Low-Temperature Materials and Thin Film Transistors for Flexible Electronics

This paper addresses the low-temperature deposition processes and electronic properties of silicon based thin film semiconductors and dielectrics to enable the fabrication of mechanically flexible electronic devices on plastic substrates. Device quality amorphous hydrogenated silicon (a-Si:H), nanocrystalline silicon (nc-Si), and amorphous silicon nitride (a-SiN/sub x/) films and thin film transistors (TFTs) were made using existing industrial plasma deposition equipment at the process temperatures as low as 75/spl deg/C and 120/spl deg/C. The a-Si:H TFTs fabricated at 120/spl deg/C demonstrate performance similar to their high-temperature counterparts, including the field effect mobility (/spl mu//sub FE/) of 0.8 cm/sup 2/V/sup -1/s/sup -1/, the threshold voltage (V/sub T/) of 4.5 V, and the subthreshold slope of 0.5 V/dec, and can be used in active matrix (AM) displays including organic light emitting diode (OLED) displays. The a-Si:H TFTs fabricated at 75/spl deg/C exhibit /spl mu//sub FE/ of 0.6 cm/sup 2/V/sup -1/s/sup -1/, and V/sub T/ of 4 V. It is shown that further improvement in TFT performance can be achieved by using n/sup +/ nc-Si contact layers and plasma treatments of the interface between the gate dielectric and the channel layer. The results demonstrate that with appropriate process optimization, the large area thin film Si technology suits well the fabrication of electronic devices on low-cost plastic substrates.     

Highly Efficient Orange and Green Solid‐State Light‐Emitting Electrochemical Cells Based on Cationic IrIII Complexes with Enhanced Steric Hindrance

Highly efficient orange and green emission from single‐layered solid‐state light‐emitting electrochemical cells based on cationic transition‐metal complexes [Ir(ppy)₂sb]PF₆ and [Ir(dFppy)₂sb]PF₆ (where ppy is 2‐phenylpyridine, dFppy is 2‐(2,4‐difluorophenyl)pyridine, and sb is 4,5‐diaza‐9,9′‐spirobifluorene) is reported. Photoluminescence measurements show highly retained quantum yields for [Ir(ppy)₂sb]PF₆ and [Ir(dFppy)₂ sb]PF₆ in neat films (compared with quantum yields of these complexes dispersed in m‐bis(N‐carbazolyl)benzene films). The spiroconfigured sb ligands effectively enhance the steric hindrance of the complexes and reduce the self‐quenching effect. The devices that use single‐layered neat films of [Ir(ppy)₂sb]PF₆ and [Ir(dFppy)₂sb]PF₆ achieve high peak external quantum efficiencies and power efficiencies of 7.1 % and 22.6 lm W^–1) at 2.5 V, and 7.1 % and 26.2 lm W^–1 at 2.8 V, respectively. These efficiencies are among the highest reported for solid‐state light‐emitting electrochemical cells, and indicate that cationic transition‐metal complexes containing ligands with good steric hindrance are excellent candidates for highly efficient solid‐state electrochemical cells.     

Waveband-switchable SOA ring laser constructed with a phase modulator loop mirror filter

An electrically tunable multiwavelength source has been developed using a birefringence-based optical comb filter in a semiconductor optical amplifier ring laser. The filter is constructed with an electrooptic phase modulator placed inside a fiber loop mirror. By controlling the birefringence of the modulator through the applied bias, the radio-frequency power, or the modulation frequency, we achieve a continuous shift of the spectral comb to access different interleaved wavebands. Electrical waveband switching has been successfully demonstrated for 21 wavelengths at 100-GHz grid spacing with an optical signal-to-noise ratio over 40 dB.     

Impact of nonlinear phase noise on direct-detection DQPSK WDM systems

The performance degradation of differential quadrature phase-shift keying (DQPSK) wavelength-division-multiplexed (WDM) systems due to self-phase modulation (SPM)- and cross-phase modulation (XPM)-induced nonlinear phase noise is evaluated in this letter. The XPM-induced nonlinear phase noise is approximated as Gaussian distribution and summed together with the SPM-induced nonlinear phase noise. We demonstrate that 10-Gb/s systems, whose walkoff length is larger than 40-Gb/s systems', are more sensitive to XPM-induced nonlinear phase noise than 40-Gb/s systems. Furthermore, DQPSK WDM systems show lower tolerance to both SPM- and XPM-induced nonlinear phase noise than differential phase-shift keying WDM systems.     

A 0.9 V 92 dB Double-Sampled Switched-RC Delta-Sigma Audio ADC

A 0.9 V third-order double-sampled delta-sigma audio ADC is presented. A new method using a combination of a switched-RC technique and a floating switched-capacitor double-sampling configuration enabled low-voltage operation without clock boosting or bootstrapping. A three-level quantizer with simple dynamic element matching was used to improve linearity. The prototype IC implemented in a 0.13 CMOS process achieves 92 dB DR, 91 dB SNR and 89 dB SNDR in a 24 kHz audio signal bandwidth, while consuming 1.5 mW from a 0.9 V supply. The prototype operates from 0.65 V to 1.5 V supply with minimal performance degradation.     

烯烃聚合单活性中心非茂催化剂的最新研究进展

综述了近几年来烯烃聚合用单活性中心非茂催化剂的研究进展。简要介绍了 2 3种由前、后过渡金属组成的配位化合物催化剂的结构与性能     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

Properties of nanoporous organosilicate hybrid thin films with a bimodal pore size distribution

Low dielectric poly[methylsilsesquioxane‐ran‐trifluoropropylsilsesquioxane‐ran‐(2,4,6,8‐tetramethyl‐2,4,6,8‐tetraethylenecyclotetrasiloxane)silsesquioxane]s {P[M‐ran‐TFP‐ran‐(TCS)]SSQs} having various compositions were synthesized using trifluoropropyl trimethoxysilane, methyl trimethoxysilane and 2,4,6,8‐tetramethyl‐2,4,6,8‐tetra(trimethoxysilylethyl)cyclotetrasiloxane. The chemical composition of the polymers and the content of SiOH end‐groups were controlled by adjusting the reaction conditions, and they were characterized by ¹H‐NMR. The thermally decomposable trifluoropropyl groups on the P[M‐ran‐TFP‐ran‐(TCS)]SSQ backbone and heptakis(2,3,6‐tri‐O‐methyl)‐β‐cyclodextrin (CD) were employed as pore generators. The dielectric constants of the porous CD/P[M‐ran‐TFP‐ran‐(TCS)]SSQ films were in the range 2.0–2.7 (at 100 kHz) depending on the concentration of the porogens, and showed no change over 4 days under aqueous conditions. The pore size of the films showed a bimodal distribution, with diameters of ca 0.5–1.0 nm for those originating from the trifluoropropyl groups and 1.7 nm from the CD. The elastic modulus and hardness of the 30 vol% CD‐blended film with a dielectric constant of 2.26 were 2.40 and 0.38 GPa, respectively, as determined by a nanoindenter. Copyright © 2005 Society of Chemical Industry     

Slow eroding biodegradable multiblock poloxamer copolymers

Biodegradable multiblock poloxamers (BMPs) with gel duration of 8 h to several weeks were prepared by varying their molecular weights from 4000 to 40 000 g mol^?1. The molecular weight of the BMP was controlled by changing the poloxamer to coupling agent ratio. Assuming a micelle packing model of the BMP gel, as in the case of a poloxamer gel, the micelle properties and critical gel concentration of BMPs were investigated on the basis of the scaling concept. The findings suggest that the control of molecular weight by hydrolyzable groups can be a facile approach to optimize the gel properties for biomedical applications. Copyright © 2005 Society of Chemical Industry     

Steric requirements for coal swelling by amine bases

A set of six coals ranging in rank from lignite to hvA bituminous was swollen with a series of alkyl-substituted pyridines and a smaller set of 4-alkylanilines. The size and branching of the alkyl groups was varied and the effect of this variation on the dissolution of the amines in the coal and the resulting coal swelling was measured volumetrically. In a few cases, substituents which hindered the amine nitrogen were studied. The lignite and subbituminous coal have a much higher tolerance to branched, bulky groups than do the bituminous coals. The presence of tertiary groups in a solute strongly inhibits their dissolution in bituminous coals. Bituminous coals behave as if extensive parallel packing of structures occurs. Often, they can accept very large planar groups but have a low capacity for branched groups.