significantly with increasing Ts, peaking at 200°C at 370 emu/cm³. The effective volume-averaged anisotropy drops for Ts>110°C from +1.6 KOe to progressively negative values (-4.3 KOe at 300°C). From FMR we find indications of the presence, in addition to the transition and bulk layers, of a highly negative anisotropy constituent (sim-11.5KOe anisotropy field). This resonance appears at Tsvalues of 150°C and above. TEM plane and cross-section views taken on a Ts= 150°C specimen show islands composed of tilted columns within the bulk. For vertical recording, specimens prepared at Tsvalues between 50 and 100°C are recommended. On the other hand, for longitudinal recording applications, films prepared at Tsvalues above 250°C would seem to be appropriate.     

Predicting the performance of concrete structures exposed to chemically aggressive environment—Field validation

The behavior of two series of concrete slabs exposed to sulfate-bearing soils was investigated by a numerical model called STADIUM. In addition to the diffusion of ions and moisture, the model also accounts for the effects of dissolution/precipitation reactions on the transport mechanisms. The simulations yielded by the model were compared to the actual degradation of the slabs after 8 years of exposure. The microstructural alterations of concrete resulting from the penetration of magnesium, chloride and sulfate ions were studied by backscatter mode scanning electron microscope observations and energy-dispersive X-ray analyses. The comparison of both series of data indicates that the model can reliably predict the various features of the microstructural alterations of concrete.

---

Résumé Le comportement de deux séries de dalles sur sol en béton exposées à des sols chimiquement agressifs a été étudié à l'aide d'un code de calcul numérique appelé STADIUM. Ce modèle permet de décrire le transport couplé de l'eau et des ions dans des matériaux poreux non-saturés en prenant en considération l'influence des réactions chimiques. Les résultats des simultations de la dégradation du béton après huit ans d'exposition à des ions chlore, sulfate et magnésium. Les observations ont été réalisées par microscopie électronique à balayage. Des analyses par dispersion des rayons X ont également été effectuées. Les données démontrent clairement que le modèle perment de prédire avec précision le comportement du béton soumis à différents types d'agression chimique.

---

---

Editorial Note Laval University (Canada) is a RILEM Titular Member. Prof. J. Marchand was awarded the 2000 Robert L'Hermite Medal. He is Editor in Chief for Concrete Science and Engineering and Associate Editor for Materials and Structures. He participates in RILEM TC 186-ISA ‘Internal Sulfate attack’.     

NO emission characteristics in counterflow diffusion flame of blended fuel of H2/CO2/Ar

Flame structure and NO emission characteristics in counterflow diffusion flame of blended fuel of H₂/CO₂/Ar have been numerically simulated with detailed chemistry. The combination of H₂, CO₂ and Ar as fuel is selected to clearly display the contribution of hydrocarbon products to flame structure and NO emission characteristics due to the breakdown of CO₂. A radiative heat loss term is involved to correctly describe the flame dynamics especially at low strain rates. The detailed chemistry adopts the reaction mechanism of GRI 2.11, which consists of 49 species and 279 elementary reactions. All mechanisms including thermal, NO₂, N₂O and Fenimore are taken into account to separately evaluate the effects of CO₂ addition on NO emission characteristics. The increase of added CO₂ quantity causes flame temperature to fall since at high strain rates a diluent effect is prevailing and at low strain rates the breakdown of CO₂ produces relatively populous hydrocarbon products and thus the existence of hydrocarbon products inhibits chain branching. It is also found that the contribution of NO production by N₂O and NO₂ mechanisms are negligible and that thermal mechanism is concentrated on only the reaction zone. As strain rate and CO₂ quantity increase, NO production is remarkably augmented. Copyright © 2002 John Wiley & Sons, Ltd.     

A compact LTCC-based Ku-band transmitter module

Presents design, implementation, and measurement of a three-dimensional (3-D)-deployed RF front-end system-on-package (SOP) in a standard multi-layer low temperature co-fired ceramic (LTCC) technology. A compact 14 GHz GaAs MESFET-based transmitter module integrated with an embedded bandpass filter was built on LTCC 951AT tapes. The up-converter MMIC integrated with a voltage controlled oscillator (VCO) exhibits a measured up-conversion gain of 15 dB and an IIP3 of 15 dBm, while the power amplifier (PA) MMIC shows a measured gain of 31 dB and a 1-dB compression output power of 26 dBm at 14 GHz. Both MMICs were integrated on a compact LTCC module where an embedded front-end band pass filter (BPF) with a measured insertion loss of 3 dB at 14.25 GHz was integrated. The transmitter module is compact in size (400 /spl times/ 310 /spl times/ 35.2 mil/sup 3/), however it demonstrated an overall up-conversion gain of 41 dB, and available data rate of 32 Mbps with adjacent channel power ratio (ACPR) of 42 dB. These results suggest the feasibility of building highly SOP integrated RF front ends for microwave and millimeter wave applications.     

千米桥东潜山天然气地球化学特征及成因探索

通过地化分析，结合地质条件等，对千米桥东潜山天然气地球化学特征进行了剖析，并对其气藏的形成进行了探索，结果认为：千米桥东潜山天然气为无机二氧化碳、偏腐殖型有机气，腐泥型有机气的复合气，主源为东部歧口凹陷沿岩带深层（偏）腐殖型气，烃类气体聚集时间晚，为更新世明化镇沉积时其，而无机二氧化碳聚集时间早于烃类气体；与千米桥凝析气藏不同的是该气藏CO2含量高。     

The Distribution of Active ingredients in Supported Catalysts Prepared by Impregnation

Supported catalysts, one of the commonest forms of heterogeneous catalysts in practical use, consist of small crystallites of a catalytically active component dispersed in a porous support of high surface area. Impregnation of the support with an aqueous solution of a compound containing the appropriate catalytic component is an important and frequently used method of preparing this type of catalyst. A nonaqueous solution should be used if the sup port surface is hydrophobic or if hydrolysis of the support surface is to be avoided. In its simplest form, this impregnation method involves three steps: (1) contacting the support with impregnating solution for a certain period of time, (2) drying the support to remove the imbibed liquid, and (3) activating the catalyst by calcination, reduction, or other appropriate treatment.     

Evaluating and monitoring nucleation and growth in copper foil

The electrodeposition of copper foil for use in electronic materials applications is a complex and demanding process. The specific aspects of producing and controlling the structure-property-performance requirements of the foil are important because of the stringent demands placed on their use in printed circuit boards and similar products. In this paper, a brief review of the electrodeposition process for raw copper foil is presented. Since electrolyte additives play such a significant role in the copper-depositionprocess, the effects of two essential additives, chloride ion and an organic (e.g., glue or gelatine), on the foil are described. Also, the influence of other operating parameters on the initial nucleation, growth, and subsequent electrocrystallization are discussed. Selected characterization methods, such as polarization and scanning electron micrography techniques, are described as a means of monitoring the process, but universally accepted methods of evaluating and controlling the additives and foil quality during electrolysis are still being sought.     

Effect of microporosity on tensile properties of as-cast AZ91D magnesium alloy

In the present study, the effect of microporosity on the tensile properties of as-cast AZ91D magnesium alloy was investigated through experimental observation and numerical prediction. The test specimens were fabricated by die-casting and gravity-casting. For gravity-casting, the inoculation and use of various metallic moulds were applied to obtain a wide range of microporosity. The deficiency of the interdendritic feeding of the liquid phase acted as a dominant mechanism on the formation of the micropores in the Mg?Al-alloys, rather than the evolution of hydrogen gas. Although tensile strength and elongation has a nonlinear and very intensive dependence upon microporosity, the yield strength appeared to have a linear relationship with microporosity. However, it was possible to quantitatively estimate the linear contribution of microporosity on the individual tensile property for a range of microporosity, which was below about 1%. The numerical prediction suggests that the effect of microporosity on fractured strength and elongation decreased as the strain hardening exponent increased. Furthermore, the shape and distribution of micropores may play a more dominant role than local plastic deformation on the tensile behavior of AZ91D alloy.     

超声波处理和染料结晶性能对粒度分布的影响

超声波是一种频率超越人类听觉范围的声波 ,主要分为动力超声波 ( 1 8ｋＨｚ～ 1ＭＨｚ)和用于诊断的超声波 ( 1ＭＨｚ以上 )。多年以来 ,超声波作为一种辅助工具广泛应用于许多领域 ,从而引起了化学家的极大兴趣。研究表明 ,在纺织品染色过程中 ,超声波能提高反应速率可能归因于超声波的能量 ,有关超声波的应用潜力已有许多文献报道。超声波能提高染色效率主要归因于液体介质中的空化现象 ,这一点已被一致认可。所谓空化现象是指微气泡增长、崩溃、爆炸。Ｍａｓｏｎ指出 ,经超声波辐射的固体粒度显著减小。Ｔｏｍｌｉｓｏｍ和其他工作者也…