Power sector development in India with CO2 emission targets: Effects of regional grid integration and the role of clean technologies

The power sector in India at present comprises of five separate regional electricity grids having practically no integrated operation in between them. This study analyses the utility planning, environmental and economical effects of integrated power sector development at the national level in which the regional electric grids are developed and operated as one integrated system. It also examines the effects of selected CO₂ emission reduction targets in the power sector and the role of renewable power generation technologies in India. The study shows that the integrated development and operation of the power system at the national level would reduce the total cost including fuel cost by 4912 million $, total capacity addition by 2784 MW, while the emission of CO₂, SO₂ and NO_x would be reduced by 231.6 (1.9%), 0.8 (0.9%), 0.4 (1.2%) million tons, respectively, during the planning horizon. Furthermore, the study shows that the expected unserved energy, one of the indices of generation system reliability, would decrease to 26 GWh under integrated national power system from 5158 GWh. As different levels of CO₂ emission reduction targets were imposed, there is a switching of generation from conventional coal plants to gas fired plants, clean coal technologies and nuclear based plants. As a result the capacity expansion cost has increased. It was found that wind power plant is most attractive and economical in the Indian perspective among the renewable options considered (Solar, wind and biomass). Copyright © 2003 John Wiley & Sons, Ltd.     

下T6-361井多井防碰绕障技术

下T6—361井是一口双靶定向井，由于受地面和地质条件的限制，必须穿越9口井，其中最近的4口井防碰距仅为13—32m，钻井施工难度大，是一口较典型的多井防碰绕障定向井。在优化井身剖面设计、优选钻具组合、采用导向钻井技术的基础上，采取了一系列安全钻进措施，顺利钻至设计井深。对该井的地质工程设计、井眼轨迹控制及防碰绕障技术等进行了介绍，对同类型井的施工有一定的借鉴。     

Microstructure and fatigue properties of hydroformed aluminum alloys 6063 and 5754

This study investigated the microstructure and fatigue properties of hydroformed sections of the 5754 and 6063 aluminum alloys. The second-phase particles in 6063-T7 are identified as a mixture of Al₁₂Fe₃Si and Al₉Fe₂Si₂, with a slightly higher fraction of the former. The constituent particles in the 5754 alloy are Al₄Mn-type hexagonal compounds, where Mn is partially substituted by various other elements, resulting in Al₄(Fe,Mn,Si,Cr). The results show that despite its lower yield strength, the hydroformed 5754 alloy has higher ultimate tensile strength, ductility, and, more importantly, higher fatigue resistance than the 6063 material. Both crystallographic stage I and noncrystallographic stage II cracking are found in the 6063-T7 samples, but only stage II cracking is observed in the 5754 alloy. This implies that the low fatigue strength of 6063-T7 is related to its relatively large grain size, resulting in rapid stage I crack propagation. The higher fatigue lives of the 5754 alloy compared to the 6063 alloy in both the low- and high-cycle life regimes are due to the increased fatigue-crack-initiation and propagation resistance of the 5754 alloy and its probable cyclic strain-hardening behavior.     

Optimal and reinforced robustness designs of fuzzy variable structure tracking control for a piezoelectric actuator system

In this paper, a piezoelectric actuator (PEA) system is approximated by N subsystems, which are described by pulse transfer functions. The approximation error between the PEA system and the fuzzy linear pulse transfer function system is represented by additive nonlinear time-varying uncertainties in every subsystem. First, a dead-beat to the switching surface for every ideal subsystem is designed. It is called the "variable structure tracking control". The output disturbance of the ith subsystem is caused by the approximation error of fuzzy-model and the interaction dynamics resulting from other subsystems. In general, it is not small. Then, the H/sup /spl infin//-norm of the sensitivity function between the switching surface and the output disturbance is minimized. It is the "optimal robustness". Although the effect of the output disturbance is attenuated, a better performance can be reinforced by a switching control which is based on the Lyapunov redesign. This is the final step for the robustness design of control, which is "reinforced robustness". The stability of the overall system is verified by Lyapunov stability theory. Experimental work of a PEA system was carried out to confirm the validity of the proposed control.     

Axial vibrations of U-shaped bellows with elastically restrained end conditions

Previous work by Li et al. in the area of axial vibrations of bellows dealt with fixed end conditions. However, it is seen on several occasions that bellow ends are welded to a small pipe spool that has a lumped mass such as a valve or an instrument. Hence, the present paper aims at finding out the effect of elastically restrained ends on the axial natural frequencies. The analysis considers finite stiffness axial restraints on the bellows, i.e. solving the set of equations with non-homogeneous boundary conditions. Two bellow specimens are considered for comparison having the same dimensions as taken by Li in his analysis. The transcendental frequency equation deduced is accurate as the first, second and third mode frequencies computed are in close agreement to the ones obtained by Li.     

An order-specific clustering algorithm for the determination of representative demand curves

Data clustering consists of a group of procedures used to collect similar entries or data points within a set into clusters. No existing clustering technique considers entries sequentially in time. In some cases, it is desirable to generate clusters that represent a segment of a time-ordered data set. For these purposes, an order-specific clustering algorithm is proposed. The proposed algorithm employs representative load curves to describe the clusters it generates. The capabilities of the order-specific clustering algorithm are demonstrated on a case study using electricity demand data for the province of Ontario, Canada. Two different applications of the clustering algorithm on this data set are given to demonstrate the effect of error threshold values on the formation of clusters. An analysis of the error for each of these clustering applications is presented.     

Life cycle of hydroprocessing catalysts and total catalyst management

Hydroprocessing catalysts based on Ni, Co, Mo and W are used in various refinery processing applications where several deactivation mechanisms become of importance (coke formation, active phase sintering, metals deposition, poisoning) in the catalyst's life cycle. The life cycle of commercial hydroprocessing catalysts is very complex and includes the catalyst production, sulfidation, use, oxidative regeneration followed by re-sulfidation and reuse or, if reuse is not possible, recycling or disposal. To understand the changes in catalyst properties taking place during a life cycle, the catalyst quality in the different stages can be best monitored by using advanced analytical techniques. The catalyst's life cycle is further complicated by numerous technical, environmental and organizational issues involved. In principle, different companies can be involved in each of the life cycle steps. Leading catalyst manufacturers, together with specialized firms, offer refineries a total catalyst management concept, starting with the purchase of the fresh catalyst and ending with its final recycling or disposal. Total catalyst management includes a broad range of services, ensuring optimal timing during the change-out process, reliable, smooth and safe operations, minimal downtime and maximum catalyst and unit performance.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

汽车漆漆膜质量的改进与提高

通过对车身漆膜质量问题的分析,采取专业清洁公司整体承包车间保洁、工艺方面改进、更换生产外材料、供应商加强对汽车漆使用的监控等一系列措施,漆膜质量水平得以提高.