Measuring the concentrations of drinking water disinfection by-products using capillary membrane sampling-flow injection analysis

A capillary membrane sampling-flow injection analysis method is presented for selectively measuring the concentrations of total trihalomethanes (THMs) and total haloacetic acids (HAAs) in drinking water. The method is based on the reaction between nicotinamide and THM or HAA species to yield a fluorescent product. Two configurations are presented, one selective for total THMs and another selective for total HAAs. The construction of a capillary membrane sampler is described, and the results of method detection limit, accuracy and precision studies are reported for each method. Interference, selectivity and linearity studies are reported as well as the effect of temperature and ionic strength changes. Drinking water samples were analyzed by each proposed method and the results were compared to USEPA methods 502.2 and 552.3.     

Morphology study of progesterone polymorphs prepared by polymer‐induced heteronucleation (PIHn)

In this article, morphology of progesterone polymorphs prepared by polymer‐induced heteronucleation (PIHn) technique was studied. Hydroxypropyl methylcellulose(HPMC), such as dextran T‐500 and gelatin G‐9382, polyisoprene (PI), and acrylonitrile/butadiene copolymer (NBR) were used as substrates. The crystallizations were performed by solvent evaporation at room temperature from 0.5, 10, and 40 mg/ml solutions in chloroform and acetone. Progesterone polymorphs were identified by X‐ray diffraction. Differential scanning calorimetry and total attenuated reflectance infrared spectroscopy were used as complementary techniques in the identification. Depending on the polymeric matrix and the concentration used, form 1, form 2, or mixture of both polymorphs were obtained. Scanning electron microscopy pictures evidenced difference in morphology and in homogeneity of the two progesterone polymorphs. These polymorphs prepared by PIHn, did not present a distinctive morphology that allows identifying polymorph by its crystal habit. Hence, polymeric matrix induced the crystallization, affecting polymorphism and morphology. SCANNING 35:213‐221, 2013. © 2012 Wiley Periodicals, Inc.     

Determination of the Hydroxyl Value of Soybean Polyol by Attenuated Total Reflectance/Fourier Transform Infrared Spectroscopy

A rapid method for the quantitative determination of the hydroxyl value (OHV) of hydroxylated soybean oils by HATR/FTIR spectroscopy is described. Calibration standards were prepared by the formic acid/hydrogen peroxide method and OH values were determined by the official method of AOCS Tx 1a-66, covering an analytical range of 3.5–125 mg of KOH/g of sample. A partial least squares (PLS) calibration model for the prediction of the hydroxyl value (OHV) was developed based on eight different spectral subregions between 3,150 and 990 cm⁻¹ and combinations of them. On average, 36 samples were used for the modeling and 17 were used for external validation. The resulting calibration was linear over the analytical range and had a standard deviation of 2.334. Validation of the method was carried out by comparing the OHV of a series of hydroxylated soybean oils predicted by the PLS model to the values obtained by the AOCS standard method. A correlation coefficient of R ² = 0.9843 and RMSEC and RMSEP values of, respectively, 3.393 and 3.643 were obtained. After the calibration of the spectrometer, the OHV could be obtained in 2–3 min per sample, a major improvement over conventional wet chemical methods. The advantages of these methodologies are that they do not destroy the sample, have a lower cost, expedite the analysis and do not produce residues. Therefore, they may yield excellent results when used to quantify OHV of soybean polyols obtained by hydroxylation reaction.     

Formulating a low-alkalinity, high-resistance and low-heat concrete for radioactive waste repositories

Investigations were carried out in order to formulate and characterize low-alkalinity and low-heat cements which would be compatible with an underground waste repository environment. Several systems comprising Ordinary Portland Cement (OPC), a fast-reacting pozzolan (silica fume (SF) or metakaolin (MK)) and, in some cases, a slow-reacting product (fly ash (FA) or blastfurnace slag (BFS)) were compared. Promising results were obtained with some binary mixtures of OPC and SF, and with some ternary blends of OPC, SF and FA or BFS: pH of water in equilibrium with the fully hydrated cements dropped below 11. Dependence of the properties of standard mortars on the high contents of FA and SF in the low-pH blends was examined. Combining SF and FA seemed attractive since SF compensated for the low reactivity of FA, while FA allowed to reduce the water demand, and dimensional variations of the mortars. Finally, low-heat (ΔT < 20 °C under semi-adiabatic conditions) and high strength (≈ 70–80 MPa) concretes were prepared from two low-pH cements: a binary blend made from 60% of OPC and 40% of SF, and a ternary blend including 37.5% OPC, 32.5% SF and 30% FA.     

Role of anionic and nonionic surfactants on the control of particle size and latex colloidal stability in the seeded emulsion polymerization of butyl methacrylate

The evolution of the main colloidal parameters in the seeded starved‐feed semi‐continuous emulsion polymerization of butyl methacrylate (BMA) was investigated, with the main purpose of assessing the effectiveness of the semi‐empirical relationship S = K · S_S · ΔA/A_S as a tool to define the surfactant/monomer feed ratio (∝ K) best suited to achieve a target particle size. In particular, the effect of the type and amount of surfactant [i.e., anionic, sodium dodecyl sulfate (SDS), or nonionic, Brij 58P] added during the semi‐continuous stage was considered. Coagulum formation was never observed under the adopted experimental conditions. To detect the occurrence of secondary nucleation or particle aggregation, or both, the particle size and number of particles, the surface tension and the particle surface coverage ratio were correlated. The best results were obtained with SDS and 0.8 ≤ K ≤ 3. In fact, under the selected experimental conditions, only with SDS did the number of particles remain nearly constant throughout the polymerization at the value defined by the seed latex; the particle size distribution was highly monodisperse, and the final particle diameter closely matched the calculated one (～ 120 nm). The above semi‐empirical relationship based on the adjustable parameter K was validated by running test polymerizations aimed at lattices with well‐defined particle size. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3083–3094, 2006     

Characterization of sulfonated poly(styrene–divinylbenzene) and poly(divinylbenzene) and its application as catalysts in esterification reaction

Polymeric supports based on divinylbenzene (DVB) were prepared by aqueous suspension polymerization in presence or absence of styrene (S), using toluene and n‐heptane as diluents of the monomers. Poly(S–DVB) and poly(DVB) were sulfonated with sulfuric acid in presence of 1,2‐dichloroethane. The influence of the morphological structure of the supports and as a consequence of the catalyst on the esterification reaction of acetic acid with n‐butanol was evaluated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3616–3627, 2006     

The calculation of the heat release rate by oxygen consumption in a controlled‐atmosphere cone calorimeter

The standard cone calorimeter according to ASTM E 1354 and ISO 5660 enables reaction‐to‐fire tests to be performed in ambient atmospheric conditions. A controlled‐atmosphere chamber modifies the standard apparatus in a way that allows tests to be performed in nonambient conditions as well. The enclosed chamber is placed underneath the standard exhaust hood and does not have a closed connection to the hood. With this open arrangement, the exhaust gases are diluted by excess air drawn in from the laboratory surroundings. Heat‐induced changes in the consequential dilution ratio affect the calculation of fire quantities and, when neglected, lead to deviations of up to 30% in heat release rate. The paper introduces a test protocol and equations to calculate the heat release rate taking dilution effects into account. A mathematical correction is shown that compensates for the dilution effects while avoiding extensive mechanical changes in the equipment. Copyright © 2013 John Wiley & Sons, Ltd.     

New carbon composite adsorbents for the removal of textile dyes from aqueous solutions: Kinetic,equilibrium, and thermodynamic studies

New carbon composite materials were prepared by pyrolysis of mixture of coffee wastes and red mud at 700 °C with the inorganic: organic ratios of 1.9 (CC-1.9) and 2.2 (CC-2.2). These adsorbents were used to remove reactive orange 16 (RO-16) and reactive red 120 (RR-120) textile dyes from aqueous solution. The CC-1.9 and CC-2.2 materials were characterized using Fourier transform infrared spectroscopy, Nitrogen adsorption/desorption curves, scanning electron Microscopy and X-ray diffraction. The kinetic of adsorption data was fitted by general order kinetic model. A three-parameter isotherm model, Liu isotherm model, gave the best fit of the equilibrium data (298 to 323 K). The maximum amounts of dyes removed at 323 K were 144.8 (CC-1.9) and 139.5 mg g^?1 (CC-2.2) for RO-16 dye and 95.76 (CC-1.9) and 93.80 mg g^?1 (CC-2.2) for RR-120 dye. Two simulated dyehouse effluents were used to investigate the application of the adsorbents for effluent treatment.