Photocatalytic oxidation of low concentration 2,4-D solution with new TiO2 fiber catalyst in a continuous flow reactor.

Environmental pollution by low concentrations of 2,4-Dichlorophenoxyacetic acid (2,4-D) is a concern these days due to ever increasingly stringent regulations. Photocatalysis with immobilized TiO2 fiber is a promising oxidation method. Laboratory experiments on photocatalytic degradation of 0.045 mmol l(-1) 2,4-D with the world's first high-strength TiO2 fiber catalyst were carried out in a continuous flow reactor in which the degradations were, in general, similar to those with high 2,4-D concentrations investigated elsewhere. Degradation and mineralization of 2,4-D were significantly enhanced with no initial pH adjustments. The rate constants for total organic carbon (TOC) without pH adjustment were about two-fold bigger than the pH adjustment cases. CO2 gas measurement and carbon mass-balance were carried out for the first time, where about 34% organic carbon converted into CO2 gas during four-hour oxidation. 2,4-Dichlorophenol (2,4-DCP), phenol, benzyl alcohol and two unknowns (RT = 2.65 and 3.78 min.) were detected as aromatic intermediates while Phenol was the new aromatic in HPLC analysis. Dechlorination efficiencies were high (> 70%) in all the cases, and more than 90% efficiencies were observed in chloride mass balance. Bigger flow rates and solution temperature fixed at 20 degrees C without pH adjustment greatly enhanced 2,4-D mineralization. These results can be an important basis in applying the treatment method for dioxin-contaminated water and wastewater.     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results

Conical picks are the essential cutting tools used especially on roadheaders, continuous miners and shearers and their cutting performance affects directly the efficiency and the cost of rock/mineral excavation. In this study, in order to better understand the effects of dominant rock properties on cutter performance, 22 different rock specimens having compressive strength values varying from 10 to 170 MPa are first subjected to a wide range of mechanical tests. Then, laboratory full-scale linear cutting tests with different depth of cut and cutter spacing values are realized on large blocks of rock specimens using one type of conical pick. Specific energy, cutting and normal force values for relieved and unrelieved cutting modes are recorded using a triaxial force dynamometer with capacity of 50 tonnes and a data acquisition system. Cutter force and specific energy values are correlated with rock properties and theoretical force and specific energy values obtained from widely used theoretical approaches.The results indicate that uniaxial compressive strength among the rock properties investigated is best correlated with the measured cutter performance values, which is in good agreement with previous studies. However, it is also emphasized in this study that Brazilian tensile strength, Schmidt hammer rebound values, static and dynamic elasticity modulus are also dominant rock properties affecting cutter performance.Theoretical specific energy defined by different researchers has a meaningful relationship with the experimental specific energy, which is an essential parameter for predicting the instantaneous cutting rates of mechanical excavation systems. It is also demonstrated that the experimental cutter forces obtained for 5 mm depth of cut are in good agreement with theoretical force values, if the friction angle between rock and cutting tool is included in the theoretical formulation. It is emphasized that, to some extend, laboratory tests can help to minimize high cost of a trial–error approach in the field.     

Tri-axial sensors and actuators made of a single piezoelectric cylindrical shell

Electromechanical transducers for sensing and actuating disturbances or vibrations have been used in many fields of applications. There have been transducers of different configuration developed for the unidirectional transduction. This paper demonstrates a single element transducer for tri-axial components made of a piezoelectric cylindrical shell. The separation of the tri-axial transductions is achieved by devising a proper electrode arrangement. The structure and the fundamental idea are first presented, and then the numerical analysis by means of the finite element modeling follows, and their characteristics and behaviors are then experimentally verified.     

A high-performance multichannel dual-gate poly-Si TFT fabricated by excimer laser irradiation on a floating a-Si thin film

A new excimer laser annealing (ELA) process that uses a floating amorphous-Silicon (a-Si) thin film with a multichannel structure is proposed for high-performance poly-Si thin-film transistors (TFTs). The proposed ELA method produces two-dimensional (2-D) grain growth, which can result in a high-quality grain structure. The dual-gate structure was employed to eliminate the grain boundaries perpendicular to the current flow in the channel. A multichannel structure was adapted in order to arrange the grain boundary to be parallel to the current flow. The proposed poly-Si TFT exhibits high-performance electrical characteristics, which are a high mobility of 504 cm/sup 2//Vsec and a low subthreshold slope of 0.337 V/dec.     

Catalytic aminolysis of epoxide by alumina prepared from amine-protected Al precursor

The catalytic activities of alumina prepared from an Al alkoxide-amine adduct monomer for the reaction of cyclopentene oxide with piperidine was determined after various pretreatments, including calcination and exposure to moisture. They were compared with the activity of alumina prepared by the conventional hydrolysis method. It was found that the as-prepared sample from the alkoxide-amine monomer preparation was five times more active than a conventional preparation, suggesting that it has a higher density of surface Lewis acid sites. However, its activity was much more severely suppressed by exposure to moisture.     

On Faster I DDQ Measurements

The purpose of this paper is to introduce a new I _DDQ measurement technique based on active successive approximations, called ASA-I _DDQ. This technique has unique features facilitating a speed-up in I _DDQ measurement. Experimental results suggest that a significant speed-up factor (up to 4) can be obtained over the QuiC-Mon technique. Such a speed-up is a key element in the replacement of single-threshold I _DDQ testing since it amplifies the effectiveness of post-processing techniques.     

Formulation of a ceramic ink for a wide-array drop-on-demand ink-jet printer

This paper describes the methodology for simulating a reprographic ink with a ceramic ink based on a commercially available zirconia powder for direct ceramic ink-jet printing. Of over-riding importance was matching viscosity and this was tested systematically by using a mineral oil–hexane binary system. Of secondary importance was adjustment of the pressure defect behind the nozzle to compensate for small differences in surface tension. The inks tested in the wide array print-head were based on low electrical conductivity liquids to avoid damage to the electroding system. The organic binder for the zirconia ink was paraffin wax and the dispersant was a hydroxystearic acid based polyester.