Nonparametric methods for 1-out-of-2: G repairable systems

The steady state availability of 1-out-of-2 : G repairable system is obtained under the assumption that the life time of a component in standby position follows exponential distribution. It's nonparmetric estimator is proposed. The asymptotic properties of the estimator are used to provide the fixed width coinfience interval with specified coverage probability and testing of hypothesis problem using sequential procedure.     

Investigation on La3+ and Dy3+ co-doped ceria ceramics with an optimized average atomic number of dopants for electrolytes in IT-SOFCs

In the present study, we investigate the fundamental properties of CeO₂ by selecting La³⁺ (57), and Dy³⁺ (66) as dopants with optimized average atomic number of 61.5, which lies in between Pm³⁺ (62) and Sm³⁺ (62) in accordance with the criteria for optimum doping. A system of co-doped ceria ceramics Ce_1–x–yLa_xDy_yO_2-δ ((x, y) = (0.00, 0.00), (0.025, 0.025), (0.05, 0.05), (0.075, 0.075), (0.10, 0.10), (0.00, 0.20) and (0.20, 0.00)) as electrolytes for intermediate temperature solid oxide fuel cells were successfully prepared by a well-known sol-gel auto-combustion route. In order to obtain dense samples, the prepared pellets were sintered in air at 1300 °C for 4 h using conventional furnace and relative densities of all the samples were found to be higher than 95%. Single phase cubic structure, microstructural density and elemental composition analysis of all the samples were studied by powder X-ray diffraction, scanning electron microscope and energy dispersive spectroscopy techniques, respectively. Raman spectroscopy analysis confirmed the formation of concentrated O^2-–vacancies in the co-doped ceria system. Impedance spectroscopy measurements revealed the high value of total ionic conductivity and low activation energy for the composition Ce_0.85La_0.075Dy_0.075O_2?δ i.e., 2.08 × 10^–2 S cm^–1 and 0.58 eV, respectively. Linear thermal expansion analyses of all the samples revealed the matched thermal expansion coefficients. Finally, these results recommend that the Ce_0.85La_0.075Dy_0.075O_2?δ sample can be useful as a solid electrolyte in IT-SOFC applications.     

Analysis of a solar water heating system with n-tanks in series

A straightforward analysis of a solar water heating system with n-tanks connected in series has been presented. The long-term performance of the system has also been studied. On the basis of numerical calculations made for four successive days, the following conclusions have been drawn:

1. (1) The fluctuation in temperature variation decreases with increase of the number of tanks connected in series.

2. (2) The variation becomes smooth after the second successive day, which is more desirable from the point of view of users.

     

Structural and optical properties of Zn3P2 thin films

Conditions have been developed for the deposition of a stoichiometric thin film of zinc phosphide (Zn₃P₂) using electron beam evaporation. Structural properties of as-deposited and annealed thin films of zinc phosphide have been studied using electron and X-ray diffraction. The as-deposited film is non-crystalline, structural ordering starts on annealing at 200° C and the film becomes crystalline at 300° C with the structure matching that of the bulk material. Optical absorption has been investigated over the range 1 to 3 eV with emphasis on the region of interband absorption. The thin film absorption edge is found to be exponential for lower values of absorption coefficient. Analysis of thin film data showed that Zn₃P₂ is a direct-band-gap material. On annealing there is a shift in the band edge towards higher energy. NCL Communication No. 3571.     

Surfactant‐mediated synthesis of polyhydroxybutyrate (PHB) nanoparticles for sustained drug delivery

In this study, polyhydroxybutyrate (PHB) nanoparticles were synthesised following nanoprecipitation method having different solvents and surfactant (Tween 80) concentrations. In this study, PHB nanoparticles were encapsulated with curcumin and subjected for sustained curcumin delivery. Both the curcumin loaded and unloaded PHB nanoparticles were characterised using FTIR, SEM, and AFM. Sizes of the particles were found to be between 60 and 300 nm. The drug encapsulation efficiency and in vitro drug release of the nanoparticles were analysed. Antibacterial activity and anticancer activity were also evaluated. The LC₅₀ values of most of the nanoparticles were found to be between 10 and 20 µg/100 µl, anticancer activity of curcumin loaded PHB nanoparticles were further confirmed by AO/PI staining and mitochondrial depolarisation assay.Inspec keywords: encapsulation, cancer, scanning electron microscopy, nanoparticles, surfactants, drugs, nanofabrication, antibacterial activity, biomedical materials, drug delivery systems, polymers, nanomedicine, Fourier transform infrared spectra, precipitation (physical chemistry), atomic force microscopy, particle sizeOther keywords: surfactant‐mediated synthesis, polyhydroxybutyrate nanoparticles, sustained drug delivery, surfactant concentrations, PHB nanoparticles, sustained curcumin delivery, drug encapsulation efficiency, anticancer activity, in vitro drug release, nanoprecipitation method, Tween 80, FTIR spectra, SEM, AFM, particle sizes, antibacterial activity, AO‐PI staining, mitochondrial depolarisation assay     

Distribution and Prediction of Boundary Shear in Diverging Compound Channels

Measurement of bed shear stress is always a challenging task for engineers. In river engineering, bed shear is a fundamental variable and is important in estimating flow resistance and sediment transport. In this study, experiments are carried out in diverging compound channel with smooth bed (perspex sheet) and rough bed (Gravel) conditions to determine the effect of roughness. The shear velocity is estimated from universal logarithmic law. The effect of geometry and roughness on Von-Karman constant, eddy viscosity coefficient, friction factor is studied. The mass conservation and momentum conservation equations are used to derive apparent shear forces at interface of main channel and floodplain. A genetic algorithm model is developed to predict percentage of shear force (%Sfp) carried by sub-sections. To perform better with less and unseen data K-Fold cross-validation technique is used. The model is compared with available models in literature and it is observed that developed model gave better predictions with low MAPE.

     

Tensile Response of Hoop Reinforced Multiaxially Braided Thin Wall Composite Tubes

This paper presents the tensile response of thin-walled composite tubes with multi-axial fibre architecture. A hybrid braid-wound layup has the potential to optimise the composite tube properties, however, stacking sequence plays a role in the failure mechanism. A braid-winding method has been used to produce stacked overwound braid layup [(±45°/0°)₅/90°₄]_T. Influence of stacking sequence on premature failure of hoop layers has been reported. Under tensile loading, a cross-ply composite tube with the alternate stacking of hoop and axial fibre show hoop plies splitting similar to the overwound braided composite tube. However, splitting has been restricted by the surrounding axial plies and contained between the adjacent axial fibre tows. This observation suggests hoop layers sandwiched between braid layers will improve structural integrity. A near net shape architecture with three fibre orientation in a triaxial braid will provide additional support to prevent extensive damage for plies loaded in off-axis. Several notable observations for relatively open braid structures such as tow scissoring, high Poisson’s ratio and influence of axial tow crimp on the strain to failure have been reported. Digital Image Correlation (DIC) in conjunction with surface strain gauging has been employed to capture the strain pattern.     

Influence of copper substitution on magnetic and electrical properties of MgCuZn ferrite prepared by microwave sintering method

Polycrystalline MgCuZn ferrites with chemical formula Mg_0.50-xCu_xZn_0.50Fe₂O₄ (x = 0.00, 0.05, 0.10, 0.15, 0.20, 0.25 and 0.30) were prepared by microwave sintering method. These powders were calcined, compacted and sintered at 950 °C for 30 min. Structural, microstructural and elemental analyses were carried out using X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometry (EDS), respectively. The lattice parameter is found to increase with increasing copper content. A remarkable densification is observed with the addition of Cu ions in the ferrites. The sintered ferrite was characterized for initial permeability, dielectric constant and dielectric loss tangent and ac conductivity measurements. The temperature variation of the initial permeability of these samples was carried out from 30 °C to 200 °C. The dielectric constant, dielectric loss tangent and ac conductivity have been measured in the frequency range of 100 Hz to 1 MHz. Initial permeability and dielectric constant were found to increase and dielectric loss decreased with Cu substitution for Mg, up to x = 0.20. The ferrite powder prepared is suitable for the application in multilayer chip inductor due to its low-temperature sinterability, good magnetic properties and low loss at high frequency.     

Catalyst Design by NH4OH Treatment of USY Zeolite

Hierarchical zeolites are a class of superior catalysts which couples the intrinsic zeolitic properties to enhanced accessibility and intracrystalline mass transport to and from the active sites. The design of hierarchical USY (Ultra‐Stable Y) catalysts is achieved using a sustainable postsynthetic room temperature treatment with mildly alkaline NH₄OH (0.02 m ) solutions. Starting from a commercial dealuminated USY zeolite (Si/Al = 47), a hierarchical material is obtained by selective and tuneable creation of interconnected and accessible small mesopores (2–6 nm). In addition, the treatment immediately yields the NH₄⁺ form without the need for additional ion exchange. After NH₄OH modification, the crystal morphology is retained, whereas the microporosity and relative crystallinity are decreased. The gradual formation of dense amorphous phases throughout the crystal without significant framework atom leaching rationalizes the very high material yields (>90%). The superior catalytic performance of the developed hierarchical zeolites is demonstrated in the acid‐catalyzed isomerization of α‐pinene and the metal‐catalyzed conjugation of safflower oil. Significant improvements in activity and selectivity are attained, as well as a lowered susceptibility to deactivation. The catalytic performance is intimately related to the introduced mesopores, hence enhanced mass transport capacity, and the retained intrinsic zeolitic properties.     

Correction of post burns contracture of wrist with Ilizarov method

A case of severe post burns contracture of the wrist, of 43 years duration resulting in recurrent ulceration of the skin was successfully treated by gradual distraction using the Ilizarov method. This method is superior to plaster of Paris cast and is more versatile than other forms of external fixation.