油气集输系统新增产能建设拓扑优化方法研究

在油气集输新增产能建设中,为充分利用已建管网系统的处理能力,达到降低投资,提高经济效益的目的,进行了油气集输新增产能建设布局优化方法的研究。针对新建集输管网为树状结构的情况,建立了油气集输系统新增产能建设拓扑优化的数学模型,讨论了计算复杂性问题。根据模型的特点,将问题分解为拓扑级优化和几何级优化两个子问题,并通过它们之间的迭代进行求解。实例计算表明,所建立的数学模型正确,求解方法可行,能用于工程实际设计。     

定向爆破拆除框架式水塔

高 2 7m的水塔建于 193 4年 ,其顶部水罐由 12根钢筋混凝土柱支撑。在倒向侧 7根立柱上形成不同高度的爆破切口 ,背向侧倾倒中心线上的一根立柱上形成小爆破切口 ,其余 4根立柱底部打贯通孔 ,使水塔准确定向倾倒。文中讨论了立柱切口高度的计算 ,爆破参数的确定 ,并介绍了所采用的安全措施。     

Effect of Y2O3, CeO2 on Sintering Properties of Si3N4 Ceramics

The effect of rare earth oxides Y203 or Ce02 on sintering properties of Si3N4 ceramics was studied and the mechanism of assisting action during sintering was analyzed. The results in dicate that the best sintering properties appear in Si3N4 ceramics with 5% Y203 or 8% CeO2. Secondary crystallites are formed at grain boundaries after heat treatment,which decreases the amount of glass phase and contributes to the improvement of high-temperature mechanical properties of silicon nitride.     

Experience in testing the Motif interface

The testing and quality assurance of the Motif 1.0 graphical user-interface software are described. The testing goals, which fell into three general categories (code coverage, defect-density, and defect-arrival rate), and a deliverable formal test suite are examined. The three phases of the testing process-evaluation, test development, and regression testing-and the tools used in testing are discussed     

Novel Hyperbranched predominantly Alternating Copolymers Made From A Charge Transfer Complex monomer pair of p-(chloromethyl)styrene and Acrylonitrile via Controlled Living Radical Copolymerization

Summary Novel hyperbranched copolymers were successfully synthesized by the controlled charge transfer complex inimer and living radical copolymerization of p-(chloromethyl)styrene (PCMS) and acrylonitrile (AN). The resulting copolymers were characterized by SEC, NMR, FTIR, DSC and elemental analysis etc.. The influences of reaction conditions, such as the polymerization temperature, the catalyst (CuBr) concentration and the monomer ratio, on the resulting copolymers were investigated in detail. The monomer reactivity ratios were evaluated to be r_PCMS=0.937 and r_AN=0.088 respectively by the Fineman-Ross method. The higher are the polymerization temperature and the ratio of catalyst to monomer, the higher is the branching degree of the resulting copolymer. When the amount of monomer AN was used in excess than that of the monomer PCMS in the raw feed, the hyperbranched predominantly alternating copolymers HP[PCMS-co-AN] could be obtained. These hyperbranched copolymers were successfully used as functional macroinitiators to synthesize the star-shaped poly(PCMS-co-AN)/poly(MMA) block copolymers.     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

文件静态特性评估下的木马检测机制

本文提出了一种针对木马的静态信息进行分析的新的检测机制,建立了基于BP神经网络的数据处理模型。PE文件是Windows平台下的可执行文件,也是木马等后门程序的主要载体, 由于PE文件的结构复杂、灵活,而BP神经网络摸型的自身要求,导致数据的建摸过程遇到两个难点,本文首先引入了变化粒度的概念,解决了输入端非线性数据的问题。同时,也解决了将PE文件中大量的字符串归一化(0,1)区间)的问题,最终建立了一套较为理想的解决方案,取得了较为理想的测试数据。     

Crystal growth of selected II–VI semiconducting alloys by directional solidification: Part I Ground-based experiments

A series of Hg_0.84Zn_0.16 Te crystal ingots have been grown from pseudobinary melts by the Bridgmam–Stockbarger type directional solidification using a Marshall Space Flight Center/Space Science Laboratory heat-pipe furnace and the ground control experiment laboratory furnace of the crystal growth furnace which was flown on the first United States Microgravity Mission. A number of translation rates and a series of hot- and cold-zone temperatures were employed to assess the influence of growth parameters on the crystal properties for the purpose of optimizing the in-flight growth conditions. This revised version was published online in November 2006 with corrections to the Cover Date.     

连轧机用人字轮齿轴断裂失效分析

用宏观断口分析、化学检验、力学性能测定、低倍检查、金相组织及夹杂物评定鉴别、受力分析及强度寿命定量估算的方法，对人字轮被动齿轴端断裂失效原因进行分析，并提出改进措施。